* [PATCH 1/3] ARM: imx6u: add imx6ull support
[not found] ` <1477969343-19887-1-git-send-email-peter.chen-3arQi8VN3Tc@public.gmane.org>
@ 2016-11-01 3:02 ` Peter Chen
[not found] ` <1477969343-19887-2-git-send-email-peter.chen-3arQi8VN3Tc@public.gmane.org>
2016-11-01 3:02 ` [PATCH 2/3] ARM: imx: mach-imx6ul: " Peter Chen
2016-11-01 3:02 ` [PATCH 3/3] clk: imx: clk-imx6ul: add clk support for imx6ull Peter Chen
2 siblings, 1 reply; 13+ messages in thread
From: Peter Chen @ 2016-11-01 3:02 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
mturquette-rdvid1DuHRBWk0Htik3J/w
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, fabio.estevam-3arQi8VN3Tc,
mark.rutland-5wv7dgnIgG8, linux-clk-u79uwXL29TY76Z2rM5mHXA,
Peter Chen
It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:
http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL
In this patch, it moves common dts between imx6ul* and imx6ull* as
new files named imx6u*, and the specific part for imx6ul and imx6ull
are individual file.
Signed-off-by: Peter Chen <peter.chen-3arQi8VN3Tc@public.gmane.org>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/imx6u-14x14-evk.dts | 475 ++++++++++++++++
arch/arm/boot/dts/imx6u-14x14-evk.dtsi | 487 +++++++++++++++++
arch/arm/boot/dts/imx6u.dtsi | 942 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/imx6ul-14x14-evk.dts | 479 +---------------
arch/arm/boot/dts/imx6ul.dtsi | 936 +------------------------------
arch/arm/boot/dts/imx6ull-14x14-evk.dts | 17 +
arch/arm/boot/dts/imx6ull-pinfunc.h | 57 ++
arch/arm/boot/dts/imx6ull.dtsi | 10 +
9 files changed, 1993 insertions(+), 1413 deletions(-)
create mode 100644 arch/arm/boot/dts/imx6u-14x14-evk.dts
create mode 100644 arch/arm/boot/dts/imx6u-14x14-evk.dtsi
create mode 100644 arch/arm/boot/dts/imx6u.dtsi
create mode 100644 arch/arm/boot/dts/imx6ull-14x14-evk.dts
create mode 100644 arch/arm/boot/dts/imx6ull-pinfunc.h
create mode 100644 arch/arm/boot/dts/imx6ull.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd26..3d6e199 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -423,7 +423,8 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
imx6ul-pico-hobbit.dtb \
imx6ul-tx6ul-0010.dtb \
imx6ul-tx6ul-0011.dtb \
- imx6ul-tx6ul-mainboard.dtb
+ imx6ul-tx6ul-mainboard.dtb \
+ imx6ull-14x14-evk.dtb
dtb-$(CONFIG_SOC_IMX7D) += \
imx7d-cl-som-imx7.dtb \
imx7d-colibri-eval-v3.dtb \
diff --git a/arch/arm/boot/dts/imx6u-14x14-evk.dts b/arch/arm/boot/dts/imx6u-14x14-evk.dts
new file mode 100644
index 0000000..ba8614c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6u-14x14-evk.dts
@@ -0,0 +1,475 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6ul.dtsi"
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_sd1_vmmc: sd1_regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "mx6ul-wm8960";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In",
+ "Line", "Line Out",
+ "Speaker", "Speaker",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Speaker", "SPK_LP",
+ "Speaker", "SPK_LN",
+ "Speaker", "SPK_RP",
+ "Speaker", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "LINPUT3", "Mic Jack",
+ "RINPUT1", "Mic Jack",
+ "RINPUT2", "Mic Jack";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clks IMX6UL_CLK_SAI2>;
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <786432000>;
+};
+
+&cpu0 {
+ arm-supply = <®_arm>;
+ soc-supply = <®_soc>;
+};
+
+&i2c2 {
+ clock_frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ codec: wm8960@1a {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ wlf,shared-lrclk;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: n25q256a@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a";
+ spi-max-frequency = <29000000>;
+ reg = <0>;
+ };
+};
+
+&sai2 {
+ assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+ <&clks IMX6UL_CLK_SAI2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <0>, <12288000>;
+ fsl,sai-mclk-direction-output;
+ status = "disabled";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&tsc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ measure-delay-time = <0xffff>;
+ pre-charge-time = <0xfff>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
+ MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
+ MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
+ MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
+ MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
+ MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
+ MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
+ MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
+ MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
+ MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
+ MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
+ MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp{
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp{
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ /* used for lcd reset */
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_sim2: sim2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808
+ MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31
+ MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808
+ MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808
+ MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809
+ MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */
+ MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6u-14x14-evk.dtsi b/arch/arm/boot/dts/imx6u-14x14-evk.dtsi
new file mode 100644
index 0000000..c80a214
--- /dev/null
+++ b/arch/arm/boot/dts/imx6u-14x14-evk.dtsi
@@ -0,0 +1,487 @@
+/*
+ * Copyright (C) 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+ chosen {
+ stdout-path = &uart1;
+ };
+
+ memory {
+ reg = <0x80000000 0x20000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reg_sd1_vmmc: sd1_regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "VSD_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "mx6ul-wm8960";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,bitclock-master = <&dailink_master>;
+ simple-audio-card,frame-master = <&dailink_master>;
+ simple-audio-card,widgets =
+ "Microphone", "Mic Jack",
+ "Line", "Line In",
+ "Line", "Line Out",
+ "Speaker", "Speaker",
+ "Headphone", "Headphone Jack";
+ simple-audio-card,routing =
+ "Headphone Jack", "HP_L",
+ "Headphone Jack", "HP_R",
+ "Speaker", "SPK_LP",
+ "Speaker", "SPK_LN",
+ "Speaker", "SPK_RP",
+ "Speaker", "SPK_RN",
+ "LINPUT1", "Mic Jack",
+ "LINPUT3", "Mic Jack",
+ "RINPUT1", "Mic Jack",
+ "RINPUT2", "Mic Jack";
+
+ simple-audio-card,cpu {
+ sound-dai = <&sai2>;
+ };
+
+ dailink_master: simple-audio-card,codec {
+ sound-dai = <&codec>;
+ clocks = <&clks IMX6UL_CLK_SAI2>;
+ };
+ };
+};
+
+&clks {
+ assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <786432000>;
+};
+
+&cpu0 {
+ arm-supply = <®_arm>;
+ soc-supply = <®_soc>;
+};
+
+&i2c2 {
+ clock_frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+
+ codec: wm8960@1a {
+ #sound-dai-cells = <0>;
+ compatible = "wlf,wm8960";
+ reg = <0x1a>;
+ wlf,shared-lrclk;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy0>;
+ status = "okay";
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ };
+ };
+};
+
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+ display = <&display0>;
+ status = "okay";
+
+ display0: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+
+ timing0: timing0 {
+ clock-frequency = <9200000>;
+ hactive = <480>;
+ vactive = <272>;
+ hfront-porch = <8>;
+ hback-porch = <4>;
+ hsync-len = <41>;
+ vback-porch = <2>;
+ vfront-porch = <4>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ flash0: n25q256a@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q256a";
+ spi-max-frequency = <29000000>;
+ reg = <0>;
+ };
+};
+
+&sai2 {
+ assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
+ <&clks IMX6UL_CLK_SAI2>;
+ assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+ assigned-clock-rates = <0>, <12288000>;
+ fsl,sai-mclk-direction-output;
+ status = "disabled";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&tsc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_tsc>;
+ xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
+ measure-delay-time = <0xffff>;
+ pre-charge-time = <0xfff>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usbphy1 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usbphy2 {
+ fsl,tx-d-cal = <106>;
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ no-1-8-v;
+ keep-power-in-suspend;
+ wakeup-source;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
+ MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
+ MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
+ MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
+ MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
+ MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
+ MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
+ MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
+ MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
+ MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
+ MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
+ MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x17059
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp{
+ fsl,pins = <
+ MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
+ MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp{
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
+ MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ /* used for lcd reset */
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_sim2: sim2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808
+ MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31
+ MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808
+ MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808
+ MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809
+ MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008
+ >;
+ };
+
+ pinctrl_tsc: tscgrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1
+ MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */
+ MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */
+ MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
+
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6u.dtsi b/arch/arm/boot/dts/imx6u.dtsi
new file mode 100644
index 0000000..c5c05fd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6u.dtsi
@@ -0,0 +1,942 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <dt-bindings/clock/imx6ul-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx6ul-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+ aliases {
+ ethernet0 = &fec1;
+ ethernet1 = &fec2;
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ serial6 = &uart7;
+ serial7 = &uart8;
+ sai1 = &sai1;
+ sai2 = &sai2;
+ sai3 = &sai3;
+ spi0 = &ecspi1;
+ spi1 = &ecspi2;
+ spi2 = &ecspi3;
+ spi3 = &ecspi4;
+ usbphy0 = &usbphy1;
+ usbphy1 = &usbphy2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ clock-latency = <61036>; /* two CLK32 periods */
+ operating-points = <
+ /* kHz uV */
+ 528000 1175000
+ 396000 1025000
+ 198000 950000
+ >;
+ fsl,soc-operating-points = <
+ /* KHz uV */
+ 528000 1175000
+ 396000 1175000
+ 198000 1175000
+ >;
+ clocks = <&clks IMX6UL_CLK_ARM>,
+ <&clks IMX6UL_CLK_PLL2_BUS>,
+ <&clks IMX6UL_CLK_PLL2_PFD2>,
+ <&clks IMX6UL_CA7_SECONDARY_SEL>,
+ <&clks IMX6UL_CLK_STEP>,
+ <&clks IMX6UL_CLK_PLL1_SW>,
+ <&clks IMX6UL_CLK_PLL1_SYS>,
+ <&clks IMX6UL_PLL1_BYPASS>,
+ <&clks IMX6UL_CLK_PLL1>,
+ <&clks IMX6UL_PLL1_BYPASS_SRC>,
+ <&clks IMX6UL_CLK_OSC>;
+ clock-names = "arm", "pll2_bus", "pll2_pfd2_396m",
+ "secondary_sel", "step", "pll1_sw",
+ "pll1_sys", "pll1_bypass", "pll1",
+ "pll1_bypass_src", "osc";
+ arm-supply = <®_arm>;
+ soc-supply = <®_soc>;
+ };
+ };
+
+ intc: interrupt-controller@00a01000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x00a01000 0x1000>,
+ <0x00a02000 0x1000>,
+ <0x00a04000 0x2000>,
+ <0x00a06000 0x2000>;
+ };
+
+ ckil: clock-cli {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "ckil";
+ };
+
+ osc: clock-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc";
+ };
+
+ ipp_di0: clock-di0 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "ipp_di0";
+ };
+
+ ipp_di1: clock-di1 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <0>;
+ clock-output-names = "ipp_di1";
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&gpc>;
+ ranges;
+
+ pmu {
+ compatible = "arm,cortex-a7-pmu";
+ interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
+ ocram: sram@00900000 {
+ compatible = "mmio-sram";
+ reg = <0x00900000 0x20000>;
+ };
+
+ dma_apbh: dma-apbh@01804000 {
+ compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
+ reg = <0x01804000 0x2000>;
+ interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>,
+ <0 13 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
+ #dma-cells = <1>;
+ dma-channels = <4>;
+ clocks = <&clks IMX6UL_CLK_APBHDMA>;
+ };
+
+ gpmi: gpmi-nand@01806000 {
+ compatible = "fsl,imx6q-gpmi-nand";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x01806000 0x2000>, <0x01808000 0x2000>;
+ reg-names = "gpmi-nand", "bch";
+ interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "bch";
+ clocks = <&clks IMX6UL_CLK_GPMI_IO>,
+ <&clks IMX6UL_CLK_GPMI_APB>,
+ <&clks IMX6UL_CLK_GPMI_BCH>,
+ <&clks IMX6UL_CLK_GPMI_BCH_APB>,
+ <&clks IMX6UL_CLK_PER_BCH>;
+ clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
+ "gpmi_bch_apb", "per1_bch";
+ dmas = <&dma_apbh 0>;
+ dma-names = "rx-tx";
+ status = "disabled";
+ };
+
+ aips1: aips-bus@02000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x100000>;
+ ranges;
+
+ spba-bus@02000000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x40000>;
+ ranges;
+
+ ecspi1: ecspi@02008000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02008000 0x4000>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ECSPI1>,
+ <&clks IMX6UL_CLK_ECSPI1>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi2: ecspi@0200c000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+ reg = <0x0200c000 0x4000>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ECSPI2>,
+ <&clks IMX6UL_CLK_ECSPI2>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi3: ecspi@02010000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02010000 0x4000>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ECSPI3>,
+ <&clks IMX6UL_CLK_ECSPI3>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ ecspi4: ecspi@02014000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02014000 0x4000>;
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ECSPI4>,
+ <&clks IMX6UL_CLK_ECSPI4>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart7: serial@02018000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x02018000 0x4000>;
+ interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART7_IPG>,
+ <&clks IMX6UL_CLK_UART7_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart1: serial@02020000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x02020000 0x4000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART1_IPG>,
+ <&clks IMX6UL_CLK_UART1_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart8: serial@02024000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x02024000 0x4000>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART8_IPG>,
+ <&clks IMX6UL_CLK_UART8_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ sai1: sai@02028000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
+ reg = <0x02028000 0x4000>;
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_SAI1_IPG>,
+ <&clks IMX6UL_CLK_SAI1>,
+ <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma 35 24 0>,
+ <&sdma 36 24 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai2: sai@0202c000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
+ reg = <0x0202c000 0x4000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_SAI2_IPG>,
+ <&clks IMX6UL_CLK_SAI2>,
+ <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma 37 24 0>,
+ <&sdma 38 24 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ sai3: sai@02030000 {
+ #sound-dai-cells = <0>;
+ compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
+ reg = <0x02030000 0x4000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_SAI3_IPG>,
+ <&clks IMX6UL_CLK_SAI3>,
+ <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
+ clock-names = "bus", "mclk1", "mclk2", "mclk3";
+ dmas = <&sdma 39 24 0>,
+ <&sdma 40 24 0>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+ };
+
+ tsc: tsc@02040000 {
+ compatible = "fsl,imx6ul-tsc";
+ reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_IPG>,
+ <&clks IMX6UL_CLK_ADC2>;
+ clock-names = "tsc", "adc";
+ status = "disabled";
+ };
+
+ pwm1: pwm@02080000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x02080000 0x4000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM1>,
+ <&clks IMX6UL_CLK_PWM1>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@02084000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x02084000 0x4000>;
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM2>,
+ <&clks IMX6UL_CLK_PWM2>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@02088000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x02088000 0x4000>;
+ interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM3>,
+ <&clks IMX6UL_CLK_PWM3>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm@0208c000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x0208c000 0x4000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM4>,
+ <&clks IMX6UL_CLK_PWM4>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ can1: flexcan@02090000 {
+ compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x02090000 0x4000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_CAN1_IPG>,
+ <&clks IMX6UL_CLK_CAN1_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ can2: flexcan@02094000 {
+ compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x02094000 0x4000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_CAN2_IPG>,
+ <&clks IMX6UL_CLK_CAN2_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt1: gpt@02098000 {
+ compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
+ reg = <0x02098000 0x4000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_GPT1_BUS>,
+ <&clks IMX6UL_CLK_GPT1_SERIAL>;
+ clock-names = "ipg", "per";
+ };
+
+ gpio1: gpio@0209c000 {
+ compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+ reg = <0x0209c000 0x4000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 23 10>, <&iomuxc 10 17 6>,
+ <&iomuxc 16 33 16>;
+ };
+
+ gpio2: gpio@020a0000 {
+ compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+ reg = <0x020a0000 0x4000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 49 16>, <&iomuxc 16 111 6>;
+ };
+
+ gpio3: gpio@020a4000 {
+ compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+ reg = <0x020a4000 0x4000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 65 29>;
+ };
+
+ gpio4: gpio@020a8000 {
+ compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+ reg = <0x020a8000 0x4000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 94 17>, <&iomuxc 17 117 12>;
+ };
+
+ gpio5: gpio@020ac000 {
+ compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
+ reg = <0x020ac000 0x4000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ gpio-ranges = <&iomuxc 0 7 10>, <&iomuxc 10 5 2>;
+ };
+
+ fec2: ethernet@020b4000 {
+ compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
+ reg = <0x020b4000 0x4000>;
+ interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ENET>,
+ <&clks IMX6UL_CLK_ENET_AHB>,
+ <&clks IMX6UL_CLK_ENET_PTP>,
+ <&clks IMX6UL_CLK_ENET2_REF_125M>,
+ <&clks IMX6UL_CLK_ENET2_REF_125M>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<1>;
+ fsl,num-rx-queues=<1>;
+ status = "disabled";
+ };
+
+ kpp: kpp@020b8000 {
+ compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
+ reg = <0x020b8000 0x4000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_KPP>;
+ status = "disabled";
+ };
+
+ wdog1: wdog@020bc000 {
+ compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
+ reg = <0x020bc000 0x4000>;
+ interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_WDOG1>;
+ };
+
+ wdog2: wdog@020c0000 {
+ compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
+ reg = <0x020c0000 0x4000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_WDOG2>;
+ status = "disabled";
+ };
+
+ clks: ccm@020c4000 {
+ compatible = "fsl,imx6ul-ccm";
+ reg = <0x020c4000 0x4000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <1>;
+ clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
+ clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
+ };
+
+ anatop: anatop@020c8000 {
+ compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
+ "syscon", "simple-bus";
+ reg = <0x020c8000 0x1000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+
+ reg_3p0: regulator-3p0 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd3p0";
+ regulator-min-microvolt = <2625000>;
+ regulator-max-microvolt = <3400000>;
+ anatop-reg-offset = <0x120>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <0>;
+ anatop-min-voltage = <2625000>;
+ anatop-max-voltage = <3400000>;
+ anatop-enable-bit = <0>;
+ };
+
+ reg_arm: regulator-vddcore {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "cpu";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <0>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <24>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+
+ reg_soc: regulator-vddsoc {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vddsoc";
+ regulator-min-microvolt = <725000>;
+ regulator-max-microvolt = <1450000>;
+ regulator-always-on;
+ anatop-reg-offset = <0x140>;
+ anatop-vol-bit-shift = <18>;
+ anatop-vol-bit-width = <5>;
+ anatop-delay-reg-offset = <0x170>;
+ anatop-delay-bit-shift = <28>;
+ anatop-delay-bit-width = <2>;
+ anatop-min-bit-val = <1>;
+ anatop-min-voltage = <725000>;
+ anatop-max-voltage = <1450000>;
+ };
+ };
+
+ usbphy1: usbphy@020c9000 {
+ compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020c9000 0x1000>;
+ interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USBPHY1>;
+ phy-3p0-supply = <®_3p0>;
+ fsl,anatop = <&anatop>;
+ };
+
+ usbphy2: usbphy@020ca000 {
+ compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
+ reg = <0x020ca000 0x1000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USBPHY2>;
+ phy-3p0-supply = <®_3p0>;
+ fsl,anatop = <&anatop>;
+ };
+
+ snvs: snvs@020cc000 {
+ compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+ reg = <0x020cc000 0x4000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ snvs_poweroff: snvs-poweroff {
+ compatible = "syscon-poweroff";
+ regmap = <&snvs>;
+ offset = <0x38>;
+ mask = <0x60>;
+ status = "disabled";
+ };
+
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ epit1: epit@020d0000 {
+ reg = <0x020d0000 0x4000>;
+ interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ epit2: epit@020d4000 {
+ reg = <0x020d4000 0x4000>;
+ interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ src: src@020d8000 {
+ compatible = "fsl,imx6ul-src", "fsl,imx51-src";
+ reg = <0x020d8000 0x4000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+
+ gpc: gpc@020dc000 {
+ compatible = "fsl,imx6ul-gpc", "fsl,imx6q-gpc";
+ reg = <0x020dc000 0x4000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-parent = <&intc>;
+ };
+
+ iomuxc: iomuxc@020e0000 {
+ compatible = "fsl,imx6ul-iomuxc";
+ reg = <0x020e0000 0x4000>;
+ };
+
+ gpr: iomuxc-gpr@020e4000 {
+ compatible = "fsl,imx6ul-iomuxc-gpr",
+ "fsl,imx6q-iomuxc-gpr", "syscon";
+ reg = <0x020e4000 0x4000>;
+ };
+
+ gpt2: gpt@020e8000 {
+ compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
+ reg = <0x020e8000 0x4000>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_GPT2_BUS>,
+ <&clks IMX6UL_CLK_GPT2_SERIAL>;
+ clock-names = "ipg", "per";
+ };
+
+ sdma: sdma@020ec000 {
+ compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
+ "fsl,imx35-sdma";
+ reg = <0x020ec000 0x4000>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_SDMA>,
+ <&clks IMX6UL_CLK_SDMA>;
+ clock-names = "ipg", "ahb";
+ #dma-cells = <3>;
+ fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
+ };
+
+ pwm5: pwm@020f0000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x020f0000 0x4000>;
+ interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM5>,
+ <&clks IMX6UL_CLK_PWM5>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm6: pwm@020f4000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x020f4000 0x4000>;
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM6>,
+ <&clks IMX6UL_CLK_PWM6>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm7: pwm@020f8000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x020f8000 0x4000>;
+ interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM7>,
+ <&clks IMX6UL_CLK_PWM7>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm8: pwm@020fc000 {
+ compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
+ reg = <0x020fc000 0x4000>;
+ interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_PWM8>,
+ <&clks IMX6UL_CLK_PWM8>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+ };
+
+ aips2: aips-bus@02100000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02100000 0x100000>;
+ ranges;
+
+ usbotg1: usb@02184000 {
+ compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
+ reg = <0x02184000 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy1>;
+ fsl,usbmisc = <&usbmisc 0>;
+ fsl,anatop = <&anatop>;
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbotg2: usb@02184200 {
+ compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
+ reg = <0x02184200 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USBOH3>;
+ fsl,usbphy = <&usbphy2>;
+ fsl,usbmisc = <&usbmisc 1>;
+ ahb-burst-config = <0x0>;
+ tx-burst-size-dword = <0x10>;
+ rx-burst-size-dword = <0x10>;
+ status = "disabled";
+ };
+
+ usbmisc: usbmisc@02184800 {
+ #index-cells = <1>;
+ compatible = "fsl,imx6ul-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x02184800 0x200>;
+ };
+
+ fec1: ethernet@02188000 {
+ compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
+ reg = <0x02188000 0x4000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ENET>,
+ <&clks IMX6UL_CLK_ENET_AHB>,
+ <&clks IMX6UL_CLK_ENET_PTP>,
+ <&clks IMX6UL_CLK_ENET_REF>,
+ <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<1>;
+ fsl,num-rx-queues=<1>;
+ status = "disabled";
+ };
+
+ usdhc1: usdhc@02190000 {
+ compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
+ reg = <0x02190000 0x4000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USDHC1>,
+ <&clks IMX6UL_CLK_USDHC1>,
+ <&clks IMX6UL_CLK_USDHC1>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: usdhc@02194000 {
+ compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
+ reg = <0x02194000 0x4000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_USDHC2>,
+ <&clks IMX6UL_CLK_USDHC2>,
+ <&clks IMX6UL_CLK_USDHC2>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ adc1: adc@02198000 {
+ compatible = "fsl,imx6ul-adc", "fsl,vf610-adc";
+ reg = <0x02198000 0x4000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_ADC1>;
+ num-channels = <2>;
+ clock-names = "adc";
+ fsl,adck-max-frequency = <30000000>, <40000000>,
+ <20000000>;
+ status = "disabled";
+ };
+
+ i2c1: i2c@021a0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+ reg = <0x021a0000 0x4000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_I2C1>;
+ status = "disabled";
+ };
+
+ i2c2: i2c@021a4000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+ reg = <0x021a4000 0x4000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_I2C2>;
+ status = "disabled";
+ };
+
+ i2c3: i2c@021a8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+ reg = <0x021a8000 0x4000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_I2C3>;
+ status = "disabled";
+ };
+
+ mmdc: mmdc@021b0000 {
+ compatible = "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc";
+ reg = <0x021b0000 0x4000>;
+ };
+
+ lcdif: lcdif@021c8000 {
+ compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
+ reg = <0x021c8000 0x4000>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
+ <&clks IMX6UL_CLK_LCDIF_APB>,
+ <&clks IMX6UL_CLK_DUMMY>;
+ clock-names = "pix", "axi", "disp_axi";
+ status = "disabled";
+ };
+
+ qspi: qspi@021e0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+ reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
+ reg-names = "QuadSPI", "QuadSPI-memory";
+ interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_QSPI>,
+ <&clks IMX6UL_CLK_QSPI>;
+ clock-names = "qspi_en", "qspi";
+ status = "disabled";
+ };
+
+ uart2: serial@021e8000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x021e8000 0x4000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART2_IPG>,
+ <&clks IMX6UL_CLK_UART2_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart3: serial@021ec000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x021ec000 0x4000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART3_IPG>,
+ <&clks IMX6UL_CLK_UART3_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart4: serial@021f0000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x021f0000 0x4000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART4_IPG>,
+ <&clks IMX6UL_CLK_UART4_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart5: serial@021f4000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x021f4000 0x4000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART5_IPG>,
+ <&clks IMX6UL_CLK_UART5_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ i2c4: i2c@021f8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
+ reg = <0x021f8000 0x4000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_I2C4>;
+ status = "disabled";
+ };
+
+ uart6: serial@021fc000 {
+ compatible = "fsl,imx6ul-uart",
+ "fsl,imx6q-uart";
+ reg = <0x021fc000 0x4000>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6UL_CLK_UART6_IPG>,
+ <&clks IMX6UL_CLK_UART6_SERIAL>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dts b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
index 1867c69..f423f0c 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dts
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dts
@@ -9,486 +9,9 @@
/dts-v1/;
#include "imx6ul.dtsi"
+#include "imx6u-14x14-evk.dtsi"
/ {
model = "Freescale i.MX6 UltraLite 14x14 EVK Board";
compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul";
-
- chosen {
- stdout-path = &uart1;
- };
-
- memory {
- reg = <0x80000000 0x20000000>;
- };
-
- backlight {
- compatible = "pwm-backlight";
- pwms = <&pwm1 0 5000000>;
- brightness-levels = <0 4 8 16 32 64 128 255>;
- default-brightness-level = <6>;
- status = "okay";
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
-
- reg_sd1_vmmc: sd1_regulator {
- compatible = "regulator-fixed";
- regulator-name = "VSD_3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
- };
-
- sound {
- compatible = "simple-audio-card";
- simple-audio-card,name = "mx6ul-wm8960";
- simple-audio-card,format = "i2s";
- simple-audio-card,bitclock-master = <&dailink_master>;
- simple-audio-card,frame-master = <&dailink_master>;
- simple-audio-card,widgets =
- "Microphone", "Mic Jack",
- "Line", "Line In",
- "Line", "Line Out",
- "Speaker", "Speaker",
- "Headphone", "Headphone Jack";
- simple-audio-card,routing =
- "Headphone Jack", "HP_L",
- "Headphone Jack", "HP_R",
- "Speaker", "SPK_LP",
- "Speaker", "SPK_LN",
- "Speaker", "SPK_RP",
- "Speaker", "SPK_RN",
- "LINPUT1", "Mic Jack",
- "LINPUT3", "Mic Jack",
- "RINPUT1", "Mic Jack",
- "RINPUT2", "Mic Jack";
-
- simple-audio-card,cpu {
- sound-dai = <&sai2>;
- };
-
- dailink_master: simple-audio-card,codec {
- sound-dai = <&codec>;
- clocks = <&clks IMX6UL_CLK_SAI2>;
- };
- };
-};
-
-&clks {
- assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
- assigned-clock-rates = <786432000>;
-};
-
-&cpu0 {
- arm-supply = <®_arm>;
- soc-supply = <®_soc>;
-};
-
-&i2c2 {
- clock_frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c2>;
- status = "okay";
-
- codec: wm8960@1a {
- #sound-dai-cells = <0>;
- compatible = "wlf,wm8960";
- reg = <0x1a>;
- wlf,shared-lrclk;
- };
-};
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet1>;
- phy-mode = "rmii";
- phy-handle = <ðphy0>;
- status = "okay";
-};
-
-&fec2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet2>;
- phy-mode = "rmii";
- phy-handle = <ðphy1>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy0: ethernet-phy@2 {
- reg = <2>;
- };
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- };
- };
-};
-
-
-&lcdif {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_lcdif_dat
- &pinctrl_lcdif_ctrl>;
- display = <&display0>;
- status = "okay";
-
- display0: display {
- bits-per-pixel = <16>;
- bus-width = <24>;
-
- display-timings {
- native-mode = <&timing0>;
-
- timing0: timing0 {
- clock-frequency = <9200000>;
- hactive = <480>;
- vactive = <272>;
- hfront-porch = <8>;
- hback-porch = <4>;
- hsync-len = <41>;
- vback-porch = <2>;
- vfront-porch = <4>;
- vsync-len = <10>;
- hsync-active = <0>;
- vsync-active = <0>;
- de-active = <1>;
- pixelclk-active = <0>;
- };
- };
- };
-};
-
-&pwm1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm1>;
- status = "okay";
-};
-
-&qspi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_qspi>;
- status = "okay";
-
- flash0: n25q256a@0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "micron,n25q256a";
- spi-max-frequency = <29000000>;
- reg = <0>;
- };
-};
-
-&sai2 {
- assigned-clocks = <&clks IMX6UL_CLK_SAI2_SEL>,
- <&clks IMX6UL_CLK_SAI2>;
- assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
- assigned-clock-rates = <0>, <12288000>;
- fsl,sai-mclk-direction-output;
- status = "disabled";
-};
-
-&snvs_poweroff {
- status = "okay";
-};
-
-&tsc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_tsc>;
- xnur-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
- measure-delay-time = <0xffff>;
- pre-charge-time = <0xfff>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- uart-has-rtscts;
- status = "okay";
-};
-
-&usbotg1 {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usbotg2 {
- dr_mode = "host";
- disable-over-current;
- status = "okay";
-};
-
-&usbphy1 {
- fsl,tx-d-cal = <106>;
-};
-
-&usbphy2 {
- fsl,tx-d-cal = <106>;
-};
-
-&usdhc1 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc1>;
- pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
- cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
- keep-power-in-suspend;
- wakeup-source;
- vmmc-supply = <®_sd1_vmmc>;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc2>;
- no-1-8-v;
- keep-power-in-suspend;
- wakeup-source;
- status = "okay";
-};
-
-&wdog1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- fsl,ext-reset-output;
-};
-
-&iomuxc {
- pinctrl-names = "default";
-
- pinctrl_csi1: csi1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_MCLK__CSI_MCLK 0x1b088
- MX6UL_PAD_CSI_PIXCLK__CSI_PIXCLK 0x1b088
- MX6UL_PAD_CSI_VSYNC__CSI_VSYNC 0x1b088
- MX6UL_PAD_CSI_HSYNC__CSI_HSYNC 0x1b088
- MX6UL_PAD_CSI_DATA00__CSI_DATA02 0x1b088
- MX6UL_PAD_CSI_DATA01__CSI_DATA03 0x1b088
- MX6UL_PAD_CSI_DATA02__CSI_DATA04 0x1b088
- MX6UL_PAD_CSI_DATA03__CSI_DATA05 0x1b088
- MX6UL_PAD_CSI_DATA04__CSI_DATA06 0x1b088
- MX6UL_PAD_CSI_DATA05__CSI_DATA07 0x1b088
- MX6UL_PAD_CSI_DATA06__CSI_DATA08 0x1b088
- MX6UL_PAD_CSI_DATA07__CSI_DATA09 0x1b088
- >;
- };
-
- pinctrl_enet1: enet1grp {
- fsl,pins = <
- MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
- MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b031
- >;
- };
-
- pinctrl_enet2: enet2grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
- MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
- MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b031
- MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x17059
- >;
- };
-
- pinctrl_flexcan1: flexcan1grp{
- fsl,pins = <
- MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX 0x1b020
- MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX 0x1b020
- >;
- };
-
- pinctrl_flexcan2: flexcan2grp{
- fsl,pins = <
- MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
- MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0
- MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0
- >;
- };
-
- pinctrl_i2c2: i2c2grp {
- fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
- MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
- >;
- };
-
- pinctrl_lcdif_dat: lcdifdatgrp {
- fsl,pins = <
- MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
- MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
- MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
- MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
- MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
- MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
- MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
- MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
- MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
- MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
- MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
- MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
- MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
- MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
- MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
- MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
- MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
- MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
- MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
- MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
- MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
- MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
- MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
- MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
- >;
- };
-
- pinctrl_lcdif_ctrl: lcdifctrlgrp {
- fsl,pins = <
- MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
- MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
- MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
- MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
- /* used for lcd reset */
- MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x79
- >;
- };
-
- pinctrl_qspi: qspigrp {
- fsl,pins = <
- MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
- MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
- MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
- MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
- MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
- MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
- >;
- };
-
- pinctrl_pwm1: pwm1grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO08__PWM1_OUT 0x110b0
- >;
- };
-
- pinctrl_sim2: sim2grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA03__SIM2_PORT1_PD 0xb808
- MX6UL_PAD_CSI_DATA04__SIM2_PORT1_CLK 0x31
- MX6UL_PAD_CSI_DATA05__SIM2_PORT1_RST_B 0xb808
- MX6UL_PAD_CSI_DATA06__SIM2_PORT1_SVEN 0xb808
- MX6UL_PAD_CSI_DATA07__SIM2_PORT1_TRXD 0xb809
- MX6UL_PAD_CSI_DATA02__GPIO4_IO23 0x3008
- >;
- };
-
- pinctrl_tsc: tscgrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO01__GPIO1_IO01 0xb0
- MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
- MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
- MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0xb0
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
- MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX 0x1b0b1
- MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX 0x1b0b1
- MX6UL_PAD_UART3_RX_DATA__UART2_DCE_RTS 0x1b0b1
- MX6UL_PAD_UART3_TX_DATA__UART2_DCE_CTS 0x1b0b1
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
- MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x17059 /* SD1 CD */
- MX6UL_PAD_GPIO1_IO05__USDHC1_VSELECT 0x17059 /* SD1 VSELECT */
- MX6UL_PAD_GPIO1_IO09__GPIO1_IO09 0x17059 /* SD1 RESET */
- >;
- };
-
- pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170b9
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100b9
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170b9
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170b9
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170b9
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170b9
-
- >;
- };
-
- pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x170f9
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x100f9
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x170f9
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x170f9
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x170f9
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x170f9
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x17059
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
- >;
- };
-
- pinctrl_wdog: wdoggrp {
- fsl,pins = <
- MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY 0x30b0
- >;
- };
};
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index c5c05fd..e3952c5 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -1,942 +1,10 @@
/*
- * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2016 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
-#include <dt-bindings/clock/imx6ul-clock.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx6u.dtsi"
#include "imx6ul-pinfunc.h"
-#include "skeleton.dtsi"
-
-/ {
- aliases {
- ethernet0 = &fec1;
- ethernet1 = &fec2;
- gpio0 = &gpio1;
- gpio1 = &gpio2;
- gpio2 = &gpio3;
- gpio3 = &gpio4;
- gpio4 = &gpio5;
- i2c0 = &i2c1;
- i2c1 = &i2c2;
- i2c2 = &i2c3;
- i2c3 = &i2c4;
- mmc0 = &usdhc1;
- mmc1 = &usdhc2;
- serial0 = &uart1;
- serial1 = &uart2;
- serial2 = &uart3;
- serial3 = &uart4;
- serial4 = &uart5;
- serial5 = &uart6;
- serial6 = &uart7;
- serial7 = &uart8;
- sai1 = &sai1;
- sai2 = &sai2;
- sai3 = &sai3;
- spi0 = &ecspi1;
- spi1 = &ecspi2;
- spi2 = &ecspi3;
- spi3 = &ecspi4;
- usbphy0 = &usbphy1;
- usbphy1 = &usbphy2;
- };
-
- cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu@0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- clock-latency = <61036>; /* two CLK32 periods */
- operating-points = <
- /* kHz uV */
- 528000 1175000
- 396000 1025000
- 198000 950000
- >;
- fsl,soc-operating-points = <
- /* KHz uV */
- 528000 1175000
- 396000 1175000
- 198000 1175000
- >;
- clocks = <&clks IMX6UL_CLK_ARM>,
- <&clks IMX6UL_CLK_PLL2_BUS>,
- <&clks IMX6UL_CLK_PLL2_PFD2>,
- <&clks IMX6UL_CA7_SECONDARY_SEL>,
- <&clks IMX6UL_CLK_STEP>,
- <&clks IMX6UL_CLK_PLL1_SW>,
- <&clks IMX6UL_CLK_PLL1_SYS>,
- <&clks IMX6UL_PLL1_BYPASS>,
- <&clks IMX6UL_CLK_PLL1>,
- <&clks IMX6UL_PLL1_BYPASS_SRC>,
- <&clks IMX6UL_CLK_OSC>;
- clock-names = "arm", "pll2_bus", "pll2_pfd2_396m",
- "secondary_sel", "step", "pll1_sw",
- "pll1_sys", "pll1_bypass", "pll1",
- "pll1_bypass_src", "osc";
- arm-supply = <®_arm>;
- soc-supply = <®_soc>;
- };
- };
-
- intc: interrupt-controller@00a01000 {
- compatible = "arm,cortex-a7-gic";
- #interrupt-cells = <3>;
- interrupt-controller;
- reg = <0x00a01000 0x1000>,
- <0x00a02000 0x1000>,
- <0x00a04000 0x2000>,
- <0x00a06000 0x2000>;
- };
-
- ckil: clock-cli {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- clock-output-names = "ckil";
- };
-
- osc: clock-osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- clock-output-names = "osc";
- };
-
- ipp_di0: clock-di0 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <0>;
- clock-output-names = "ipp_di0";
- };
-
- ipp_di1: clock-di1 {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <0>;
- clock-output-names = "ipp_di1";
- };
-
- soc {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- interrupt-parent = <&gpc>;
- ranges;
-
- pmu {
- compatible = "arm,cortex-a7-pmu";
- interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- };
-
- ocram: sram@00900000 {
- compatible = "mmio-sram";
- reg = <0x00900000 0x20000>;
- };
-
- dma_apbh: dma-apbh@01804000 {
- compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh";
- reg = <0x01804000 0x2000>;
- interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>,
- <0 13 IRQ_TYPE_LEVEL_HIGH>,
- <0 13 IRQ_TYPE_LEVEL_HIGH>,
- <0 13 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3";
- #dma-cells = <1>;
- dma-channels = <4>;
- clocks = <&clks IMX6UL_CLK_APBHDMA>;
- };
-
- gpmi: gpmi-nand@01806000 {
- compatible = "fsl,imx6q-gpmi-nand";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x01806000 0x2000>, <0x01808000 0x2000>;
- reg-names = "gpmi-nand", "bch";
- interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "bch";
- clocks = <&clks IMX6UL_CLK_GPMI_IO>,
- <&clks IMX6UL_CLK_GPMI_APB>,
- <&clks IMX6UL_CLK_GPMI_BCH>,
- <&clks IMX6UL_CLK_GPMI_BCH_APB>,
- <&clks IMX6UL_CLK_PER_BCH>;
- clock-names = "gpmi_io", "gpmi_apb", "gpmi_bch",
- "gpmi_bch_apb", "per1_bch";
- dmas = <&dma_apbh 0>;
- dma-names = "rx-tx";
- status = "disabled";
- };
-
- aips1: aips-bus@02000000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x02000000 0x100000>;
- ranges;
-
- spba-bus@02000000 {
- compatible = "fsl,spba-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x02000000 0x40000>;
- ranges;
-
- ecspi1: ecspi@02008000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
- reg = <0x02008000 0x4000>;
- interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ECSPI1>,
- <&clks IMX6UL_CLK_ECSPI1>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- ecspi2: ecspi@0200c000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
- reg = <0x0200c000 0x4000>;
- interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ECSPI2>,
- <&clks IMX6UL_CLK_ECSPI2>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- ecspi3: ecspi@02010000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
- reg = <0x02010000 0x4000>;
- interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ECSPI3>,
- <&clks IMX6UL_CLK_ECSPI3>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- ecspi4: ecspi@02014000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi";
- reg = <0x02014000 0x4000>;
- interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ECSPI4>,
- <&clks IMX6UL_CLK_ECSPI4>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart7: serial@02018000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x02018000 0x4000>;
- interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART7_IPG>,
- <&clks IMX6UL_CLK_UART7_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart1: serial@02020000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x02020000 0x4000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART1_IPG>,
- <&clks IMX6UL_CLK_UART1_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart8: serial@02024000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x02024000 0x4000>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART8_IPG>,
- <&clks IMX6UL_CLK_UART8_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- sai1: sai@02028000 {
- #sound-dai-cells = <0>;
- compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
- reg = <0x02028000 0x4000>;
- interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_SAI1_IPG>,
- <&clks IMX6UL_CLK_SAI1>,
- <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
- clock-names = "bus", "mclk1", "mclk2", "mclk3";
- dmas = <&sdma 35 24 0>,
- <&sdma 36 24 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- sai2: sai@0202c000 {
- #sound-dai-cells = <0>;
- compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
- reg = <0x0202c000 0x4000>;
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_SAI2_IPG>,
- <&clks IMX6UL_CLK_SAI2>,
- <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
- clock-names = "bus", "mclk1", "mclk2", "mclk3";
- dmas = <&sdma 37 24 0>,
- <&sdma 38 24 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- sai3: sai@02030000 {
- #sound-dai-cells = <0>;
- compatible = "fsl,imx6ul-sai", "fsl,imx6sx-sai";
- reg = <0x02030000 0x4000>;
- interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_SAI3_IPG>,
- <&clks IMX6UL_CLK_SAI3>,
- <&clks IMX6UL_CLK_DUMMY>, <&clks IMX6UL_CLK_DUMMY>;
- clock-names = "bus", "mclk1", "mclk2", "mclk3";
- dmas = <&sdma 39 24 0>,
- <&sdma 40 24 0>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
- };
-
- tsc: tsc@02040000 {
- compatible = "fsl,imx6ul-tsc";
- reg = <0x02040000 0x4000>, <0x0219c000 0x4000>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_IPG>,
- <&clks IMX6UL_CLK_ADC2>;
- clock-names = "tsc", "adc";
- status = "disabled";
- };
-
- pwm1: pwm@02080000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x02080000 0x4000>;
- interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM1>,
- <&clks IMX6UL_CLK_PWM1>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm2: pwm@02084000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x02084000 0x4000>;
- interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM2>,
- <&clks IMX6UL_CLK_PWM2>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm3: pwm@02088000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x02088000 0x4000>;
- interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM3>,
- <&clks IMX6UL_CLK_PWM3>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm4: pwm@0208c000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x0208c000 0x4000>;
- interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM4>,
- <&clks IMX6UL_CLK_PWM4>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- can1: flexcan@02090000 {
- compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
- reg = <0x02090000 0x4000>;
- interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_CAN1_IPG>,
- <&clks IMX6UL_CLK_CAN1_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- can2: flexcan@02094000 {
- compatible = "fsl,imx6ul-flexcan", "fsl,imx6q-flexcan";
- reg = <0x02094000 0x4000>;
- interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_CAN2_IPG>,
- <&clks IMX6UL_CLK_CAN2_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- gpt1: gpt@02098000 {
- compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
- reg = <0x02098000 0x4000>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_GPT1_BUS>,
- <&clks IMX6UL_CLK_GPT1_SERIAL>;
- clock-names = "ipg", "per";
- };
-
- gpio1: gpio@0209c000 {
- compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
- reg = <0x0209c000 0x4000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 23 10>, <&iomuxc 10 17 6>,
- <&iomuxc 16 33 16>;
- };
-
- gpio2: gpio@020a0000 {
- compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
- reg = <0x020a0000 0x4000>;
- interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 49 16>, <&iomuxc 16 111 6>;
- };
-
- gpio3: gpio@020a4000 {
- compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
- reg = <0x020a4000 0x4000>;
- interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 65 29>;
- };
-
- gpio4: gpio@020a8000 {
- compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
- reg = <0x020a8000 0x4000>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 94 17>, <&iomuxc 17 117 12>;
- };
-
- gpio5: gpio@020ac000 {
- compatible = "fsl,imx6ul-gpio", "fsl,imx35-gpio";
- reg = <0x020ac000 0x4000>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- gpio-ranges = <&iomuxc 0 7 10>, <&iomuxc 10 5 2>;
- };
-
- fec2: ethernet@020b4000 {
- compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
- reg = <0x020b4000 0x4000>;
- interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ENET>,
- <&clks IMX6UL_CLK_ENET_AHB>,
- <&clks IMX6UL_CLK_ENET_PTP>,
- <&clks IMX6UL_CLK_ENET2_REF_125M>,
- <&clks IMX6UL_CLK_ENET2_REF_125M>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<1>;
- fsl,num-rx-queues=<1>;
- status = "disabled";
- };
-
- kpp: kpp@020b8000 {
- compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
- reg = <0x020b8000 0x4000>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_KPP>;
- status = "disabled";
- };
-
- wdog1: wdog@020bc000 {
- compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
- reg = <0x020bc000 0x4000>;
- interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_WDOG1>;
- };
-
- wdog2: wdog@020c0000 {
- compatible = "fsl,imx6ul-wdt", "fsl,imx21-wdt";
- reg = <0x020c0000 0x4000>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_WDOG2>;
- status = "disabled";
- };
-
- clks: ccm@020c4000 {
- compatible = "fsl,imx6ul-ccm";
- reg = <0x020c4000 0x4000>;
- interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
- #clock-cells = <1>;
- clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>;
- clock-names = "ckil", "osc", "ipp_di0", "ipp_di1";
- };
-
- anatop: anatop@020c8000 {
- compatible = "fsl,imx6ul-anatop", "fsl,imx6q-anatop",
- "syscon", "simple-bus";
- reg = <0x020c8000 0x1000>;
- interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
-
- reg_3p0: regulator-3p0 {
- compatible = "fsl,anatop-regulator";
- regulator-name = "vdd3p0";
- regulator-min-microvolt = <2625000>;
- regulator-max-microvolt = <3400000>;
- anatop-reg-offset = <0x120>;
- anatop-vol-bit-shift = <8>;
- anatop-vol-bit-width = <5>;
- anatop-min-bit-val = <0>;
- anatop-min-voltage = <2625000>;
- anatop-max-voltage = <3400000>;
- anatop-enable-bit = <0>;
- };
-
- reg_arm: regulator-vddcore {
- compatible = "fsl,anatop-regulator";
- regulator-name = "cpu";
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1450000>;
- regulator-always-on;
- anatop-reg-offset = <0x140>;
- anatop-vol-bit-shift = <0>;
- anatop-vol-bit-width = <5>;
- anatop-delay-reg-offset = <0x170>;
- anatop-delay-bit-shift = <24>;
- anatop-delay-bit-width = <2>;
- anatop-min-bit-val = <1>;
- anatop-min-voltage = <725000>;
- anatop-max-voltage = <1450000>;
- };
-
- reg_soc: regulator-vddsoc {
- compatible = "fsl,anatop-regulator";
- regulator-name = "vddsoc";
- regulator-min-microvolt = <725000>;
- regulator-max-microvolt = <1450000>;
- regulator-always-on;
- anatop-reg-offset = <0x140>;
- anatop-vol-bit-shift = <18>;
- anatop-vol-bit-width = <5>;
- anatop-delay-reg-offset = <0x170>;
- anatop-delay-bit-shift = <28>;
- anatop-delay-bit-width = <2>;
- anatop-min-bit-val = <1>;
- anatop-min-voltage = <725000>;
- anatop-max-voltage = <1450000>;
- };
- };
-
- usbphy1: usbphy@020c9000 {
- compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
- reg = <0x020c9000 0x1000>;
- interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USBPHY1>;
- phy-3p0-supply = <®_3p0>;
- fsl,anatop = <&anatop>;
- };
-
- usbphy2: usbphy@020ca000 {
- compatible = "fsl,imx6ul-usbphy", "fsl,imx23-usbphy";
- reg = <0x020ca000 0x1000>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USBPHY2>;
- phy-3p0-supply = <®_3p0>;
- fsl,anatop = <&anatop>;
- };
-
- snvs: snvs@020cc000 {
- compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
- reg = <0x020cc000 0x4000>;
-
- snvs_rtc: snvs-rtc-lp {
- compatible = "fsl,sec-v4.0-mon-rtc-lp";
- regmap = <&snvs>;
- offset = <0x34>;
- interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- snvs_poweroff: snvs-poweroff {
- compatible = "syscon-poweroff";
- regmap = <&snvs>;
- offset = <0x38>;
- mask = <0x60>;
- status = "disabled";
- };
-
- snvs_pwrkey: snvs-powerkey {
- compatible = "fsl,sec-v4.0-pwrkey";
- regmap = <&snvs>;
- interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
- linux,keycode = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- epit1: epit@020d0000 {
- reg = <0x020d0000 0x4000>;
- interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- epit2: epit@020d4000 {
- reg = <0x020d4000 0x4000>;
- interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- src: src@020d8000 {
- compatible = "fsl,imx6ul-src", "fsl,imx51-src";
- reg = <0x020d8000 0x4000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
- #reset-cells = <1>;
- };
-
- gpc: gpc@020dc000 {
- compatible = "fsl,imx6ul-gpc", "fsl,imx6q-gpc";
- reg = <0x020dc000 0x4000>;
- interrupt-controller;
- #interrupt-cells = <3>;
- interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-parent = <&intc>;
- };
-
- iomuxc: iomuxc@020e0000 {
- compatible = "fsl,imx6ul-iomuxc";
- reg = <0x020e0000 0x4000>;
- };
-
- gpr: iomuxc-gpr@020e4000 {
- compatible = "fsl,imx6ul-iomuxc-gpr",
- "fsl,imx6q-iomuxc-gpr", "syscon";
- reg = <0x020e4000 0x4000>;
- };
-
- gpt2: gpt@020e8000 {
- compatible = "fsl,imx6ul-gpt", "fsl,imx6sx-gpt";
- reg = <0x020e8000 0x4000>;
- interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_GPT2_BUS>,
- <&clks IMX6UL_CLK_GPT2_SERIAL>;
- clock-names = "ipg", "per";
- };
-
- sdma: sdma@020ec000 {
- compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
- "fsl,imx35-sdma";
- reg = <0x020ec000 0x4000>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_SDMA>,
- <&clks IMX6UL_CLK_SDMA>;
- clock-names = "ipg", "ahb";
- #dma-cells = <3>;
- fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin";
- };
-
- pwm5: pwm@020f0000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x020f0000 0x4000>;
- interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM5>,
- <&clks IMX6UL_CLK_PWM5>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm6: pwm@020f4000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x020f4000 0x4000>;
- interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM6>,
- <&clks IMX6UL_CLK_PWM6>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm7: pwm@020f8000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x020f8000 0x4000>;
- interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM7>,
- <&clks IMX6UL_CLK_PWM7>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm8: pwm@020fc000 {
- compatible = "fsl,imx6ul-pwm", "fsl,imx27-pwm";
- reg = <0x020fc000 0x4000>;
- interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_PWM8>,
- <&clks IMX6UL_CLK_PWM8>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
- };
-
- aips2: aips-bus@02100000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x02100000 0x100000>;
- ranges;
-
- usbotg1: usb@02184000 {
- compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
- reg = <0x02184000 0x200>;
- interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USBOH3>;
- fsl,usbphy = <&usbphy1>;
- fsl,usbmisc = <&usbmisc 0>;
- fsl,anatop = <&anatop>;
- ahb-burst-config = <0x0>;
- tx-burst-size-dword = <0x10>;
- rx-burst-size-dword = <0x10>;
- status = "disabled";
- };
-
- usbotg2: usb@02184200 {
- compatible = "fsl,imx6ul-usb", "fsl,imx27-usb";
- reg = <0x02184200 0x200>;
- interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USBOH3>;
- fsl,usbphy = <&usbphy2>;
- fsl,usbmisc = <&usbmisc 1>;
- ahb-burst-config = <0x0>;
- tx-burst-size-dword = <0x10>;
- rx-burst-size-dword = <0x10>;
- status = "disabled";
- };
-
- usbmisc: usbmisc@02184800 {
- #index-cells = <1>;
- compatible = "fsl,imx6ul-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x02184800 0x200>;
- };
-
- fec1: ethernet@02188000 {
- compatible = "fsl,imx6ul-fec", "fsl,imx6q-fec";
- reg = <0x02188000 0x4000>;
- interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ENET>,
- <&clks IMX6UL_CLK_ENET_AHB>,
- <&clks IMX6UL_CLK_ENET_PTP>,
- <&clks IMX6UL_CLK_ENET_REF>,
- <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<1>;
- fsl,num-rx-queues=<1>;
- status = "disabled";
- };
-
- usdhc1: usdhc@02190000 {
- compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
- reg = <0x02190000 0x4000>;
- interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USDHC1>,
- <&clks IMX6UL_CLK_USDHC1>,
- <&clks IMX6UL_CLK_USDHC1>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
-
- usdhc2: usdhc@02194000 {
- compatible = "fsl,imx6ul-usdhc", "fsl,imx6sx-usdhc";
- reg = <0x02194000 0x4000>;
- interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_USDHC2>,
- <&clks IMX6UL_CLK_USDHC2>,
- <&clks IMX6UL_CLK_USDHC2>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
-
- adc1: adc@02198000 {
- compatible = "fsl,imx6ul-adc", "fsl,vf610-adc";
- reg = <0x02198000 0x4000>;
- interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_ADC1>;
- num-channels = <2>;
- clock-names = "adc";
- fsl,adck-max-frequency = <30000000>, <40000000>,
- <20000000>;
- status = "disabled";
- };
-
- i2c1: i2c@021a0000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
- reg = <0x021a0000 0x4000>;
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_I2C1>;
- status = "disabled";
- };
-
- i2c2: i2c@021a4000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
- reg = <0x021a4000 0x4000>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_I2C2>;
- status = "disabled";
- };
-
- i2c3: i2c@021a8000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
- reg = <0x021a8000 0x4000>;
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_I2C3>;
- status = "disabled";
- };
-
- mmdc: mmdc@021b0000 {
- compatible = "fsl,imx6ul-mmdc", "fsl,imx6q-mmdc";
- reg = <0x021b0000 0x4000>;
- };
-
- lcdif: lcdif@021c8000 {
- compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
- reg = <0x021c8000 0x4000>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
- <&clks IMX6UL_CLK_LCDIF_APB>,
- <&clks IMX6UL_CLK_DUMMY>;
- clock-names = "pix", "axi", "disp_axi";
- status = "disabled";
- };
-
- qspi: qspi@021e0000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
- reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
- reg-names = "QuadSPI", "QuadSPI-memory";
- interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_QSPI>,
- <&clks IMX6UL_CLK_QSPI>;
- clock-names = "qspi_en", "qspi";
- status = "disabled";
- };
-
- uart2: serial@021e8000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x021e8000 0x4000>;
- interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART2_IPG>,
- <&clks IMX6UL_CLK_UART2_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart3: serial@021ec000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x021ec000 0x4000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART3_IPG>,
- <&clks IMX6UL_CLK_UART3_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart4: serial@021f0000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x021f0000 0x4000>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART4_IPG>,
- <&clks IMX6UL_CLK_UART4_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart5: serial@021f4000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x021f4000 0x4000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART5_IPG>,
- <&clks IMX6UL_CLK_UART5_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- i2c4: i2c@021f8000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx6ul-i2c", "fsl,imx21-i2c";
- reg = <0x021f8000 0x4000>;
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_I2C4>;
- status = "disabled";
- };
-
- uart6: serial@021fc000 {
- compatible = "fsl,imx6ul-uart",
- "fsl,imx6q-uart";
- reg = <0x021fc000 0x4000>;
- interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX6UL_CLK_UART6_IPG>,
- <&clks IMX6UL_CLK_UART6_SERIAL>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
- };
- };
-};
diff --git a/arch/arm/boot/dts/imx6ull-14x14-evk.dts b/arch/arm/boot/dts/imx6ull-14x14-evk.dts
new file mode 100644
index 0000000..64c38bc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-14x14-evk.dts
@@ -0,0 +1,17 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+
+#include "imx6ull.dtsi"
+#include "imx6u-14x14-evk.dtsi"
+
+/ {
+ model = "Freescale i.MX6 UlltraLite 14x14 EVK Board";
+ compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc.h b/arch/arm/boot/dts/imx6ull-pinfunc.h
new file mode 100644
index 0000000..fca0036
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-pinfunc.h
@@ -0,0 +1,57 @@
+/*
+ * Copyright (C) 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef __DTS_IMX6ULL_PINFUNC_H
+#define __DTS_IMX6ULL_PINFUNC_H
+
+#include "imx6ul-pinfunc.h"
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+#define MX6UL_PAD_ENET2_RX_DATA0__EPDC_SDDO08 0x00E4 0x0370 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_RX_DATA1__EPDC_SDDO09 0x00E8 0x0374 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_RX_EN__EPDC_SDDO10 0x00EC 0x0378 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_TX_DATA0__EPDC_SDDO11 0x00F0 0x037C 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_TX_DATA1__EPDC_SDDO12 0x00F4 0x0380 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_TX_EN__EPDC_SDDO13 0x00F8 0x0384 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_TX_CLK__EPDC_SDDO14 0x00FC 0x0388 0x0000 0x9 0x0
+#define MX6UL_PAD_ENET2_RX_ER__EPDC_SDDO15 0x0100 0x038C 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_CLK__EPDC_SDCLK 0x0104 0x0390 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_ENABLE__EPDC_SDLE 0x0108 0x0394 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_HSYNC__EPDC_SDOE 0x010C 0x0398 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_VSYNC__EPDC_SDCE0 0x0110 0x039C 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_RESET__EPDC_GDOE 0x0114 0x03A0 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA00__EPDC_SDDO00 0x0118 0x03A4 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA01__EPDC_SDDO01 0x011C 0x03A8 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA02__EPDC_SDDO02 0x0120 0x03AC 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA03__EPDC_SDDO03 0x0124 0x03B0 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA04__EPDC_SDDO04 0x0128 0x03B4 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA05__EPDC_SDDO05 0x012C 0x03B8 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA06__EPDC_SDDO06 0x0130 0x03BC 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA07__EPDC_SDDO07 0x0134 0x03C0 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA14__EPDC_SDSHR 0x0150 0x03DC 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA15__EPDC_GDRL 0x0154 0x03E0 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA16__EPDC_GDCLK 0x0158 0x03E4 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA17__EPDC_GDSP 0x015C 0x03E8 0x0000 0x9 0x0
+#define MX6UL_PAD_LCD_DATA21__EPDC_SDCE1 0x016C 0x03F8 0x0000 0x9 0x0
+
+#define MX6UL_PAD_CSI_MCLK__ESAI_TX3_RX2 0x01D4 0x0460 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_PIXCLK__ESAI_TX2_RX3 0x01D8 0x0464 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_VSYNC__ESAI_TX4_RX1 0x01DC 0x0468 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_HSYNC__ESAI_TX1 0x01E0 0x046C 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA00__ESAI_TX_HF_CLK 0x01E4 0x0470 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA01__ESAI_RX_HF_CLK 0x01E8 0x0474 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA02__ESAI_RX_FS 0x01EC 0x0478 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA03__ESAI_RX_CLK 0x01F0 0x047C 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA04__ESAI_TX_FS 0x01F4 0x0480 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA05__ESAI_TX_CLK 0x01F8 0x0484 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA06__ESAI_TX5_RX0 0x01FC 0x0488 0x0000 0x9 0x0
+#define MX6UL_PAD_CSI_DATA07__ESAI_T0 0x0200 0x048C 0x0000 0x9 0x0
+
+#endif /* __DTS_IMX6ULL_PINFUNC_H */
diff --git a/arch/arm/boot/dts/imx6ull.dtsi b/arch/arm/boot/dts/imx6ull.dtsi
new file mode 100644
index 0000000..afd9796
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull.dtsi
@@ -0,0 +1,10 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "imx6u.dtsi"
+#include "imx6ull-pinfunc.h"
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH 3/3] clk: imx: clk-imx6ul: add clk support for imx6ull
[not found] ` <1477969343-19887-1-git-send-email-peter.chen-3arQi8VN3Tc@public.gmane.org>
2016-11-01 3:02 ` [PATCH 1/3] ARM: imx6u: " Peter Chen
2016-11-01 3:02 ` [PATCH 2/3] ARM: imx: mach-imx6ul: " Peter Chen
@ 2016-11-01 3:02 ` Peter Chen
[not found] ` <1477969343-19887-4-git-send-email-peter.chen-3arQi8VN3Tc@public.gmane.org>
2 siblings, 1 reply; 13+ messages in thread
From: Peter Chen @ 2016-11-01 3:02 UTC (permalink / raw)
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A, sboyd-sgV2jX0FEOL9JmXXK+q4OQ,
mturquette-rdvid1DuHRBWk0Htik3J/w
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ, devicetree-u79uwXL29TY76Z2rM5mHXA,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A, fabio.estevam-3arQi8VN3Tc,
mark.rutland-5wv7dgnIgG8, linux-clk-u79uwXL29TY76Z2rM5mHXA,
Bai Ping, Peng Fan, Peter Chen
From: Bai Ping <ping.bai-3arQi8VN3Tc@public.gmane.org>
imx6ull is the derived SoC from imx6ul
Cc: Michael Turquette <mturquette-rdvid1DuHRBWk0Htik3J/w@public.gmane.org>
Cc: Stephen Boyd <sboyd-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Peng Fan <peng.fan-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Bai Ping <ping.bai-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Peter Chen <peter.chen-3arQi8VN3Tc@public.gmane.org>
---
drivers/clk/imx/clk-imx6ul.c | 74 +++++++++++++++++++++++++++-----
include/dt-bindings/clock/imx6ul-clock.h | 15 ++++++-
2 files changed, 77 insertions(+), 12 deletions(-)
diff --git a/drivers/clk/imx/clk-imx6ul.c b/drivers/clk/imx/clk-imx6ul.c
index d1d7787..ceb99a7 100644
--- a/drivers/clk/imx/clk-imx6ul.c
+++ b/drivers/clk/imx/clk-imx6ul.c
@@ -64,6 +64,11 @@ static const char *perclk_sels[] = { "ipg", "osc", };
static const char *lcdif_sels[] = { "lcdif_podf", "ipp_di0", "ipp_di1", "ldb_di0", "ldb_di1", };
static const char *csi_sels[] = { "osc", "pll2_pfd2_396m", "pll3_120m", "pll3_pfd1_540m", };
static const char *sim_sels[] = { "sim_podf", "ipp_di0", "ipp_di1", "ldb_di0", "ldb_di1", };
+/* epdc_pre_sels, epdc_sels, esai_sels only exists on i.MX6ULL */
+static const char *epdc_pre_sels[] = { "pll2_bus", "pll3_usb_otg", "pll5_video_div", "pll2_pfd0_352m", "pll2_pfd2_396m", "pll3_pfd2_508m", };
+static const char *esai_sels[] = { "pll4_audio_div", "pll3_pfd2_508m", "pll5_video_div", "pll3_usb_otg", };
+static const char *epdc_sels[] = { "epdc_podf", "ipp_di0", "ipp_di1", "ldb_di0", "ldb_di1", };
+
static struct clk *clks[IMX6UL_CLK_END];
static struct clk_onecell_data clk_data;
@@ -102,6 +107,17 @@ static u32 share_count_audio;
static u32 share_count_sai1;
static u32 share_count_sai2;
static u32 share_count_sai3;
+static u32 share_count_esai;
+
+static inline int clk_on_imx6ul(void)
+{
+ return of_machine_is_compatible("fsl,imx6ul");
+}
+
+static inline int clk_on_imx6ull(void)
+{
+ return of_machine_is_compatible("fsl,imx6ull");
+}
static void __init imx6ul_clocks_init(struct device_node *ccm_node)
{
@@ -238,12 +254,19 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_QSPI1_SEL] = imx_clk_mux("qspi1_sel", base + 0x1c, 7, 3, qspi1_sels, ARRAY_SIZE(qspi1_sels));
clks[IMX6UL_CLK_PERCLK_SEL] = imx_clk_mux("perclk_sel", base + 0x1c, 6, 1, perclk_sels, ARRAY_SIZE(perclk_sels));
clks[IMX6UL_CLK_CAN_SEL] = imx_clk_mux("can_sel", base + 0x20, 8, 2, can_sels, ARRAY_SIZE(can_sels));
+ if (clk_on_imx6ull())
+ clks[IMX6UL_CLK_ESAI_SEL] = imx_clk_mux("esai_sel", base + 0x20, 19, 2, esai_sels, ARRAY_SIZE(esai_sels));
clks[IMX6UL_CLK_UART_SEL] = imx_clk_mux("uart_sel", base + 0x24, 6, 1, uart_sels, ARRAY_SIZE(uart_sels));
clks[IMX6UL_CLK_ENFC_SEL] = imx_clk_mux("enfc_sel", base + 0x2c, 15, 3, enfc_sels, ARRAY_SIZE(enfc_sels));
clks[IMX6UL_CLK_LDB_DI0_SEL] = imx_clk_mux("ldb_di0_sel", base + 0x2c, 9, 3, ldb_di0_sels, ARRAY_SIZE(ldb_di0_sels));
clks[IMX6UL_CLK_SPDIF_SEL] = imx_clk_mux("spdif_sel", base + 0x30, 20, 2, spdif_sels, ARRAY_SIZE(spdif_sels));
- clks[IMX6UL_CLK_SIM_PRE_SEL] = imx_clk_mux("sim_pre_sel", base + 0x34, 15, 3, sim_pre_sels, ARRAY_SIZE(sim_pre_sels));
- clks[IMX6UL_CLK_SIM_SEL] = imx_clk_mux("sim_sel", base + 0x34, 9, 3, sim_sels, ARRAY_SIZE(sim_sels));
+ if (clk_on_imx6ul()) {
+ clks[IMX6UL_CLK_SIM_PRE_SEL] = imx_clk_mux("sim_pre_sel", base + 0x34, 15, 3, sim_pre_sels, ARRAY_SIZE(sim_pre_sels));
+ clks[IMX6UL_CLK_SIM_SEL] = imx_clk_mux("sim_sel", base + 0x34, 9, 3, sim_sels, ARRAY_SIZE(sim_sels));
+ } else if (clk_on_imx6ull()) {
+ clks[IMX6UL_CLK_EPDC_PRE_SEL] = imx_clk_mux("epdc_pre_sel", base + 0x34, 15, 3, epdc_pre_sels, ARRAY_SIZE(epdc_pre_sels));
+ clks[IMX6UL_CLK_EPDC_SEL] = imx_clk_mux("epdc_sel", base + 0x34, 9, 3, epdc_sels, ARRAY_SIZE(epdc_sels));
+ }
clks[IMX6UL_CLK_ECSPI_SEL] = imx_clk_mux("ecspi_sel", base + 0x38, 18, 1, ecspi_sels, ARRAY_SIZE(ecspi_sels));
clks[IMX6UL_CLK_LCDIF_PRE_SEL] = imx_clk_mux("lcdif_pre_sel", base + 0x38, 15, 3, lcdif_pre_sels, ARRAY_SIZE(lcdif_pre_sels));
clks[IMX6UL_CLK_LCDIF_SEL] = imx_clk_mux("lcdif_sel", base + 0x38, 9, 3, lcdif_sels, ARRAY_SIZE(lcdif_sels));
@@ -276,6 +299,10 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_SAI3_PODF] = imx_clk_divider("sai3_podf", "sai3_pred", base + 0x28, 16, 6);
clks[IMX6UL_CLK_SAI1_PRED] = imx_clk_divider("sai1_pred", "sai1_sel", base + 0x28, 6, 3);
clks[IMX6UL_CLK_SAI1_PODF] = imx_clk_divider("sai1_podf", "sai1_pred", base + 0x28, 0, 6);
+ if (clk_on_imx6ull()) {
+ clks[IMX6UL_CLK_ESAI_PRED] = imx_clk_divider("esai_pred", "esai_sel", base + 0x28, 9, 3);
+ clks[IMX6UL_CLK_ESAI_PODF] = imx_clk_divider("esai_podf", "esai_pred", base + 0x28, 25, 3);
+ }
clks[IMX6UL_CLK_ENFC_PRED] = imx_clk_divider("enfc_pred", "enfc_sel", base + 0x2c, 18, 3);
clks[IMX6UL_CLK_ENFC_PODF] = imx_clk_divider("enfc_podf", "enfc_pred", base + 0x2c, 21, 6);
clks[IMX6UL_CLK_SAI2_PRED] = imx_clk_divider("sai2_pred", "sai2_sel", base + 0x2c, 6, 3);
@@ -298,9 +325,15 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_APBHDMA] = imx_clk_gate2("apbh_dma", "bch_podf", base + 0x68, 4);
clks[IMX6UL_CLK_ASRC_IPG] = imx_clk_gate2_shared("asrc_ipg", "ahb", base + 0x68, 6, &share_count_asrc);
clks[IMX6UL_CLK_ASRC_MEM] = imx_clk_gate2_shared("asrc_mem", "ahb", base + 0x68, 6, &share_count_asrc);
- clks[IMX6UL_CLK_CAAM_MEM] = imx_clk_gate2("caam_mem", "ahb", base + 0x68, 8);
- clks[IMX6UL_CLK_CAAM_ACLK] = imx_clk_gate2("caam_aclk", "ahb", base + 0x68, 10);
- clks[IMX6UL_CLK_CAAM_IPG] = imx_clk_gate2("caam_ipg", "ipg", base + 0x68, 12);
+ if (clk_on_imx6ul()) {
+ clks[IMX6UL_CLK_CAAM_MEM] = imx_clk_gate2("caam_mem", "ahb", base + 0x68, 8);
+ clks[IMX6UL_CLK_CAAM_ACLK] = imx_clk_gate2("caam_aclk", "ahb", base + 0x68, 10);
+ clks[IMX6UL_CLK_CAAM_IPG] = imx_clk_gate2("caam_ipg", "ipg", base + 0x68, 12);
+ } else if (clk_on_imx6ull()) {
+ clks[IMX6UL_CLK_DCP_CLK] = imx_clk_gate2("dcp", "ahb", base + 0x68, 10);
+ clks[IMX6UL_CLK_ENET] = imx_clk_gate2("enet", "ipg", base + 0x68, 12);
+ clks[IMX6UL_CLK_ENET_AHB] = imx_clk_gate2("enet_ahb", "ahb", base + 0x68, 12);
+ }
clks[IMX6UL_CLK_CAN1_IPG] = imx_clk_gate2("can1_ipg", "ipg", base + 0x68, 14);
clks[IMX6UL_CLK_CAN1_SERIAL] = imx_clk_gate2("can1_serial", "can_podf", base + 0x68, 16);
clks[IMX6UL_CLK_CAN2_IPG] = imx_clk_gate2("can2_ipg", "ipg", base + 0x68, 18);
@@ -309,7 +342,10 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_GPT2_SERIAL] = imx_clk_gate2("gpt2_serial", "perclk", base + 0x68, 26);
clks[IMX6UL_CLK_UART2_IPG] = imx_clk_gate2("uart2_ipg", "ipg", base + 0x68, 28);
clks[IMX6UL_CLK_UART2_SERIAL] = imx_clk_gate2("uart2_serial", "uart_podf", base + 0x68, 28);
- clks[IMX6UL_CLK_AIPSTZ3] = imx_clk_gate2("aips_tz3", "ahb", base + 0x68, 30);
+ if (clk_on_imx6ul())
+ clks[IMX6UL_CLK_AIPSTZ3] = imx_clk_gate2("aips_tz3", "ahb", base + 0x68, 30);
+ else if (clk_on_imx6ull())
+ clks[IMX6UL_CLK_AIPSTZ3] = imx_clk_gate2("aips_tz3", "ahb", base + 0x80, 18);
/* CCGR1 */
clks[IMX6UL_CLK_ECSPI1] = imx_clk_gate2("ecspi1", "ecspi_podf", base + 0x6c, 0);
@@ -328,6 +364,11 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_UART4_SERIAL] = imx_clk_gate2("uart4_serail", "uart_podf", base + 0x6c, 24);
/* CCGR2 */
+ if (clk_on_imx6ull()) {
+ clks[IMX6UL_CLK_ESAI_EXTAL] = imx_clk_gate2_shared("esai_extal", "esai_podf", base + 0x70, 0, &share_count_esai);
+ clks[IMX6UL_CLK_ESAI_IPG] = imx_clk_gate2_shared("esai_ipg", "ahb", base + 0x70, 0, &share_count_esai);
+ clks[IMX6UL_CLK_ESAI_MEM] = imx_clk_gate2_shared("esai_mem", "ahb", base + 0x70, 0, &share_count_esai);
+ }
clks[IMX6UL_CLK_CSI] = imx_clk_gate2("csi", "csi_podf", base + 0x70, 2);
clks[IMX6UL_CLK_I2C1] = imx_clk_gate2("i2c1", "perclk", base + 0x70, 6);
clks[IMX6UL_CLK_I2C2] = imx_clk_gate2("i2c2", "perclk", base + 0x70, 8);
@@ -340,8 +381,13 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
/* CCGR3 */
clks[IMX6UL_CLK_UART5_IPG] = imx_clk_gate2("uart5_ipg", "ipg", base + 0x74, 2);
clks[IMX6UL_CLK_UART5_SERIAL] = imx_clk_gate2("uart5_serial", "uart_podf", base + 0x74, 2);
- clks[IMX6UL_CLK_ENET] = imx_clk_gate2("enet", "ipg", base + 0x74, 4);
- clks[IMX6UL_CLK_ENET_AHB] = imx_clk_gate2("enet_ahb", "ahb", base + 0x74, 4);
+ if (clk_on_imx6ul()) {
+ clks[IMX6UL_CLK_ENET] = imx_clk_gate2("enet", "ipg", base + 0x74, 4);
+ clks[IMX6UL_CLK_ENET_AHB] = imx_clk_gate2("enet_ahb", "ahb", base + 0x74, 4);
+ } else if (clk_on_imx6ull()) {
+ clks[IMX6UL_CLK_EPDC_ACLK] = imx_clk_gate2("epdc_aclk", "axi", base + 0x74, 4);
+ clks[IMX6UL_CLK_EPDC_PIX] = imx_clk_gate2("epdc_pix", "epdc_podf", base + 0x74, 4);
+ }
clks[IMX6UL_CLK_UART6_IPG] = imx_clk_gate2("uart6_ipg", "ipg", base + 0x74, 6);
clks[IMX6UL_CLK_UART6_SERIAL] = imx_clk_gate2("uart6_serial", "uart_podf", base + 0x74, 6);
clks[IMX6UL_CLK_LCDIF_PIX] = imx_clk_gate2("lcdif_pix", "lcdif_podf", base + 0x74, 10);
@@ -385,8 +431,10 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clks[IMX6UL_CLK_USBOH3] = imx_clk_gate2("usboh3", "ipg", base + 0x80, 0);
clks[IMX6UL_CLK_USDHC1] = imx_clk_gate2("usdhc1", "usdhc1_podf", base + 0x80, 2);
clks[IMX6UL_CLK_USDHC2] = imx_clk_gate2("usdhc2", "usdhc2_podf", base + 0x80, 4);
- clks[IMX6UL_CLK_SIM1] = imx_clk_gate2("sim1", "sim_sel", base + 0x80, 6);
- clks[IMX6UL_CLK_SIM2] = imx_clk_gate2("sim2", "sim_sel", base + 0x80, 8);
+ if (clk_on_imx6ul()) {
+ clks[IMX6UL_CLK_SIM1] = imx_clk_gate2("sim1", "sim_sel", base + 0x80, 6);
+ clks[IMX6UL_CLK_SIM2] = imx_clk_gate2("sim2", "sim_sel", base + 0x80, 8);
+ }
clks[IMX6UL_CLK_EIM] = imx_clk_gate2("eim", "eim_slow_podf", base + 0x80, 10);
clks[IMX6UL_CLK_PWM8] = imx_clk_gate2("pwm8", "perclk", base + 0x80, 16);
clks[IMX6UL_CLK_UART8_IPG] = imx_clk_gate2("uart8_ipg", "ipg", base + 0x80, 14);
@@ -430,6 +478,7 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
clk_set_rate(clks[IMX6UL_CLK_ENET_REF], 50000000);
clk_set_rate(clks[IMX6UL_CLK_ENET2_REF], 50000000);
clk_set_rate(clks[IMX6UL_CLK_CSI], 24000000);
+ clk_set_rate(clks[IMX6UL_CLK_PLL3_PFD2], 320000000);
/* keep all the clks on just for bringup */
for (i = 0; i < ARRAY_SIZE(clks_init_on); i++)
@@ -441,7 +490,10 @@ static void __init imx6ul_clocks_init(struct device_node *ccm_node)
}
clk_set_parent(clks[IMX6UL_CLK_CAN_SEL], clks[IMX6UL_CLK_PLL3_60M]);
- clk_set_parent(clks[IMX6UL_CLK_SIM_PRE_SEL], clks[IMX6UL_CLK_PLL3_USB_OTG]);
+ if (clk_on_imx6ul())
+ clk_set_parent(clks[IMX6UL_CLK_SIM_PRE_SEL], clks[IMX6UL_CLK_PLL3_USB_OTG]);
+ else if (clk_on_imx6ull())
+ clk_set_parent(clks[IMX6UL_CLK_EPDC_PRE_SEL], clks[IMX6UL_CLK_PLL3_PFD2]);
clk_set_parent(clks[IMX6UL_CLK_ENFC_SEL], clks[IMX6UL_CLK_PLL2_PFD2]);
}
diff --git a/include/dt-bindings/clock/imx6ul-clock.h b/include/dt-bindings/clock/imx6ul-clock.h
index fd8aee8..563fd5b 100644
--- a/include/dt-bindings/clock/imx6ul-clock.h
+++ b/include/dt-bindings/clock/imx6ul-clock.h
@@ -236,6 +236,19 @@
#define IMX6UL_CLK_PLL3_120M 223
#define IMX6UL_CLK_KPP 224
-#define IMX6UL_CLK_END 225
+/* For i.MX6ULL */
+#define IMX6UL_CLK_ESAI_PRED 225
+#define IMX6UL_CLK_ESAI_PODF 226
+#define IMX6UL_CLK_ESAI_EXTAL 227
+#define IMX6UL_CLK_ESAI_MEM 228
+#define IMX6UL_CLK_ESAI_IPG 229
+#define IMX6UL_CLK_DCP_CLK 230
+#define IMX6UL_CLK_EPDC_PRE_SEL 231
+#define IMX6UL_CLK_EPDC_SEL 232
+#define IMX6UL_CLK_EPDC_PODF 233
+#define IMX6UL_CLK_EPDC_ACLK 234
+#define IMX6UL_CLK_EPDC_PIX 235
+#define IMX6UL_CLK_ESAI_SEL 236
+#define IMX6UL_CLK_END 237
#endif /* __DT_BINDINGS_CLOCK_IMX6UL_H */
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 13+ messages in thread