From: Tomasz Figa <t.figa@samsung.com>
To: Kukjin Kim <kgene.kim@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>,
linux-samsung-soc@vger.kernel.org,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>
Subject: Re: [PATCH v2] ARM: dts: Add regulator entries to Exynos5420 SMDK board
Date: Wed, 18 Dec 2013 16:18:22 +0100 [thread overview]
Message-ID: <1476645.Pay9pLa8zo@amdc1227> (raw)
In-Reply-To: <52A635BF.9030102@samsung.com>
Hi Kukjin,
On Tuesday 10 of December 2013 06:27:27 Kukjin Kim wrote:
> On 12/05/13 18:44, Sachin Kamat wrote:
> > Added regulator entries to Exynos5420 SMDK board.
> >
> > Signed-off-by: Sachin Kamat<sachin.kamat@linaro.org>
> > ---
> > Changes since v1:
> > Changed node name
> > ---
> > arch/arm/boot/dts/exynos5420-smdk5420.dts | 216 +++++++++++++++++++++++++++++
> > 1 file changed, 216 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > index fb5a1e25c632..62e1ebe4e989 100644
> > --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
> > @@ -120,4 +120,220 @@
> > reg =<0x50>;
> > };
> > };
> > +
> > + hsi2c_4: i2c@12CA0000 {
> > + status = "okay";
> > +
> > + s2mps11_pmic@66 {
> > + compatible = "samsung,s2mps11-pmic";
> > + reg =<0x66>;
> > + s2mps11,buck2-ramp-delay =<12>;
> > + s2mps11,buck34-ramp-delay =<12>;
> > + s2mps11,buck16-ramp-delay =<12>;
> > + s2mps11,buck6-ramp-enable =<1>;
> > + s2mps11,buck2-ramp-enable =<1>;
> > + s2mps11,buck3-ramp-enable =<1>;
> > + s2mps11,buck4-ramp-enable =<1>;
> > +
> > + s2mps11_osc: clocks {
> > + #clock-cells =<1>;
> > + clock-output-names = "s2mps11_ap",
> > + "s2mps11_cp", "s2mps11_bt";
> > + };
> > +
> > + regulators {
> > + ldo1_reg: LDO1 {
> > + regulator-name = "vdd_ldo1";
> > + regulator-min-microvolt =<1000000>;
> > + regulator-max-microvolt =<1000000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo3_reg: LDO3 {
> > + regulator-name = "vdd_ldo3";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo5_reg: LDO5 {
> > + regulator-name = "vdd_ldo5";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo6_reg: LDO6 {
> > + regulator-name = "vdd_ldo6";
> > + regulator-min-microvolt =<1000000>;
> > + regulator-max-microvolt =<1000000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo7_reg: LDO7 {
> > + regulator-name = "vdd_ldo7";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo8_reg: LDO8 {
> > + regulator-name = "vdd_ldo8";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo9_reg: LDO9 {
> > + regulator-name = "vdd_ldo9";
> > + regulator-min-microvolt =<3000000>;
> > + regulator-max-microvolt =<3000000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo10_reg: LDO10 {
> > + regulator-name = "vdd_ldo10";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo11_reg: LDO11 {
> > + regulator-name = "vdd_ldo11";
> > + regulator-min-microvolt =<1000000>;
> > + regulator-max-microvolt =<1000000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo12_reg: LDO12 {
> > + regulator-name = "vdd_ldo12";
> > + regulator-min-microvolt =<1800000>;
> > + regulator-max-microvolt =<1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo13_reg: LDO13 {
> > + regulator-name = "vdd_ldo13";
> > + regulator-min-microvolt =<2800000>;
> > + regulator-max-microvolt =<2800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo15_reg: LDO15 {
> > + regulator-name = "vdd_ldo15";
> > + regulator-min-microvolt =<3100000>;
> > + regulator-max-microvolt =<3100000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo16_reg: LDO16 {
> > + regulator-name = "vdd_ldo16";
> > + regulator-min-microvolt =<2200000>;
> > + regulator-max-microvolt =<2200000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo17_reg: LDO17 {
> > + regulator-name = "tsp_avdd";
> > + regulator-min-microvolt =<3300000>;
> > + regulator-max-microvolt =<3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo19_reg: LDO19 {
> > + regulator-name = "vdd_sd";
> > + regulator-min-microvolt =<2800000>;
> > + regulator-max-microvolt =<2800000>;
> > + regulator-always-on;
> > + };
> > +
> > + ldo24_reg: LDO24 {
> > + regulator-name = "tsp_io";
> > + regulator-min-microvolt =<2800000>;
> > + regulator-max-microvolt =<2800000>;
> > + regulator-always-on;
> > + };
> > +
> > + buck1_reg: BUCK1 {
> > + regulator-name = "vdd_mif";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1300000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck2_reg: BUCK2 {
> > + regulator-name = "vdd_arm";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck3_reg: BUCK3 {
> > + regulator-name = "vdd_int";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1400000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck4_reg: BUCK4 {
> > + regulator-name = "vdd_g3d";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1400000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck5_reg: BUCK5 {
> > + regulator-name = "vdd_mem";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1400000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck6_reg: BUCK6 {
> > + regulator-name = "vdd_kfc";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck7_reg: BUCK7 {
> > + regulator-name = "vdd_1.0v_ldo";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck8_reg: BUCK8 {
> > + regulator-name = "vdd_1.8v_ldo";
> > + regulator-min-microvolt =<800000>;
> > + regulator-max-microvolt =<1500000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck9_reg: BUCK9 {
> > + regulator-name = "vdd_2.8v_ldo";
> > + regulator-min-microvolt =<3000000>;
> > + regulator-max-microvolt =<3750000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > +
> > + buck10_reg: BUCK10 {
> > + regulator-name = "vdd_vmem";
> > + regulator-min-microvolt =<2850000>;
> > + regulator-max-microvolt =<2850000>;
> > + regulator-always-on;
> > + regulator-boot-on;
> > + };
> > + };
> > + };
> > + };
> > };
>
> just + DT ml.
AFAIK, current recommendation after the KS is that changes touching only
DTS files don't have to be posted on DT ML. Just changes related to DT
bindings such as Documentation/devicetree and DT parsing code. Full series
doing both still need to be posted there, though.
Best regards,
Tomasz
prev parent reply other threads:[~2013-12-18 15:18 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <1386236664-27763-1-git-send-email-sachin.kamat@linaro.org>
2013-12-09 21:27 ` [PATCH v2] ARM: dts: Add regulator entries to Exynos5420 SMDK board Kukjin Kim
2013-12-18 15:18 ` Tomasz Figa [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1476645.Pay9pLa8zo@amdc1227 \
--to=t.figa@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=kgene.kim@samsung.com \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=sachin.kamat@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox