* [PATCH 1/2] ARM: at91/dt: at91sam9260: Remove leading zeros in OHCI node.
@ 2016-05-25 8:15 Raashid Muhammed
2016-05-25 8:15 ` [PATCH 2/2] ARM: at91: Add DT support for Olimex SAM9-L9260 board Raashid Muhammed
0 siblings, 1 reply; 3+ messages in thread
From: Raashid Muhammed @ 2016-05-25 8:15 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, linux,
nicolas.ferre, alexandre.belloni, plagnioj, vijaykumar,
devicetree, linux-kernel, linux-arm-kernel
Cc: Raashid Muhammed
From: Raashid Muhammed <raashidmuhammed@zilogic.com>
Remove leading zeros in OHCI node for at91sam9260 based boards.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
---
arch/arm/boot/dts/aks-cdu.dts | 2 +-
arch/arm/boot/dts/animeo_ip.dts | 2 +-
arch/arm/boot/dts/at91-foxg20.dts | 2 +-
arch/arm/boot/dts/at91-kizbox.dts | 2 +-
arch/arm/boot/dts/at91-qil_a9260.dts | 2 +-
arch/arm/boot/dts/at91sam9260.dtsi | 2 +-
arch/arm/boot/dts/at91sam9g20ek_common.dtsi | 2 +-
arch/arm/boot/dts/ethernut5.dts | 2 +-
arch/arm/boot/dts/evk-pro3.dts | 2 +-
arch/arm/boot/dts/usb_a9260_common.dtsi | 2 +-
10 files changed, 10 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/aks-cdu.dts b/arch/arm/boot/dts/aks-cdu.dts
index d9c50fb..5b1bf92 100644
--- a/arch/arm/boot/dts/aks-cdu.dts
+++ b/arch/arm/boot/dts/aks-cdu.dts
@@ -57,7 +57,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts
index 0962f2f..8bcbad3 100644
--- a/arch/arm/boot/dts/animeo_ip.dts
+++ b/arch/arm/boot/dts/animeo_ip.dts
@@ -114,7 +114,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
atmel,vbus-gpio = <&pioB 15 GPIO_ACTIVE_LOW>;
status = "okay";
diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/at91-foxg20.dts
index 6bf873e..42a535d 100644
--- a/arch/arm/boot/dts/at91-foxg20.dts
+++ b/arch/arm/boot/dts/at91-foxg20.dts
@@ -128,7 +128,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 229e989..0e3f34e 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -54,7 +54,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <1>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/at91-qil_a9260.dts
index 4f2eebf..5309e19 100644
--- a/arch/arm/boot/dts/at91-qil_a9260.dts
+++ b/arch/arm/boot/dts/at91-qil_a9260.dts
@@ -111,7 +111,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index d4884dd..af5ba31 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -1007,7 +1007,7 @@
status = "disabled";
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
compatible = "atmel,at91rm9200-ohci", "usb-ohci";
reg = <0x00500000 0x100000>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 2>;
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index e9cc99b..1395b30 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -170,7 +170,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/ethernut5.dts b/arch/arm/boot/dts/ethernut5.dts
index 2430443..298ee2f 100644
--- a/arch/arm/boot/dts/ethernut5.dts
+++ b/arch/arm/boot/dts/ethernut5.dts
@@ -77,7 +77,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/evk-pro3.dts b/arch/arm/boot/dts/evk-pro3.dts
index f72969e..312d3e8 100644
--- a/arch/arm/boot/dts/evk-pro3.dts
+++ b/arch/arm/boot/dts/evk-pro3.dts
@@ -46,7 +46,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
diff --git a/arch/arm/boot/dts/usb_a9260_common.dtsi b/arch/arm/boot/dts/usb_a9260_common.dtsi
index 9beea89..12119b5 100644
--- a/arch/arm/boot/dts/usb_a9260_common.dtsi
+++ b/arch/arm/boot/dts/usb_a9260_common.dtsi
@@ -90,7 +90,7 @@
};
};
- usb0: ohci@00500000 {
+ usb0: ohci@500000 {
num-ports = <2>;
status = "okay";
};
--
2.1.4
^ permalink raw reply related [flat|nested] 3+ messages in thread* [PATCH 2/2] ARM: at91: Add DT support for Olimex SAM9-L9260 board.
2016-05-25 8:15 [PATCH 1/2] ARM: at91/dt: at91sam9260: Remove leading zeros in OHCI node Raashid Muhammed
@ 2016-05-25 8:15 ` Raashid Muhammed
2016-05-25 19:08 ` Rob Herring
0 siblings, 1 reply; 3+ messages in thread
From: Raashid Muhammed @ 2016-05-25 8:15 UTC (permalink / raw)
To: robh+dt, pawel.moll, mark.rutland, ijc+devicetree, galak, linux,
nicolas.ferre, alexandre.belloni, plagnioj, vijaykumar,
devicetree, linux-kernel, linux-arm-kernel
Cc: Raashid Muhammed
From: Raashid Muhammed <raashidmuhammed@zilogic.com>
sam9-l9260 is a low cost board designed by Olimex.
More information is available at:
https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
---
Documentation/devicetree/bindings/arm/olimex.txt | 8 +-
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sam9_l9260.dts | 115 +++++++++++++++++++++++
3 files changed, 122 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/boot/dts/at91-sam9_l9260.dts
diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt
index 007fb5c..d726aec 100644
--- a/Documentation/devicetree/bindings/arm/olimex.txt
+++ b/Documentation/devicetree/bindings/arm/olimex.txt
@@ -1,5 +1,9 @@
-Olimex i.MX Platforms Device Tree Bindings
-------------------------------------------
+Olimex Device Tree Bindings
+---------------------------
+
+SAM9-L9260 Board
+Required root node properties:
+ - compatible = "olimex,sam9-l9260", "atmel,at91sam9260";
i.MX23 Olinuxino Low Cost Board
Required root node properties:
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0f89d87..d27f09d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -19,6 +19,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
usb_a9260.dtb \
at91sam9261ek.dtb \
at91sam9263ek.dtb \
+ at91-sam9_l9260.dtb \
tny_a9263.dtb \
usb_a9263.dtb \
at91-foxg20.dtb \
diff --git a/arch/arm/boot/dts/at91-sam9_l9260.dts b/arch/arm/boot/dts/at91-sam9_l9260.dts
new file mode 100644
index 0000000..e2da9b906
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sam9_l9260.dts
@@ -0,0 +1,115 @@
+/*
+ * at91-sam9_l9260.dts - Device Tree file for Olimex SAM9-L9260 board
+ *
+ * Copyright (C) 2016 Raashid Muhammed <raashidmuhammed@zilogic.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "at91sam9260.dtsi"
+
+/ {
+ model = "Olimex sam9-l9260";
+ compatible = "olimex,sam9-l9260", "atmel,at91sam9260", "atmel,at91sam9";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <18432000>;
+ };
+ };
+
+ ahb {
+ apb {
+ mmc0: mmc@fffa8000 {
+ pinctrl-0 = <
+ &pinctrl_board_mmc0
+ &pinctrl_mmc0_clk
+ &pinctrl_mmc0_slot1_cmd_dat0
+ &pinctrl_mmc0_slot1_dat1_3>;
+ status = "okay";
+
+ slot@1 {
+ reg = <1>;
+ bus-width = <4>;
+ cd-gpios = <&pioC 8 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&pioC 4 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ macb0: ethernet@fffc4000 {
+ phy-mode = "mii";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ ethernet-phy@1 {
+ reg = <0x1>;
+ };
+ };
+
+ spi0: spi@fffc8000 {
+ cs-gpios = <&pioC 11 0>, <0>, <0>, <0>;
+ status = "okay";
+
+ mtd_dataflash@0 {
+ compatible = "atmel,at45", "atmel,dataflash";
+ spi-max-frequency = <15000000>;
+ reg = <0>;
+ };
+ };
+
+ dbgu: serial@fffff200 {
+ status = "okay";
+ };
+
+ pinctrl@fffff400 {
+ mmc0 {
+ pinctrl_board_mmc0: mmc0-board {
+ atmel,pins =
+ <AT91_PIOC 8 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH /* CD pin */
+ AT91_PIOC 4 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>; /* WP pin */
+ };
+ };
+ };
+ };
+
+ nand0: nand@40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt = <1>;
+ status = "okay";
+ };
+
+ usb0: ohci@500000 {
+ status = "okay";
+ };
+
+ };
+
+ i2c@0 {
+ status = "okay";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ b0 {
+ label = "b0";
+ gpios = <&pioA 6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ };
+};
--
2.1.4
^ permalink raw reply related [flat|nested] 3+ messages in thread* Re: [PATCH 2/2] ARM: at91: Add DT support for Olimex SAM9-L9260 board.
2016-05-25 8:15 ` [PATCH 2/2] ARM: at91: Add DT support for Olimex SAM9-L9260 board Raashid Muhammed
@ 2016-05-25 19:08 ` Rob Herring
0 siblings, 0 replies; 3+ messages in thread
From: Rob Herring @ 2016-05-25 19:08 UTC (permalink / raw)
To: Raashid Muhammed
Cc: pawel.moll, mark.rutland, ijc+devicetree, galak, linux,
nicolas.ferre, alexandre.belloni, plagnioj, vijaykumar,
devicetree, linux-kernel, linux-arm-kernel
On Wed, May 25, 2016 at 01:45:06PM +0530, Raashid Muhammed wrote:
> From: Raashid Muhammed <raashidmuhammed@zilogic.com>
>
> sam9-l9260 is a low cost board designed by Olimex.
>
> More information is available at:
> https://www.olimex.com/Products/ARM/Atmel/SAM9-L9260/
>
> Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
> Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
> ---
> Documentation/devicetree/bindings/arm/olimex.txt | 8 +-
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-sam9_l9260.dts | 115 +++++++++++++++++++++++
> 3 files changed, 122 insertions(+), 2 deletions(-)
> create mode 100644 arch/arm/boot/dts/at91-sam9_l9260.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/olimex.txt b/Documentation/devicetree/bindings/arm/olimex.txt
> index 007fb5c..d726aec 100644
> --- a/Documentation/devicetree/bindings/arm/olimex.txt
> +++ b/Documentation/devicetree/bindings/arm/olimex.txt
> @@ -1,5 +1,9 @@
> -Olimex i.MX Platforms Device Tree Bindings
> -------------------------------------------
> +Olimex Device Tree Bindings
> +---------------------------
> +
> +SAM9-L9260 Board
> +Required root node properties:
> + - compatible = "olimex,sam9-l9260", "atmel,at91sam9260";
>
> i.MX23 Olinuxino Low Cost Board
> Required root node properties:
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 0f89d87..d27f09d 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -19,6 +19,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
> usb_a9260.dtb \
> at91sam9261ek.dtb \
> at91sam9263ek.dtb \
> + at91-sam9_l9260.dtb \
> tny_a9263.dtb \
> usb_a9263.dtb \
> at91-foxg20.dtb \
> diff --git a/arch/arm/boot/dts/at91-sam9_l9260.dts b/arch/arm/boot/dts/at91-sam9_l9260.dts
> new file mode 100644
> index 0000000..e2da9b906
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-sam9_l9260.dts
> @@ -0,0 +1,115 @@
> +/*
> + * at91-sam9_l9260.dts - Device Tree file for Olimex SAM9-L9260 board
> + *
> + * Copyright (C) 2016 Raashid Muhammed <raashidmuhammed@zilogic.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +/dts-v1/;
> +#include "at91sam9260.dtsi"
> +
> +/ {
> + model = "Olimex sam9-l9260";
> + compatible = "olimex,sam9-l9260", "atmel,at91sam9260", "atmel,at91sam9";
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory {
> + reg = <0x20000000 0x4000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <18432000>;
> + };
> + };
> +
> + ahb {
The whitespace is off here and throughout. You've got a <tab><space>...
Otherwise,
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2016-05-25 19:08 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-05-25 8:15 [PATCH 1/2] ARM: at91/dt: at91sam9260: Remove leading zeros in OHCI node Raashid Muhammed
2016-05-25 8:15 ` [PATCH 2/2] ARM: at91: Add DT support for Olimex SAM9-L9260 board Raashid Muhammed
2016-05-25 19:08 ` Rob Herring
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).