devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Ritesh Harjani <riteshh@codeaurora.org>
To: ulf.hansson@linaro.org, linux-mmc@vger.kernel.org,
	adrian.hunter@intel.com, sboyd@codeaurora.org,
	andy.gross@linaro.org
Cc: shawn.lin@rock-chips.com, devicetree@vger.kernel.org,
	linux-clk@vger.kernel.org, david.brown@linaro.org,
	linux-arm-msm@vger.kernel.org, georgi.djakov@linaro.org,
	alex.lemberg@sandisk.com, mateusz.nowak@intel.com,
	Yuliy.Izrailov@sandisk.com, asutoshd@codeaurora.org,
	david.griego@linaro.org, stummala@codeaurora.org,
	venkatg@codeaurora.org, rnayak@codeaurora.org,
	pramod.gurav@linaro.org, jeremymc@redhat.com,
	Ritesh Harjani <riteshh@codeaurora.org>
Subject: [PATCH v8 03/16] mmc: sdhci-msm: Change poor style writel/readl of registers
Date: Wed, 16 Nov 2016 21:30:39 +0530	[thread overview]
Message-ID: <1479312052-22396-4-git-send-email-riteshh@codeaurora.org> (raw)
In-Reply-To: <1479312052-22396-1-git-send-email-riteshh@codeaurora.org>

This patch changes the poor style of writel/readl registers
into more readable format. This avoid mixed style format
of readl/writel in sdhci-msm driver.
This patch also removes the one line comments which were present for
above writel/readl, since they were of no help.

Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
---
 drivers/mmc/host/sdhci-msm.c | 62 +++++++++++++++++++++++---------------------
 1 file changed, 32 insertions(+), 30 deletions(-)

diff --git a/drivers/mmc/host/sdhci-msm.c b/drivers/mmc/host/sdhci-msm.c
index b78d72f..2dcbeb0 100644
--- a/drivers/mmc/host/sdhci-msm.c
+++ b/drivers/mmc/host/sdhci-msm.c
@@ -138,9 +138,9 @@ static int msm_config_cm_dll_phase(struct sdhci_host *host, u8 phase)
 	config |= grey_coded_phase_table[phase] << CDR_SELEXT_SHIFT;
 	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
-	/* Set CK_OUT_EN bit of DLL_CONFIG register to 1. */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			| CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config |= CORE_CK_OUT_EN;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
 	/* Wait until CK_OUT_EN bit of DLL_CONFIG register becomes '1' */
 	rc = msm_dll_poll_ck_out_en(host, 1);
@@ -307,6 +307,7 @@ static int msm_init_cm_dll(struct sdhci_host *host)
 	struct mmc_host *mmc = host->mmc;
 	int wait_cnt = 50;
 	unsigned long flags;
+	u32 config;
 
 	spin_lock_irqsave(&host->lock, flags);
 
@@ -315,33 +316,34 @@ static int msm_init_cm_dll(struct sdhci_host *host)
 	 * tuning is in progress. Keeping PWRSAVE ON may
 	 * turn off the clock.
 	 */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC)
-			& ~CORE_CLK_PWRSAVE), host->ioaddr + CORE_VENDOR_SPEC);
+	config = readl_relaxed(host->ioaddr + CORE_VENDOR_SPEC);
+	config &= ~CORE_CLK_PWRSAVE;
+	writel_relaxed(config, host->ioaddr + CORE_VENDOR_SPEC);
 
-	/* Write 1 to DLL_RST bit of DLL_CONFIG register */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			| CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config |= CORE_DLL_RST;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
-	/* Write 1 to DLL_PDN bit of DLL_CONFIG register */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			| CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config |= CORE_DLL_PDN;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 	msm_cm_dll_set_freq(host);
 
-	/* Write 0 to DLL_RST bit of DLL_CONFIG register */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			& ~CORE_DLL_RST), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config &= ~CORE_DLL_RST;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
-	/* Write 0 to DLL_PDN bit of DLL_CONFIG register */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			& ~CORE_DLL_PDN), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config &= ~CORE_DLL_PDN;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
-	/* Set DLL_EN bit to 1. */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			| CORE_DLL_EN), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config |= CORE_DLL_EN;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
-	/* Set CK_OUT_EN bit to 1. */
-	writel_relaxed((readl_relaxed(host->ioaddr + CORE_DLL_CONFIG)
-			| CORE_CK_OUT_EN), host->ioaddr + CORE_DLL_CONFIG);
+	config = readl_relaxed(host->ioaddr + CORE_DLL_CONFIG);
+	config |= CORE_CK_OUT_EN;
+	writel_relaxed(config, host->ioaddr + CORE_DLL_CONFIG);
 
 	/* Wait until DLL_LOCK bit of DLL_STATUS register becomes '1' */
 	while (!(readl_relaxed(host->ioaddr + CORE_DLL_STATUS) &
@@ -538,7 +540,7 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 	struct resource *core_memres;
 	int ret;
 	u16 host_version, core_minor;
-	u32 core_version, caps;
+	u32 core_version, config;
 	u8 core_major;
 
 	host = sdhci_pltfm_init(pdev, &sdhci_msm_pdata, sizeof(*msm_host));
@@ -606,9 +608,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 		goto clk_disable;
 	}
 
-	/* Reset the core and Enable SDHC mode */
-	writel_relaxed(readl_relaxed(msm_host->core_mem + CORE_POWER) |
-		       CORE_SW_RST, msm_host->core_mem + CORE_POWER);
+	config = readl_relaxed(msm_host->core_mem + CORE_POWER);
+	config |= CORE_SW_RST;
+	writel_relaxed(config, msm_host->core_mem + CORE_POWER);
 
 	/* SW reset can take upto 10HCLK + 15MCLK cycles. (min 40us) */
 	usleep_range(1000, 5000);
@@ -638,9 +640,9 @@ static int sdhci_msm_probe(struct platform_device *pdev)
 	 * controller versions and must be explicitly enabled.
 	 */
 	if (core_major >= 1 && core_minor != 0x11 && core_minor != 0x12) {
-		caps = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
-		caps |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
-		writel_relaxed(caps, host->ioaddr +
+		config = readl_relaxed(host->ioaddr + SDHCI_CAPABILITIES);
+		config |= SDHCI_CAN_VDD_300 | SDHCI_CAN_DO_8BIT;
+		writel_relaxed(config, host->ioaddr +
 			       CORE_VENDOR_SPEC_CAPABILITIES0);
 	}
 
-- 
The Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, 
a Linux Foundation Collaborative Project.

  parent reply	other threads:[~2016-11-16 16:00 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2016-11-16 16:00 [PATCH v8 00/16] mmc: sdhci-msm: Add clk-rates, DDR, HS400 support Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 01/16] clk: qcom: Add rcg ops to return floor value closest to the requested rate Ritesh Harjani
2016-11-16 16:00 ` Ritesh Harjani [this message]
2016-11-16 16:00 ` [PATCH v8 04/16] ARM: dts: Add xo_clock to sdhc nodes on qcom platforms Ritesh Harjani
2016-11-17  0:43   ` [PATCH v8 04/16] ARM: dts: Add xo to sdhc clock node " Ritesh Harjani
2016-11-18  3:56     ` Andy Gross
2016-11-21  6:30       ` Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 05/16] dt-bindings: sdhci-msm: Add xo_clock property Ritesh Harjani
2016-11-16 19:13   ` Stephen Boyd
2016-11-17  0:41     ` Ritesh Harjani
2016-11-17  0:47     ` [PATCH v8 05/16] dt-bindings: sdhci-msm: Add xo property Ritesh Harjani
2016-11-17 23:03       ` Stephen Boyd
     [not found]         ` <20161117230352.GO25626-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-21  6:31           ` Ritesh Harjani
     [not found]       ` <1479343623-31163-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-18 14:17         ` Rob Herring
2016-11-16 16:00 ` [PATCH v8 07/16] mmc: sdhci-msm: Add get_min_clock() and get_max_clock() callback Ritesh Harjani
     [not found] ` <1479312052-22396-1-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-16 16:00   ` [PATCH v8 02/16] clk: qcom: Move all sdcc rcgs to use clk_rcg2_floor_ops Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 06/16] mmc: sdhci-msm: Update DLL reset sequence Ritesh Harjani
     [not found]     ` <1479312052-22396-7-git-send-email-riteshh-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2016-11-17  0:50       ` Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 08/16] mmc: sdhci-msm: Enable few quirks Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 09/16] mmc: sdhci: Factor out sdhci_enable_clock Ritesh Harjani
2016-11-18 13:56     ` Adrian Hunter
2016-11-21  6:31       ` Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 10/16] mmc: sdhci-msm: Implement set_clock callback for sdhci-msm Ritesh Harjani
2016-11-18 14:14     ` Adrian Hunter
2016-11-16 16:00   ` [PATCH v8 12/16] arm64: dts: qcom: msm8916: Add ddr support to sdhc1 Ritesh Harjani
2016-11-17  0:52     ` Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 13/16] mmc: sdhci-msm: Add HS400 platform support Ritesh Harjani
2016-11-16 16:00   ` [PATCH v8 16/16] sdhci: sdhci-msm: update dll configuration Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 11/16] mmc: sdhci-msm: Add clock changes for DDR mode Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 14/16] mmc: sdhci-msm: Save the calculated tuning phase Ritesh Harjani
2016-11-16 16:00 ` [PATCH v8 15/16] mmc: sdhci-msm: Add calibration tuning for CDCLP533 circuit Ritesh Harjani
2016-11-17  0:08 ` [PATCH v8 00/16] mmc: sdhci-msm: Add clk-rates, DDR, HS400 support Jeremy McNicoll

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1479312052-22396-4-git-send-email-riteshh@codeaurora.org \
    --to=riteshh@codeaurora.org \
    --cc=Yuliy.Izrailov@sandisk.com \
    --cc=adrian.hunter@intel.com \
    --cc=alex.lemberg@sandisk.com \
    --cc=andy.gross@linaro.org \
    --cc=asutoshd@codeaurora.org \
    --cc=david.brown@linaro.org \
    --cc=david.griego@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=georgi.djakov@linaro.org \
    --cc=jeremymc@redhat.com \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-mmc@vger.kernel.org \
    --cc=mateusz.nowak@intel.com \
    --cc=pramod.gurav@linaro.org \
    --cc=rnayak@codeaurora.org \
    --cc=sboyd@codeaurora.org \
    --cc=shawn.lin@rock-chips.com \
    --cc=stummala@codeaurora.org \
    --cc=ulf.hansson@linaro.org \
    --cc=venkatg@codeaurora.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).