From: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
To: khilman-rdvid1DuHRBWk0Htik3J/w@public.gmane.org,
carlo-KA+7E9HrN00dnm+yROfE0A@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Subject: [RFC PATCH 3/3] ARM64: dts: amlogic: Switch Meson GXBB dtsi to use common GX dtsi
Date: Mon, 29 Aug 2016 09:56:11 +0200 [thread overview]
Message-ID: <1472457371-1305-4-git-send-email-narmstrong@baylibre.com> (raw)
In-Reply-To: <1472457371-1305-1-git-send-email-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
The Amlogic Meson GXBB should use the common GX dtsi as base.
Signed-off-by: Neil Armstrong <narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
---
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi | 320 +++++++++-------------------
1 file changed, 99 insertions(+), 221 deletions(-)
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
index 2ea7bbd..e1e22fd 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi
@@ -40,9 +40,7 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "meson-gx-common.dtsi"
#include <dt-bindings/gpio/meson-gxbb-gpio.h>
#include <dt-bindings/reset/amlogic,meson-gxbb-reset.h>
#include <dt-bindings/clock/gxbb-clkc.h>
@@ -51,185 +49,8 @@
/ {
compatible = "amlogic,meson-gxbb";
- interrupt-parent = <&gic>;
- #address-cells = <2>;
- #size-cells = <2>;
-
- cpus {
- #address-cells = <0x2>;
- #size-cells = <0x0>;
-
- cpu0: cpu@0 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x0>;
- enable-method = "psci";
- };
-
- cpu1: cpu@1 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x1>;
- enable-method = "psci";
- };
-
- cpu2: cpu@2 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x2>;
- enable-method = "psci";
- };
-
- cpu3: cpu@3 {
- device_type = "cpu";
- compatible = "arm,cortex-a53", "arm,armv8";
- reg = <0x0 0x3>;
- enable-method = "psci";
- };
- };
-
- arm-pmu {
- compatible = "arm,cortex-a53-pmu";
- interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
- };
-
- psci {
- compatible = "arm,psci-0.2";
- method = "smc";
- };
-
- timer {
- compatible = "arm,armv8-timer";
- interrupts = <GIC_PPI 13
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 14
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 11
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>,
- <GIC_PPI 10
- (GIC_CPU_MASK_RAW(0xff) | IRQ_TYPE_EDGE_RISING)>;
- };
-
- xtal: xtal-clk {
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "xtal";
- #clock-cells = <0>;
- };
soc {
- compatible = "simple-bus";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- cbus: cbus@c1100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc1100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc1100000 0x0 0x100000>;
-
- reset: reset-controller@4404 {
- compatible = "amlogic,meson-gxbb-reset";
- reg = <0x0 0x04404 0x0 0x20>;
- #reset-cells = <1>;
- };
-
- uart_A: serial@84c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84c0 0x0 0x14>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- uart_B: serial@84dc {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x84dc 0x0 0x14>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- uart_C: serial@8700 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x8700 0x0 0x14>;
- interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
-
- watchdog@98d0 {
- compatible = "amlogic,meson-gxbb-wdt";
- reg = <0x0 0x098d0 0x0 0x10>;
- clocks = <&xtal>;
- };
- };
-
- gic: interrupt-controller@c4301000 {
- compatible = "arm,gic-400";
- reg = <0x0 0xc4301000 0 0x1000>,
- <0x0 0xc4302000 0 0x2000>,
- <0x0 0xc4304000 0 0x2000>,
- <0x0 0xc4306000 0 0x2000>;
- interrupt-controller;
- interrupts = <GIC_PPI 9
- (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
- #interrupt-cells = <3>;
- #address-cells = <0>;
- };
-
- aobus: aobus@c8100000 {
- compatible = "simple-bus";
- reg = <0x0 0xc8100000 0x0 0x100000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xc8100000 0x0 0x100000>;
-
- pinctrl_aobus: pinctrl@14 {
- compatible = "amlogic,meson-gxbb-aobus-pinctrl";
- #address-cells = <2>;
- #size-cells = <2>;
- ranges;
-
- gpio_ao: bank@14 {
- reg = <0x0 0x00014 0x0 0x8>,
- <0x0 0x0002c 0x0 0x4>,
- <0x0 0x00024 0x0 0x8>;
- reg-names = "mux", "pull", "gpio";
- gpio-controller;
- #gpio-cells = <2>;
- };
-
- uart_ao_a_pins: uart_ao_a {
- mux {
- groups = "uart_tx_ao_a", "uart_rx_ao_a";
- function = "uart_ao";
- };
- };
- };
-
- clkc_AO: clock-controller@040 {
- compatible = "amlogic,gxbb-aoclkc";
- reg = <0x0 0x00040 0x0 0x4>;
- #clock-cells = <1>;
- #reset-cells = <1>;
- };
-
- uart_AO: serial@4c0 {
- compatible = "amlogic,meson-uart";
- reg = <0x0 0x004c0 0x0 0x14>;
- interrupts = <GIC_SPI 193 IRQ_TYPE_EDGE_RISING>;
- clocks = <&xtal>;
- status = "disabled";
- };
- };
-
periphs: periphs@c8834000 {
compatible = "simple-bus";
reg = <0x0 0xc8834000 0x0 0x2000>;
@@ -340,47 +161,6 @@
};
};
- apb: apb@d0000000 {
- compatible = "simple-bus";
- reg = <0x0 0xd0000000 0x0 0x200000>;
- #address-cells = <2>;
- #size-cells = <2>;
- ranges = <0x0 0x0 0x0 0xd0000000 0x0 0x200000>;
-
- sd_emmc_a: mmc@70000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x70000 0x0 0x2000>;
- interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_A>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
-
- sd_emmc_b: mmc@72000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x72000 0x0 0x2000>;
- interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_B>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
-
- sd_emmc_c: mmc@74000 {
- compatible = "amlogic,meson-gxbb-mmc";
- reg = <0x0 0x74000 0x0 0x2000>;
- interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
- clocks = <&clkc CLKID_SD_EMMC_C>,
- <&xtal>,
- <&clkc CLKID_FCLK_DIV2>;
- clock-names = "core", "clkin0", "clkin1";
- status = "disabled";
- };
- };
-
ethmac: ethernet@c9410000 {
compatible = "amlogic,meson6-dwmac", "snps,dwmac";
reg = <0x0 0xc9410000 0x0 0x10000
@@ -394,3 +174,101 @@
};
};
};
+
+&cbus {
+ reset: reset-controller@4404 {
+ compatible = "amlogic,meson-gxbb-reset";
+ reg = <0x0 0x04404 0x0 0x20>;
+ #reset-cells = <1>;
+ };
+
+ uart_B: serial@84dc {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x84dc 0x0 0x14>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ uart_C: serial@8700 {
+ compatible = "amlogic,meson-uart";
+ reg = <0x0 0x8700 0x0 0x14>;
+ interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&xtal>;
+ status = "disabled";
+ };
+
+ watchdog@98d0 {
+ compatible = "amlogic,meson-gxbb-wdt";
+ reg = <0x0 0x098d0 0x0 0x10>;
+ clocks = <&xtal>;
+ };
+};
+
+&aobus {
+ pinctrl_aobus: pinctrl@14 {
+ compatible = "amlogic,meson-gxbb-aobus-pinctrl";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ gpio_ao: bank@14 {
+ reg = <0x0 0x00014 0x0 0x8>,
+ <0x0 0x0002c 0x0 0x4>,
+ <0x0 0x00024 0x0 0x8>;
+ reg-names = "mux", "pull", "gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ uart_ao_a_pins: uart_ao_a {
+ mux {
+ groups = "uart_tx_ao_a", "uart_rx_ao_a";
+ function = "uart_ao";
+ };
+ };
+ };
+
+ clkc_AO: clock-controller@040 {
+ compatible = "amlogic,gxbb-aoclkc";
+ reg = <0x0 0x00040 0x0 0x4>;
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+};
+
+&apb {
+ sd_emmc_a: mmc@70000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x70000 0x0 0x2000>;
+ interrupts = <GIC_SPI 216 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_A>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+
+ sd_emmc_b: mmc@72000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x72000 0x0 0x2000>;
+ interrupts = <GIC_SPI 217 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_B>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+
+ sd_emmc_c: mmc@74000 {
+ compatible = "amlogic,meson-gxbb-mmc";
+ reg = <0x0 0x74000 0x0 0x2000>;
+ interrupts = <GIC_SPI 218 IRQ_TYPE_EDGE_RISING>;
+ clocks = <&clkc CLKID_SD_EMMC_C>,
+ <&xtal>,
+ <&clkc CLKID_FCLK_DIV2>;
+ clock-names = "core", "clkin0", "clkin1";
+ status = "disabled";
+ };
+};
+
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2016-08-29 7:56 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-08-29 7:56 [RFC PATCH 0/3] ARm64: amlogic: Introduce common GX family dtsi Neil Armstrong
2016-08-29 7:56 ` [RFC PATCH 1/3] ARM64: dts: amlogic: Add Meson GX Family common dtsi Neil Armstrong
2016-08-29 7:56 ` [RFC PATCH 2/3] ARM64: dts: amlogic: Switch Meson GXL dtsi to use common GX dtsi Neil Armstrong
[not found] ` <1472457371-1305-1-git-send-email-narmstrong-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
2016-08-29 7:56 ` Neil Armstrong [this message]
2016-08-29 8:01 ` [RFC PATCH 0/3] ARm64: amlogic: Introduce common GX family dtsi Carlo Caione
[not found] ` <CAOQ7t2YGbASh7v25wgDspKNWgFOcRsikJs_WZptn+LkVXmaHig-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-08-29 18:38 ` Andreas Färber
2016-08-29 19:50 ` Carlo Caione
2016-08-29 20:15 ` Andreas Färber
[not found] ` <ca513cb4-34d4-72f9-9e32-7908329243a6-l3A5Bk7waGM@public.gmane.org>
2016-08-30 8:33 ` Neil Armstrong
2016-08-31 19:32 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1472457371-1305-4-git-send-email-narmstrong@baylibre.com \
--to=narmstrong-rdvid1duhrbwk0htik3j/w@public.gmane.org \
--cc=carlo-KA+7E9HrN00dnm+yROfE0A@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=khilman-rdvid1DuHRBWk0Htik3J/w@public.gmane.org \
--cc=linux-amlogic-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).