[PATCH v2 1/4] dt-binding: remoteproc: Introduce ADSP loader binding

[Bjorn Andersson <bjorn.andersson@linaro.org>]

This document defines the binding for a component that loads firmware
and control the life cycle of the Qualcomm ADSP core.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---

Changes since v1:
- Added platform names to compatibility

 .../devicetree/bindings/remoteproc/qcom,adsp.txt   | 70 ++++++++++++++++++++++
 1 file changed, 70 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt

diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt
new file mode 100644
index 000000000000..3820151ce3e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,adsp.txt
@@ -0,0 +1,70 @@
+Qualcomm ADSP Peripheral Image Loader
+
+This document defines the binding for a component that loads and boots firmware
+on the Qualcomm ADSP core.
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be one of:
+		    "qcom,msm8974-adsp-pil"
+		    "qcom,msm8996-adsp-pil"
+
+- interrupts-extended:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: must list the watchdog, fatal IRQs ready, handover and
+		    stop-ack IRQs
+
+- interrupt-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "wdog", "fatal", "ready", "handover", "stop-ack"
+
+- cx-supply:
+	Usage: required
+	Value type: <phandle>
+	Definition: reference to the regulator to be held on behalf of the
+		    booting of the Hexagon core
+
+- memory-region:
+	Usage: required
+	Value type: <phandle>
+	Definition: reference to the reserved-memory for the ADSP
+
+- qcom,smem-states:
+	Usage: required
+	Value type: <phandle>
+	Definition: reference to the smem state for requesting the ADSP to
+		    shut down
+
+- qcom,smem-state-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: must be "stop"
+
+= EXAMPLE
+The following example describes the resources needed to boot control the
+ADSP, as it is found on MSM8974 boards.
+
+	adsp {
+		compatible = "qcom,adsp-pil";
+
+		interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>,
+				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+		interrupt-names = "wdog",
+				  "fatal",
+				  "ready",
+				  "handover",
+				  "stop-ack";
+
+		cx-supply = <&pm8841_s2>;
+
+		memory-region = <&adsp_region>;
+
+		qcom,smem-states = <&modem_smp2p_out 0>;
+		qcom,smem-state-names = "stop";
+	};
-- 
2.5.0