From: Bartosz Golaszewski <bgolaszewski@baylibre.com>
To: Kevin Hilman <khilman@baylibre.com>,
Michael Turquette <mturquette@baylibre.com>,
Sekhar Nori <nsekhar@ti.com>, Rob Herring <robh+dt@kernel.org>,
Frank Rowand <frowand.list@gmail.com>,
Mark Rutland <mark.rutland@arm.com>,
Peter Ujfalusi <peter.ujfalusi@ti.com>,
Russell King <linux@armlinux.org.uk>
Cc: linux-devicetree <devicetree@vger.kernel.org>,
LKML <linux-kernel@vger.kernel.org>,
linux-drm <dri-devel@lists.freedesktop.org>,
Bartosz Golaszewski <bgolaszewski@baylibre.com>,
Tomi Valkeinen <tomi.valkeinen@ti.com>,
Jyri Sarha <jsarha@ti.com>,
arm-soc <linux-arm-kernel@lists.infradead.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Subject: [PATCH 1/2] ARM: memory: da8xx-ddrctl: new driver
Date: Wed, 26 Oct 2016 19:35:54 +0200 [thread overview]
Message-ID: <1477503355-2600-2-git-send-email-bgolaszewski@baylibre.com> (raw)
In-Reply-To: <1477503355-2600-1-git-send-email-bgolaszewski@baylibre.com>
Create a new driver for the da8xx DDR2/mDDR controller and implement
support for writing to the Peripheral Bus Burst Priority Register.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
---
.../memory-controllers/ti-da8xx-ddrctl.txt | 20 +++
drivers/memory/Kconfig | 8 +
drivers/memory/Makefile | 1 +
drivers/memory/da8xx-ddrctl.c | 175 +++++++++++++++++++++
4 files changed, 204 insertions(+)
create mode 100644 Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt
create mode 100644 drivers/memory/da8xx-ddrctl.c
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt
new file mode 100644
index 0000000..7e271dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt
@@ -0,0 +1,20 @@
+* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller
+
+The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features
+a set of registers which allow to tweak the controller's behavior.
+
+Documentation:
+OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
+
+Required properties:
+
+- compatible: "ti,da850-ddr-controller" - for da850 SoC based boards
+- reg: a tuple containing the base address of the memory
+ controller and the size of the memory area to map
+
+Example for da850 shown below.
+
+ddrctl {
+ compatible = "ti,da850-ddr-controller";
+ reg = <0xB0000000 0x100>;
+};
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 4b4c0c3..ec80e35 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -134,6 +134,14 @@ config MTK_SMI
mainly help enable/disable iommu and control the power domain and
clocks for each local arbiter.
+config DA8XX_DDRCTL
+ bool "Texas Instruments da8xx DDR2/mDDR driver"
+ depends on ARCH_DAVINCI_DA8XX
+ help
+ This driver is for the DDR2/mDDR Memory Controller present on
+ Texas Instruments da8xx SoCs. It's used to tweak various memory
+ controller configuration options.
+
source "drivers/memory/samsung/Kconfig"
source "drivers/memory/tegra/Kconfig"
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index b20ae38..e88097fb 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_MVEBU_DEVBUS) += mvebu-devbus.o
obj-$(CONFIG_TEGRA20_MC) += tegra20-mc.o
obj-$(CONFIG_JZ4780_NEMC) += jz4780-nemc.o
obj-$(CONFIG_MTK_SMI) += mtk-smi.o
+obj-$(CONFIG_DA8XX_DDRCTL) += da8xx-ddrctl.o
obj-$(CONFIG_SAMSUNG_MC) += samsung/
obj-$(CONFIG_TEGRA_MC) += tegra/
diff --git a/drivers/memory/da8xx-ddrctl.c b/drivers/memory/da8xx-ddrctl.c
new file mode 100644
index 0000000..900e131
--- /dev/null
+++ b/drivers/memory/da8xx-ddrctl.c
@@ -0,0 +1,175 @@
+/*
+ * TI da8xx DDR2/mDDR controller driver
+ *
+ * Copyright (C) 2016 BayLibre SAS
+ *
+ * Author:
+ * Bartosz Golaszewski <bgolaszewski@baylibre.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_fdt.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+
+/*
+ * REVISIT: Linux doesn't have a good framework for the kind of performance
+ * knobs this driver controls. We can't use device tree properties as it deals
+ * with hardware configuration rather than description. We also don't want to
+ * commit to maintaining some random sysfs attributes.
+ *
+ * For now we just hardcode the register values for the boards that need
+ * some changes (as is the case for the LCD controller on da850-lcdk - the
+ * first board we support here). When linux gets an appropriate framework,
+ * we'll easily convert the driver to it.
+ */
+
+struct da8xx_ddrctl_config_knob {
+ const char *name;
+ u32 reg;
+ u32 mask;
+ u32 shift;
+};
+
+static const struct da8xx_ddrctl_config_knob da8xx_ddrctl_knobs[] = {
+ {
+ .name = "da850-pbbpr",
+ .reg = 0x20,
+ .mask = 0xffffff00,
+ .shift = 0,
+ },
+};
+
+struct da8xx_ddrctl_setting {
+ const char *name;
+ u32 val;
+};
+
+struct da8xx_ddrctl_board_settings {
+ const char *board;
+ const struct da8xx_ddrctl_setting *settings;
+};
+
+static const struct da8xx_ddrctl_setting da850_lcdk_ddrctl_settings[] = {
+ {
+ .name = "da850-pbbpr",
+ .val = 0x20,
+ },
+ { }
+};
+
+static const struct da8xx_ddrctl_board_settings da8xx_ddrctl_board_confs[] = {
+ {
+ .board = "ti,da850-lcdk",
+ .settings = da850_lcdk_ddrctl_settings,
+ },
+};
+
+static const struct da8xx_ddrctl_config_knob *
+da8xx_ddrctl_match_knob(const struct da8xx_ddrctl_setting *setting)
+{
+ const struct da8xx_ddrctl_config_knob *knob;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(da8xx_ddrctl_knobs); i++) {
+ knob = &da8xx_ddrctl_knobs[i];
+
+ if (strcmp(knob->name, setting->name) == 0)
+ return knob;
+ }
+
+ return NULL;
+}
+
+static const struct da8xx_ddrctl_setting *da8xx_ddrctl_get_board_settings(void)
+{
+ const struct da8xx_ddrctl_board_settings *board_settings;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(da8xx_ddrctl_board_confs); i++) {
+ board_settings = &da8xx_ddrctl_board_confs[i];
+
+ if (of_machine_is_compatible(board_settings->board))
+ return board_settings->settings;
+ }
+
+ return NULL;
+}
+
+static int da8xx_ddrctl_probe(struct platform_device *pdev)
+{
+ const struct da8xx_ddrctl_config_knob *knob;
+ const struct da8xx_ddrctl_setting *setting;
+ struct device_node *node;
+ struct resource *res;
+ void __iomem *ddrctl;
+ struct device *dev;
+ u32 reg;
+
+ dev = &pdev->dev;
+ node = dev->of_node;
+
+ setting = da8xx_ddrctl_get_board_settings();
+ if (!setting) {
+ dev_err(dev, "no settings for board '%s'\n",
+ of_flat_dt_get_machine_name());
+ return -EINVAL;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ddrctl = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ddrctl)) {
+ dev_err(dev, "unable to map memory controller registers\n");
+ return PTR_ERR(ddrctl);
+ }
+
+ for (; setting->name; setting++) {
+ knob = da8xx_ddrctl_match_knob(setting);
+ if (!knob) {
+ dev_warn(dev,
+ "no such config option: %s\n", setting->name);
+ continue;
+ }
+
+ if (knob->reg > (res->end - res->start - sizeof(u32))) {
+ dev_warn(dev,
+ "register offset of '%s' exceeds mapped memory size\n",
+ knob->name);
+ continue;
+ }
+
+ reg = __raw_readl(ddrctl + knob->reg);
+ reg &= knob->mask;
+ reg |= setting->val << knob->shift;
+
+ dev_dbg(dev, "writing 0x%08x to %s\n", reg, setting->name);
+
+ __raw_writel(reg, ddrctl + knob->reg);
+ }
+
+ return 0;
+}
+
+static const struct of_device_id da8xx_ddrctl_of_match[] = {
+ { .compatible = "ti,da850-ddr-controller", },
+ { },
+};
+
+static struct platform_driver da8xx_ddrctl_driver = {
+ .probe = da8xx_ddrctl_probe,
+ .driver = {
+ .name = "da850-ddr-controller",
+ .of_match_table = da8xx_ddrctl_of_match,
+ },
+};
+module_platform_driver(da8xx_ddrctl_driver);
+
+MODULE_AUTHOR("Bartosz Golaszewski <bgolaszewski@baylibre.com>");
+MODULE_DESCRIPTION("TI da8xx DDR2/mDDR controller driver");
+MODULE_LICENSE("GPL v2");
--
2.9.3
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2016-10-26 17:35 UTC|newest]
Thread overview: 11+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-10-26 17:35 [PATCH 0/2] ARM: da850: new drivers for better LCDC support Bartosz Golaszewski
2016-10-26 17:35 ` Bartosz Golaszewski [this message]
[not found] ` <1477503355-2600-2-git-send-email-bgolaszewski-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
2016-10-27 16:55 ` [PATCH 1/2] ARM: memory: da8xx-ddrctl: new driver Kevin Hilman
2016-10-31 4:27 ` Rob Herring
2016-10-26 17:35 ` [PATCH 2/2] ARM: bus: da8xx-mstpri: " Bartosz Golaszewski
2016-10-31 4:30 ` Rob Herring
2016-10-31 9:40 ` Bartosz Golaszewski
[not found] ` <CAMpxmJW85TQObLdoGW2ApnkM8OiM4d1ZDd=9eyGmeVXXwqByPQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-10-31 9:52 ` Sekhar Nori
2016-10-31 9:54 ` Bartosz Golaszewski
[not found] ` <CAMpxmJX7SjE1zs926Fn-=jsZhPsOK6ey0hHM8LBhNS1nuSuFFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2016-10-31 10:31 ` Sekhar Nori
[not found] ` <0d5d1e41-b8e6-5d60-6da1-5b6ddd9bc07e-l0cyMroinI0@public.gmane.org>
2016-10-31 18:22 ` Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1477503355-2600-2-git-send-email-bgolaszewski@baylibre.com \
--to=bgolaszewski@baylibre.com \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=frowand.list@gmail.com \
--cc=jsarha@ti.com \
--cc=khilman@baylibre.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux@armlinux.org.uk \
--cc=mark.rutland@arm.com \
--cc=mturquette@baylibre.com \
--cc=nsekhar@ti.com \
--cc=peter.ujfalusi@ti.com \
--cc=robh+dt@kernel.org \
--cc=tomi.valkeinen@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).