From: Neil Armstrong <narmstrong@baylibre.com>
To: khilman@baylibre.com, carlo@caione.org,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-amlogic@lists.infradead.org, linux-kernel@vger.kernel.org
Cc: Neil Armstrong <narmstrong@baylibre.com>
Subject: [RFC PATCH 1/3] ARM64: dts: amlogic: Add Meson GX Family common dtsi
Date: Mon, 29 Aug 2016 09:56:09 +0200 [thread overview]
Message-ID: <1472457371-1305-2-git-send-email-narmstrong@baylibre.com> (raw)
In-Reply-To: <1472457371-1305-1-git-send-email-narmstrong@baylibre.com>
Introduce a common DTSI for Amlogic Meson GX Family including the
GXBB SoC and the GLX SoCs (S905X and S905D).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
---
arch/arm64/boot/dts/amlogic/meson-gx-common.dtsi | 181 +++++++++++++++++++++++
1 file changed, 181 insertions(+)
create mode 100644 arch/arm64/boot/dts/amlogic/meson-gx-common.dtsi
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-common.dtsi
new file mode 100644
index 0000000..fb393e9
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-common.dtsi
@@ -0,0 +1,181 @@
+/*
+ * Copyright (c) 2016 BayLibre, SAS.
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ *
+ * Copyright (c) 2016 Endless Computers, Inc.
+ * Author: Carlo Caione <carlo@endlessm.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <0x2>;
+ #size-cells = <0x0>;
+
+ cpu0: cpu@0 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ };
+
+ cpu1: cpu@1 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ };
+
+ cpu2: cpu@2 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x2>;
+ enable-method = "psci";
+ };
+
+ cpu3: cpu@3 {
+ device_type = "cpu";
+ compatible = "arm,cortex-a53", "arm,armv8";
+ reg = <0x0 0x3>;
+ enable-method = "psci";
+ };
+ };
+
+ arm-pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
+ };
+
+ xtal: xtal-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "xtal";
+ #clock-cells = <0>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ cbus: cbus@c1100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc1100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
+
+ uart_A: serial@84c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x084c0 0x0 0x14>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ gic: interrupt-controller@c4301000 {
+ compatible = "arm,gic-400";
+ reg = <0x0 0xc4301000 0 0x1000>,
+ <0x0 0xc4302000 0 0x2000>,
+ <0x0 0xc4304000 0 0x2000>,
+ <0x0 0xc4306000 0 0x2000>;
+ interrupt-controller;
+ interrupts = <GIC_PPI 9
+ (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ };
+
+ aobus: aobus@c8100000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xc8100000 0x0 0x100000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
+
+ uart_AO: serial@4c0 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x004c0 0x0 0x14>;
+ interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+ };
+
+ apb: apb@d0000000 {
+ compatible = "simple-bus";
+ reg = <0x0 0xd0000000 0x0 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
+ };
+ };
+};
--
1.9.1
next prev parent reply other threads:[~2016-08-29 7:56 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-29 7:56 [RFC PATCH 0/3] ARm64: amlogic: Introduce common GX family dtsi Neil Armstrong
2016-08-29 7:56 ` Neil Armstrong [this message]
2016-08-29 7:56 ` [RFC PATCH 2/3] ARM64: dts: amlogic: Switch Meson GXL dtsi to use common GX dtsi Neil Armstrong
[not found] ` <1472457371-1305-1-git-send-email-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
2016-08-29 7:56 ` [RFC PATCH 3/3] ARM64: dts: amlogic: Switch Meson GXBB " Neil Armstrong
2016-08-29 8:01 ` [RFC PATCH 0/3] ARm64: amlogic: Introduce common GX family dtsi Carlo Caione
[not found] ` <CAOQ7t2YGbASh7v25wgDspKNWgFOcRsikJs_WZptn+LkVXmaHig-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-08-29 18:38 ` Andreas Färber
2016-08-29 19:50 ` Carlo Caione
2016-08-29 20:15 ` Andreas Färber
[not found] ` <ca513cb4-34d4-72f9-9e32-7908329243a6-l3A5Bk7waGM@public.gmane.org>
2016-08-30 8:33 ` Neil Armstrong
2016-08-31 19:32 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1472457371-1305-2-git-send-email-narmstrong@baylibre.com \
--to=narmstrong@baylibre.com \
--cc=carlo@caione.org \
--cc=devicetree@vger.kernel.org \
--cc=khilman@baylibre.com \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).