* [PATCH v2] ARM: dts: imx: add Gateworks Ventana GW553x support
@ 2016-06-29 13:32 Tim Harvey
[not found] ` <1467207146-4842-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
0 siblings, 1 reply; 4+ messages in thread
From: Tim Harvey @ 2016-06-29 13:32 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
- micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
---
v2:
- add dual license to *.dts files
- add prop for external watchdog reset
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw553x.dts | 55 +++++
arch/arm/boot/dts/imx6q-gw553x.dts | 55 +++++
arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 1 -
arch/arm/boot/dts/imx6qdl-gw553x.dtsi | 444 ++++++++++++++++++++++++++++++++++
5 files changed, 556 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/imx6dl-gw553x.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw553x.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw553x.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 1e13fcc..3a305ca 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -318,6 +318,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw54xx.dtb \
imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
+ imx6dl-gw553x.dtb \
imx6dl-hummingboard.dtb \
imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
@@ -356,6 +357,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw54xx.dtb \
imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
+ imx6q-gw553x.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-icore-rqs.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw553x.dts b/arch/arm/boot/dts/imx6dl-gw553x.dts
new file mode 100644
index 0000000..59b8afc3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw553x.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW553X";
+ compatible = "gw,imx6dl-gw553x", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw553x.dts b/arch/arm/boot/dts/imx6q-gw553x.dts
new file mode 100644
index 0000000..e9c224c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw553x.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW553X";
+ compatible = "gw,imx6q-gw553x", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index a3dd0c4..e5f4b6c 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -86,7 +86,6 @@
regulator-always-on;
};
- /* remove when pmic 1p8 regulator available */
reg_1p8v: regulator@1 {
compatible = "regulator-fixed";
reg = <1>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
new file mode 100644
index 0000000..d683e08
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
@@ -0,0 +1,444 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ nand = &gpmi;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ bootargs = "console=ttymxc1,115200";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+ };
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_3p3v: regulator@0 {
+ compatible = "regulator-fixed";
+ reg = <0>;
+ regulator-name = "3P0V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0v: regulator@1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator@2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ eeprom1: eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom2: eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom3: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom4: eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ gpio: pca9555@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ rtc: ds1672@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ imx6qdl-gw553x {
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b0 /* PCIESKT_WDIS# */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
+ >;
+ };
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v2] ARM: dts: imx: add Gateworks Ventana GW553x support
[not found] ` <1467207146-4842-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
@ 2016-08-08 8:30 ` Shawn Guo
2016-08-09 18:49 ` [PATCH v3] " Tim Harvey
1 sibling, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2016-08-08 8:30 UTC (permalink / raw)
To: Tim Harvey
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Wed, Jun 29, 2016 at 06:32:26AM -0700, Tim Harvey wrote:
> diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> index a3dd0c4..e5f4b6c 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> @@ -86,7 +86,6 @@
> regulator-always-on;
> };
>
> - /* remove when pmic 1p8 regulator available */
Is this change related?
> reg_1p8v: regulator@1 {
> compatible = "regulator-fixed";
> reg = <1>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
> new file mode 100644
> index 0000000..d683e08
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
<snip>
> + chosen {
> + bootargs = "console=ttymxc1,115200";
A 'stdout-path' should make more sense here.
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpio_leds>;
> +
> + led0: user1 {
> + label = "user1";
> + gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
> + default-state = "on";
> + linux,default-trigger = "heartbeat";
> + };
> +
> + led1: user2 {
> + label = "user2";
> + gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
> + default-state = "off";
> + };
> + };
> +
> + memory {
> + reg = <0x10000000 0x20000000>;
> + };
> +
> + pps {
> + compatible = "pps-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pps>;
> + gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <0>;
We had stopped doing this for a while, because DT maintainers do not
like this fake simple-bus container. Please put the fixed regulator
nodes directly under root with following naming schema.
reg_xxx: regulator-xxx {
...
};
> +
> + reg_3p3v: regulator@0 {
> + compatible = "regulator-fixed";
> + reg = <0>;
> + regulator-name = "3P0V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_5p0v: regulator@1 {
> + compatible = "regulator-fixed";
> + reg = <1>;
> + regulator-name = "5P0V";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: regulator@2 {
> + compatible = "regulator-fixed";
> + reg = <2>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> + };
> +};
> +
> +&gpmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_gpmi_nand>;
> + status = "okay";
> +};
> +
> +&hdmi {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hdmi>;
> + ddc-i2c-bus = <&i2c3>;
> + status = "okay";
> +};
> +
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "okay";
> +
> + eeprom1: eeprom@50 {
> + compatible = "atmel,24c02";
> + reg = <0x50>;
> + pagesize = <16>;
> + };
> +
> + eeprom2: eeprom@51 {
> + compatible = "atmel,24c02";
> + reg = <0x51>;
> + pagesize = <16>;
> + };
> +
> + eeprom3: eeprom@52 {
> + compatible = "atmel,24c02";
> + reg = <0x52>;
> + pagesize = <16>;
> + };
> +
> + eeprom4: eeprom@53 {
> + compatible = "atmel,24c02";
> + reg = <0x53>;
> + pagesize = <16>;
> + };
> +
> + gpio: pca9555@23 {
> + compatible = "nxp,pca9555";
> + reg = <0x23>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + };
We generally sort the device nodes under I2C bus in order of slave
address. That said, this pca9555@23 node should go before eeprom@50.
> +
> + rtc: ds1672@68 {
> + compatible = "dallas,ds1672";
> + reg = <0x68>;
> + };
> +};
<snip>
> +&iomuxc {
> + imx6qdl-gw553x {
Since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT without
function nodes), this function container node is no longer needed.
Shawn
> + pinctrl_gpmi_nand: gpminandgrp {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
> + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
> + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
> + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
> + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
> + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
> + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
> + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
> + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
> + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
> + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
> + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
> + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
> + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
> + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
> + >;
> + };
> +
> + pinctrl_hdmi: hdmigrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
> + >;
> + };
> +
> + pinctrl_gpio_leds: gpioledsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> + MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
> + >;
> + };
> +
> + pinctrl_pcie: pciegrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
> + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b0 /* PCIESKT_WDIS# */
> + >;
> + };
> +
> + pinctrl_pps: ppsgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
> + >;
> + };
> +
> + pinctrl_pwm2: pwm2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart3: uart3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart4: uart4grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_uart5: uart5grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */
> + MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */
> + MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
> + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */
> + MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
> + >;
> + };
> + };
> +};
> --
> 1.9.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH v3] ARM: dts: imx: add Gateworks Ventana GW553x support
[not found] ` <1467207146-4842-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
2016-08-08 8:30 ` Shawn Guo
@ 2016-08-09 18:49 ` Tim Harvey
[not found] ` <1470768547-869-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
1 sibling, 1 reply; 4+ messages in thread
From: Tim Harvey @ 2016-08-09 18:49 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA
The Gateworks Ventana GW553x is a single-board computer based on the NXP
IMX6 SoC with the following features:
* IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
* small form factor (35x70mm)
* 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
* 256MB NAND flash (4GB option)
* Gateworks System Controller:
- hardware watchdog
- hardware monitor
- pushbutton controller
- EEPROM storage
- power control
* JTAG programmable
* 1x miniPCI socket (with PCIe, USB, SIM)
* 1x microSD socket
* 1x SIM socket
* Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
* analog CVBS video in
* GPS (optional uBlox EVA-M8M)
* Application headers:
- 2x TTL UART (TX/RX)
- 4x TTL GPIO (3x configurable as PWM)
- 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
* Front panel connectors:
- micro-HDMI audio/video out
- 1x user programmable LED
- 1x configurable user pushbutton
- 1x USB OTG
See http://www.gateworks.com for more info
Signed-off-by: Tim Harvey <tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
---
v3:
- removed unintentional change to imx6qdl-gw53xx.dtsi
- replaced bootargs with stdout-path in chosen node
- move fixed regulators directly under root node
- sort i2c child nodes by slave address
- removed function container node from iomux node that is no longer needed
v2:
- add dual license to *.dts files
- add prop for external watchdog reset
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-gw553x.dts | 55 +++++
arch/arm/boot/dts/imx6q-gw553x.dts | 55 +++++
arch/arm/boot/dts/imx6qdl-gw553x.dtsi | 433 ++++++++++++++++++++++++++++++++++
4 files changed, 545 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-gw553x.dts
create mode 100644 arch/arm/boot/dts/imx6q-gw553x.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-gw553x.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 98c4b9d..dbd6a35 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -330,6 +330,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-gw54xx.dtb \
imx6dl-gw551x.dtb \
imx6dl-gw552x.dtb \
+ imx6dl-gw553x.dtb \
imx6dl-hummingboard.dtb \
imx6dl-nit6xlite.dtb \
imx6dl-nitrogen6x.dtb \
@@ -368,6 +369,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-gw54xx.dtb \
imx6q-gw551x.dtb \
imx6q-gw552x.dtb \
+ imx6q-gw553x.dtb \
imx6q-h100.dtb \
imx6q-hummingboard.dtb \
imx6q-icore-rqs.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-gw553x.dts b/arch/arm/boot/dts/imx6dl-gw553x.dts
new file mode 100644
index 0000000..59b8afc3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-gw553x.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 DualLite/Solo GW553X";
+ compatible = "gw,imx6dl-gw553x", "gw,ventana", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6q-gw553x.dts b/arch/arm/boot/dts/imx6q-gw553x.dts
new file mode 100644
index 0000000..e9c224c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-gw553x.dts
@@ -0,0 +1,55 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-gw553x.dtsi"
+
+/ {
+ model = "Gateworks Ventana i.MX6 Dual/Quad GW553X";
+ compatible = "gw,imx6q-gw553x", "gw,ventana", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
new file mode 100644
index 0000000..86cec05
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
@@ -0,0 +1,433 @@
+/*
+ * Copyright 2016 Gateworks Corporation
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public
+ * License along with this file; if not, write to the Free
+ * Software Foundation, Inc., 51 Franklin St, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ /* these are used by bootloader for disabling nodes */
+ aliases {
+ led0 = &led0;
+ led1 = &led1;
+ nand = &gpmi;
+ usb0 = &usbh1;
+ usb1 = &usbotg;
+ };
+
+ chosen {
+ stdout-path = &uart2;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led0: user1 {
+ label = "user1";
+ gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDG */
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led1: user2 {
+ label = "user2";
+ gpios = <&gpio4 11 GPIO_ACTIVE_HIGH>; /* MX6_PANLEDR */
+ default-state = "off";
+ };
+ };
+
+ memory {
+ reg = <0x10000000 0x20000000>;
+ };
+
+ pps {
+ compatible = "pps-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pps>;
+ gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P0V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_5p0v: regulator-5p0v {
+ compatible = "regulator-fixed";
+ regulator-name = "5P0V";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb_otg_vbus: regulator-usb-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c3>;
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ gpio: pca9555@23 {
+ compatible = "nxp,pca9555";
+ reg = <0x23>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ eeprom1: eeprom@50 {
+ compatible = "atmel,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+
+ eeprom2: eeprom@51 {
+ compatible = "atmel,24c02";
+ reg = <0x51>;
+ pagesize = <16>;
+ };
+
+ eeprom3: eeprom@52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <16>;
+ };
+
+ eeprom4: eeprom@53 {
+ compatible = "atmel,24c02";
+ reg = <0x53>;
+ pagesize = <16>;
+ };
+
+ rtc: ds1672@68 {
+ compatible = "dallas,ds1672";
+ reg = <0x68>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+};
+
+&pcie {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pcie>;
+ reset-gpio = <&gpio1 0 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm2>; /* MX6_DIO1 */
+ status = "disabled";
+};
+
+&pwm3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm3>; /* MX6_DIO2 */
+ status = "disabled";
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm4>; /* MX6_DIO3 */
+ status = "disabled";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbh1 {
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <®_3p3v>;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl_gpmi_nand: gpminandgrp {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1
+ MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x1b0b0
+ >;
+ };
+
+ pinctrl_pcie: pciegrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0
+ MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x4001b0b0 /* PCIESKT_WDIS# */
+ >;
+ };
+
+ pinctrl_pps: ppsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm2: pwm2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm3: pwm3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_pwm4: pwm4grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0 /* OTG_PWR_EN */
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x17059 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x17059
+ >;
+ };
+
+ pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170b9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x170f9 /* CD */
+ MX6QDL_PAD_NANDF_CS1__SD3_VSELECT 0x170f9
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__WDOG1_B 0x1b0b0
+ >;
+ };
+};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 4+ messages in thread
* Re: [PATCH v3] ARM: dts: imx: add Gateworks Ventana GW553x support
[not found] ` <1470768547-869-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
@ 2016-08-15 12:15 ` Shawn Guo
0 siblings, 0 replies; 4+ messages in thread
From: Shawn Guo @ 2016-08-15 12:15 UTC (permalink / raw)
To: Tim Harvey
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r
On Tue, Aug 09, 2016 at 11:49:07AM -0700, Tim Harvey wrote:
> The Gateworks Ventana GW553x is a single-board computer based on the NXP
> IMX6 SoC with the following features:
> * IMX6 DualLite Soc (supports IMX6S,IMX6DL,IMX6Q)
> * small form factor (35x70mm)
> * 512MB DDR3 DRAM (2x32bit) (options up to 2GB)
> * 256MB NAND flash (4GB option)
> * Gateworks System Controller:
> - hardware watchdog
> - hardware monitor
> - pushbutton controller
> - EEPROM storage
> - power control
> * JTAG programmable
> * 1x miniPCI socket (with PCIe, USB, SIM)
> * 1x microSD socket
> * 1x SIM socket
> * Inertial Module (LSM9DS1 9DOF: 3x acc, 3x rate, 3x mag)
> * analog CVBS video in
> * GPS (optional uBlox EVA-M8M)
> * Application headers:
> - 2x TTL UART (TX/RX)
> - 4x TTL GPIO (3x configurable as PWM)
> - 3x CVBS Analog video input (1x decoder with 3x selectable inputs)
> * Front panel connectors:
> - micro-HDMI audio/video out
> - 1x user programmable LED
> - 1x configurable user pushbutton
> - 1x USB OTG
>
> See http://www.gateworks.com for more info
>
> Signed-off-by: Tim Harvey <tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
Applied, thanks.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2016-08-15 12:15 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-06-29 13:32 [PATCH v2] ARM: dts: imx: add Gateworks Ventana GW553x support Tim Harvey
[not found] ` <1467207146-4842-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
2016-08-08 8:30 ` Shawn Guo
2016-08-09 18:49 ` [PATCH v3] " Tim Harvey
[not found] ` <1470768547-869-1-git-send-email-tharvey-UMMOYl/HMS+akBO8gow8eQ@public.gmane.org>
2016-08-15 12:15 ` Shawn Guo
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).