From: Sinan Kaya <okaya@codeaurora.org>
To: dmaengine@vger.kernel.org, timur@codeaurora.org,
devicetree@vger.kernel.org, cov@codeaurora.org,
vinod.koul@intel.com, jcm@redhat.com
Cc: agross@codeaurora.org, arnd@arndb.de,
linux-arm-msm@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
Sinan Kaya <okaya@codeaurora.org>,
Dan Williams <dan.j.williams@intel.com>,
linux-kernel@vger.kernel.org
Subject: [PATCH V3 07/10] dmaengine: qcom_hidma: bring out interrupt cause
Date: Thu, 15 Sep 2016 13:22:43 -0400 [thread overview]
Message-ID: <1473960166-30155-8-git-send-email-okaya@codeaurora.org> (raw)
In-Reply-To: <1473960166-30155-1-git-send-email-okaya@codeaurora.org>
Bring out the interrupt cause to the top level so that MSI interrupts
can be hooked at a later stage.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
---
drivers/dma/qcom/hidma_ll.c | 72 +++++++++++++++++++++------------------------
1 file changed, 34 insertions(+), 38 deletions(-)
diff --git a/drivers/dma/qcom/hidma_ll.c b/drivers/dma/qcom/hidma_ll.c
index c911ca2..088935f 100644
--- a/drivers/dma/qcom/hidma_ll.c
+++ b/drivers/dma/qcom/hidma_ll.c
@@ -397,12 +397,24 @@ static int hidma_ll_reset(struct hidma_lldev *lldev)
* requests traditionally to the destination, this concept does not apply
* here for this HW.
*/
-irqreturn_t hidma_ll_inthandler(int chirq, void *arg)
+static void hidma_ll_int_handler_internal(struct hidma_lldev *lldev, int cause)
{
- struct hidma_lldev *lldev = arg;
- u32 status;
- u32 enable;
- u32 cause;
+ if (cause & HIDMA_ERR_INT_MASK) {
+ dev_err(lldev->dev, "error 0x%x, disabling...\n",
+ cause);
+
+ /* Clear out pending interrupts */
+ writel(cause, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
+
+ /* No further submissions. */
+ hidma_ll_disable(lldev);
+
+ /* Driver completes the txn and intimates the client.*/
+ hidma_cleanup_pending_tre(lldev, 0xFF,
+ HIDMA_EVRE_STATUS_ERROR);
+
+ return;
+ }
/*
* Fine tuned for this HW...
@@ -412,45 +424,29 @@ irqreturn_t hidma_ll_inthandler(int chirq, void *arg)
* interrupt delivery guarantees. Do not copy this code blindly and
* expect that to work.
*/
- status = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_STAT_REG);
- enable = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_EN_REG);
- cause = status & enable;
-
- while (cause) {
- if (cause & HIDMA_ERR_INT_MASK) {
- dev_err(lldev->dev, "error 0x%x, disabling...\n",
- cause);
-
- /* Clear out pending interrupts */
- writel(cause, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
-
- /* No further submissions. */
- hidma_ll_disable(lldev);
-
- /* Driver completes the txn and intimates the client.*/
- hidma_cleanup_pending_tre(lldev, 0xFF,
- HIDMA_EVRE_STATUS_ERROR);
- goto out;
- }
-
+ while (atomic_read(&lldev->pending_tre_count)) {
/*
* Try to consume as many EVREs as possible.
*/
- hidma_handle_tre_completion(lldev);
+ if (hidma_handle_tre_completion(lldev, 0, 0))
+ break;
+ }
- /* We consumed TREs or there are pending TREs or EVREs. */
- writel_relaxed(cause, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
+ /* We consumed TREs or there are pending TREs or EVREs. */
+ writel_relaxed(cause, lldev->evca + HIDMA_EVCA_IRQ_CLR_REG);
+}
- /*
- * Another interrupt might have arrived while we are
- * processing this one. Read the new cause.
- */
- status = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_STAT_REG);
- enable = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_EN_REG);
- cause = status & enable;
- }
+irqreturn_t hidma_ll_inthandler(int chirq, void *arg)
+{
+ struct hidma_lldev *lldev = arg;
+ u32 status;
+ u32 enable;
+ u32 cause;
-out:
+ status = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_STAT_REG);
+ enable = readl_relaxed(lldev->evca + HIDMA_EVCA_IRQ_EN_REG);
+ cause = status & enable;
+ hidma_ll_int_handler_internal(lldev, cause);
return IRQ_HANDLED;
}
--
1.9.1
next prev parent reply other threads:[~2016-09-15 17:22 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-09-15 17:22 [PATCH V3 00/10] dmaengine: qcom_hidma: add MSI interrupt support Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 01/10] Documentation: DT: qcom_hidma: update binding for MSI Sinan Kaya
2016-09-23 15:39 ` Rob Herring
2016-09-23 17:22 ` Sinan Kaya
[not found] ` <1473960166-30155-2-git-send-email-okaya-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-09-23 18:02 ` Mark Rutland
2016-09-23 18:58 ` Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 02/10] Documentation: DT: qcom_hidma: correct spelling mistakes Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 03/10] of: irq: make of_msi_configure accessible from modules Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 04/10] dmaengine: qcom_hidma: configure DMA and MSI for OF Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 05/10] dmaengine: qcom_hidma: make pending_tre_count atomic Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 06/10] dmaengine: qcom_hidma: make error and success path common Sinan Kaya
2016-09-15 17:22 ` Sinan Kaya [this message]
2016-09-15 17:22 ` [PATCH V3 08/10] dmaengine: qcom_hidma: add a common API to setup the interrupt Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 09/10] dmaengine: qcom_hidma: protect common data structures Sinan Kaya
2016-09-15 17:22 ` [PATCH V3 10/10] dmaengine: qcom_hidma: add MSI support for interrupts Sinan Kaya
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1473960166-30155-8-git-send-email-okaya@codeaurora.org \
--to=okaya@codeaurora.org \
--cc=agross@codeaurora.org \
--cc=arnd@arndb.de \
--cc=cov@codeaurora.org \
--cc=dan.j.williams@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=dmaengine@vger.kernel.org \
--cc=jcm@redhat.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=timur@codeaurora.org \
--cc=vinod.koul@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).