* [PATCH 1/7] ARM: dts: NSP: DT Clean-ups
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
@ 2016-12-13 18:13 ` Jon Mason
2016-12-13 18:13 ` [PATCH 2/7] ARM: dts: NSP: Correct NAND partition unit address Jon Mason
` (12 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
The QSPI entry was added out of the sequental order that the rest of the
DTSI file is in. Move it to make it fit in properly. Also, some other
entries have been added in a non-alphabetical order in the DTS files,
making them different from the other NSP DTS files. Move the relevant
peices to make it match. Finally, remove errant new lines.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm-nsp.dtsi | 46 +++++++++++++--------------
arch/arm/boot/dts/bcm958522er.dts | 1 -
arch/arm/boot/dts/bcm958525er.dts | 1 -
arch/arm/boot/dts/bcm958525xmc.dts | 26 ++++++++--------
arch/arm/boot/dts/bcm958623hr.dts | 16 +++++-----
arch/arm/boot/dts/bcm958625hr.dts | 30 +++++++++---------
arch/arm/boot/dts/bcm958625k.dts | 64 +++++++++++++++++++-------------------
7 files changed, 91 insertions(+), 93 deletions(-)
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index b6142bd..9cd77ab 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -241,29 +241,6 @@
brcm,nand-has-wp;
};
- gpiob: gpio@30000 {
- compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
- reg = <0x30000 0x50>;
- #gpio-cells = <2>;
- gpio-controller;
- ngpios = <4>;
- interrupt-controller;
- interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pwm: pwm@31000 {
- compatible = "brcm,iproc-pwm";
- reg = <0x31000 0x28>;
- clocks = <&osc>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- rng: rng@33000 {
- compatible = "brcm,bcm-nsp-rng";
- reg = <0x33000 0x14>;
- };
-
qspi: qspi@27200 {
compatible = "brcm,spi-bcm-qspi", "brcm,spi-nsp-qspi";
reg = <0x027200 0x184>,
@@ -293,6 +270,29 @@
#size-cells = <0>;
};
+ gpiob: gpio@30000 {
+ compatible = "brcm,iproc-nsp-gpio", "brcm,iproc-gpio";
+ reg = <0x30000 0x50>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ ngpios = <4>;
+ interrupt-controller;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pwm: pwm@31000 {
+ compatible = "brcm,iproc-pwm";
+ reg = <0x31000 0x28>;
+ clocks = <&osc>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ rng: rng@33000 {
+ compatible = "brcm,bcm-nsp-rng";
+ reg = <0x33000 0x14>;
+ };
+
ccbtimer0: timer@34000 {
compatible = "arm,sp804";
reg = <0x34000 0x1000>;
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/bcm958522er.dts
index a21b0fd..7afd845 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -65,7 +65,6 @@
status = "okay";
};
-
&amac1 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/bcm958525er.dts
index be7f2f8..9da18cd 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -65,7 +65,6 @@
status = "okay";
};
-
&amac1 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index 959cde9..4492f55 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -59,6 +59,8 @@
};
};
+/* XHCI, MMC, and Ethernet support needed to be complete */
+
&i2c0 {
temperature-sensor@4c {
compatible = "adi,adt7461a";
@@ -115,12 +117,6 @@
};
};
-/* XHCI, MMC, and Ethernet support needed to be complete */
-
-&uart0 {
- status = "okay";
-};
-
&pcie0 {
status = "okay";
};
@@ -129,6 +125,15 @@
status = "okay";
};
+&pinctrl {
+ pinctrl-names = "default";
+ pinctrl-0 = <&nand_sel>;
+ nand_sel: nand_sel {
+ function = "nand";
+ groups = "nand_grp";
+ };
+};
+
&sata_phy0 {
status = "okay";
};
@@ -141,11 +146,6 @@
status = "okay";
};
-&pinctrl {
- pinctrl-names = "default";
- pinctrl-0 = <&nand_sel>;
- nand_sel: nand_sel {
- function = "nand";
- groups = "nand_grp";
- };
+&uart0 {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index 4ceb8fe..32ea59a 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -120,6 +120,14 @@
};
};
+&sata_phy0 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
&srab {
compatible = "brcm,bcm58623-srab", "brcm,nsp-srab";
status = "okay";
@@ -165,14 +173,6 @@
};
};
-&sata_phy0 {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index 4420025..e7a4cb1 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -1,7 +1,7 @@
/*
* BSD LICENSE
*
- * Copyright (c) 2016 Broadcom. All rights reserved.
+ * Copyright(c) 2016 Broadcom. All rights reserved.
*
* Redistribution and use in source and binary forms, with or without
* modification, are permitted provided that the following conditions
@@ -59,6 +59,10 @@
};
};
+&amac0 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
@@ -97,10 +101,6 @@
};
};
-&uart0 {
- status = "okay";
-};
-
&pcie0 {
status = "okay";
};
@@ -118,7 +118,15 @@
};
};
-&amac0 {
+&sata_phy0 {
+ status = "okay";
+};
+
+&sata_phy1 {
+ status = "okay";
+};
+
+&sata {
status = "okay";
};
@@ -167,14 +175,6 @@
};
};
-&sata_phy0 {
- status = "okay";
-};
-
-&sata_phy1 {
- status = "okay";
-};
-
-&sata {
+&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 59d96fb..98337d6 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -53,14 +53,6 @@
};
};
-&uart0 {
- status = "okay";
-};
-
-&uart1 {
- status = "okay";
-};
-
&amac0 {
status = "okay";
};
@@ -69,30 +61,6 @@
status = "okay";
};
-&pcie0 {
- status = "okay";
-};
-
-&pcie1 {
- status = "okay";
-};
-
-&pcie2 {
- status = "okay";
-};
-
-&sata_phy0 {
- status = "okay";
-};
-
-&sata_phy1 {
- status = "okay";
-};
-
-&sata {
- status = "okay";
-};
-
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
@@ -131,6 +99,18 @@
};
};
+&pcie0 {
+ status = "okay";
+};
+
+&pcie1 {
+ status = "okay";
+};
+
+&pcie2 {
+ status = "okay";
+};
+
&pinctrl {
pinctrl-names = "default";
pinctrl-0 = <&nand_sel>;
@@ -173,3 +153,23 @@
};
};
};
+
+&sata_phy0 {
+ status = "okay";
+};
+
+&sata_phy1 {
+ status = "okay";
+};
+
+&sata {
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH 2/7] ARM: dts: NSP: Correct NAND partition unit address
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
2016-12-13 18:13 ` [PATCH 1/7] ARM: dts: NSP: DT Clean-ups Jon Mason
@ 2016-12-13 18:13 ` Jon Mason
2016-12-13 18:13 ` [PATCH 3/7] ARM: dts: NSP: Add QSPI support to missing boards Jon Mason
` (11 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
The NAND partition unit address does not match the other NSP device tree
files. This change makes them uniform.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm958625k.dts | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 98337d6..dc24056 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -80,19 +80,19 @@
reg = <0x00000000 0x00200000>;
read-only;
};
- partition@1 {
+ partition@200000 {
label = "nenv";
reg = <0x00200000 0x00400000>;
};
- partition@2 {
+ partition@600000 {
label = "nsystem";
reg = <0x00600000 0x00a00000>;
};
- partition@3 {
+ partition@1000000 {
label = "nrootfs";
reg = <0x01000000 0x03000000>;
};
- partition@4 {
+ partition@4000000 {
label = "ncustfs";
reg = <0x04000000 0x3c000000>;
};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH 3/7] ARM: dts: NSP: Add QSPI support to missing boards
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
2016-12-13 18:13 ` [PATCH 1/7] ARM: dts: NSP: DT Clean-ups Jon Mason
2016-12-13 18:13 ` [PATCH 2/7] ARM: dts: NSP: Correct NAND partition unit address Jon Mason
@ 2016-12-13 18:13 ` Jon Mason
[not found] ` <1481652831-2744-1-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
` (10 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
QSPI device tree entries are present in bcm958625k, but missing from
bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
all of those that are missing it (as they are identical).
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm958522er.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958525er.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958525xmc.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958622hr.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958623hr.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm958625hr.dts | 34 ++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/bcm988312hr.dts | 34 ++++++++++++++++++++++++++++++++++
7 files changed, 238 insertions(+)
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/bcm958522er.dts
index 7afd845..3f04a40 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -124,6 +124,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/bcm958525er.dts
index 9da18cd..9fd5422 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -124,6 +124,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&sata_phy0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index 4492f55..89d9abc 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -134,6 +134,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&sata_phy0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/bcm958622hr.dts
index ad2aa87..18b8ffb 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -120,6 +120,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&srab {
compatible = "brcm,bcm58622-srab", "brcm,nsp-srab";
status = "okay";
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index 32ea59a..61499ae 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -128,6 +128,40 @@
status = "okay";
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&srab {
compatible = "brcm,bcm58623-srab", "brcm,nsp-srab";
status = "okay";
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index e7a4cb1..94cce23 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -118,6 +118,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&sata_phy0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/bcm988312hr.dts
index 104afe9..c324c9f 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -120,6 +120,40 @@
};
};
+&qspi {
+ bspi-sel = <0>;
+ flash: m25p80@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p80";
+ reg = <0x0>;
+ spi-max-frequency = <12500000>;
+ m25p,fast-read;
+ spi-cpol;
+ spi-cpha;
+
+ partition@0 {
+ label = "boot";
+ reg = <0x00000000 0x000a0000>;
+ };
+
+ partition@a0000 {
+ label = "env";
+ reg = <0x000a0000 0x00060000>;
+ };
+
+ partition@100000 {
+ label = "system";
+ reg = <0x00100000 0x00600000>;
+ };
+
+ partition@700000 {
+ label = "rootfs";
+ reg = <0x00700000 0x01900000>;
+ };
+ };
+};
+
&sata_phy0 {
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread[parent not found: <1481652831-2744-1-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
* [PATCH 4/7] ARM: dts: NSP: Add BCM958625K switch ports
[not found] ` <1481652831-2744-1-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
@ 2016-12-13 18:13 ` Jon Mason
0 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
Add the layout of the switch ports found on the BCM958625K reference
board. The CPU port is hooked up to the AMAC0 Ethernet controller
adapter.
Signed-off-by: Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
---
arch/arm/boot/dts/bcm958625k.dts | 45 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index dc24056..7aa86c7 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -120,6 +120,51 @@
};
};
+&srab {
+ compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ label = "port0";
+ reg = <0>;
+ };
+
+ port@1 {
+ label = "port1";
+ reg = <1>;
+ };
+
+ port@2 {
+ label = "port2";
+ reg = <2>;
+ };
+
+ port@3 {
+ label = "port3";
+ reg = <3>;
+ };
+
+ port@4 {
+ label = "port4";
+ reg = <4>;
+ };
+
+ port@5 {
+ ethernet = <&amac0>;
+ label = "cpu";
+ reg = <5>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
&qspi {
bspi-sel = <0>;
flash: m25p80@0 {
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 15+ messages in thread
* [PATCH 5/7] ARM: dts: NSP: Add and enable amac2
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
` (3 preceding siblings ...)
[not found] ` <1481652831-2744-1-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
@ 2016-12-13 18:13 ` Jon Mason
2016-12-13 18:13 ` [PATCH 6/7] ARM: dts: NSP: Add Ethernet to NSP XMC Jon Mason
` (8 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
Add and enable the third AMAC ethernet interface in the device trees for
the platforms where it is present. Also, enable amac1 on some of the
platforms where that was missing.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm-nsp.dtsi | 9 +++++++++
arch/arm/boot/dts/bcm958622hr.dts | 8 ++++++++
arch/arm/boot/dts/bcm958623hr.dts | 8 ++++++++
arch/arm/boot/dts/bcm958625hr.dts | 8 ++++++++
arch/arm/boot/dts/bcm958625k.dts | 4 ++++
arch/arm/boot/dts/bcm988312hr.dts | 8 ++++++++
6 files changed, 45 insertions(+)
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index 9cd77ab..ecffc16 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -227,6 +227,15 @@
status = "disabled";
};
+ amac2: ethernet@24000 {
+ compatible = "brcm,nsp-amac";
+ reg = <0x024000 0x1000>,
+ <0x112000 0x1000>;
+ reg-names = "amac_base", "idm_base";
+ interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
nand: nand@26000 {
compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
reg = <0x026000 0x600>,
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/bcm958622hr.dts
index 18b8ffb..477c486 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -65,6 +65,14 @@
status = "okay";
};
+&amac1 {
+ status = "okay";
+};
+
+&amac2 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index 61499ae..c0a499d 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -65,6 +65,14 @@
status = "okay";
};
+&amac1 {
+ status = "okay";
+};
+
+&amac2 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index 94cce23..f7eb585 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -63,6 +63,14 @@
status = "okay";
};
+&amac1 {
+ status = "okay";
+};
+
+&amac2 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 7aa86c7..6e994f2 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -61,6 +61,10 @@
status = "okay";
};
+&amac2 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/bcm988312hr.dts
index c324c9f..16666324 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -65,6 +65,14 @@
status = "okay";
};
+&amac1 {
+ status = "okay";
+};
+
+&amac2 {
+ status = "okay";
+};
+
&nand {
nandcs@0 {
compatible = "brcm,nandcs";
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH 6/7] ARM: dts: NSP: Add Ethernet to NSP XMC
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
` (4 preceding siblings ...)
2016-12-13 18:13 ` [PATCH 5/7] ARM: dts: NSP: Add and enable amac2 Jon Mason
@ 2016-12-13 18:13 ` Jon Mason
2016-12-13 18:13 ` [PATCH 7/7] ARM: dts: NSP: Add SD/MMC support Jon Mason
` (7 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
Enable the ethernet in the NSP XMC (bcm958525xmc) device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm958525xmc.dts | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index 89d9abc..3912269 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -59,7 +59,11 @@
};
};
-/* XHCI, MMC, and Ethernet support needed to be complete */
+/* XHCI and SD/MMC support needed to be complete */
+
+&amac0 {
+ status = "okay";
+};
&i2c0 {
temperature-sensor@4c {
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread* [PATCH 7/7] ARM: dts: NSP: Add SD/MMC support
2016-12-13 18:13 [PATCH 0/7] ARM: dts: NSP: DT Clean-ups and more Jon Mason
` (5 preceding siblings ...)
2016-12-13 18:13 ` [PATCH 6/7] ARM: dts: NSP: Add Ethernet to NSP XMC Jon Mason
@ 2016-12-13 18:13 ` Jon Mason
[not found] ` <1481652831-2744-2-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
` (6 subsequent siblings)
13 siblings, 0 replies; 15+ messages in thread
From: Jon Mason @ 2016-12-13 18:13 UTC (permalink / raw)
To: Rob Herring, Mark Rutland, Florian Fainelli
Cc: devicetree, bcm-kernel-feedback-list, linux-arm-kernel,
linux-kernel
Add SD/MMC support to the Broadcom NSP SVK and XMC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm/boot/dts/bcm-nsp.dtsi | 9 +++
arch/arm/boot/dts/bcm958525xmc.dts | 6 +-
arch/arm/boot/dts/bcm958625k.dts | 118 ++++++++++++++++++++++++-------------
3 files changed, 90 insertions(+), 43 deletions(-)
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index ecffc16..6c58c78 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -209,6 +209,15 @@
#dma-cells = <1>;
};
+ sdio: sdhci@21000 {
+ compatible = "brcm,sdhci-iproc-cygnus";
+ reg = <0x21000 0x100>;
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+ sdhci,auto-cmd12;
+ clocks = <&lcpll0 BCM_NSP_LCPLL0_SDIO_CLK>;
+ status = "disabled";
+ };
+
amac0: ethernet@22000 {
compatible = "brcm,nsp-amac";
reg = <0x022000 0x1000>,
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index 3912269..41e7fd3 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -59,7 +59,7 @@
};
};
-/* XHCI and SD/MMC support needed to be complete */
+/* XHCI support needed to be complete */
&amac0 {
status = "okay";
@@ -184,6 +184,10 @@
status = "okay";
};
+&sdio {
+ status = "ok";
+};
+
&uart0 {
status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 6e994f2..f8d47e5 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -117,58 +117,34 @@
&pinctrl {
pinctrl-names = "default";
- pinctrl-0 = <&nand_sel>;
+ pinctrl-0 = <&nand_sel>, <&gpiobs>, <&pwmc>;
+
nand_sel: nand_sel {
function = "nand";
groups = "nand_grp";
};
-};
-
-&srab {
- compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
- status = "okay";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- label = "port0";
- reg = <0>;
- };
-
- port@1 {
- label = "port1";
- reg = <1>;
- };
-
- port@2 {
- label = "port2";
- reg = <2>;
- };
- port@3 {
- label = "port3";
- reg = <3>;
- };
+ gpiobs: gpiobs {
+ function = "gpio_b";
+ groups = "gpio_b_0_grp", "gpio_b_1_grp", "gpio_b_2_grp",
+ "gpio_b_3_grp";
+ };
- port@4 {
- label = "port4";
- reg = <4>;
- };
+ pwmc: pwmc {
+ function = "pwm";
+ groups = "pwm0_grp", "pwm1_grp", "pwm2_grp", "pwm3_grp";
+ };
- port@5 {
- ethernet = <&amac0>;
- label = "cpu";
- reg = <5>;
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
+ emmc_sel: emmc_sel {
+ function = "emmc";
+ groups = "emmc_grp";
};
};
+&pwm {
+ status = "okay";
+};
+
&qspi {
bspi-sel = <0>;
flash: m25p80@0 {
@@ -215,6 +191,64 @@
status = "okay";
};
+/*
+ * By default the sd slot is functional. For emmc to work add "<&emmc_sel>"
+ * and delete "<&nand_sel>" in "pinctrl-0" property of pinctrl node. Remove the
+ * bus-width property here and disable the nand node with status = "disabled";.
+ *
+ * Ex: pinctrl-0 = <&emmc_sel>, <&gpiobs>, <&pwmc>;
+ */
+&sdio {
+ bus-width = <4>;
+ no-1-8-v;
+ status = "ok";
+};
+
+&srab {
+ compatible = "brcm,bcm58625-srab", "brcm,nsp-srab";
+ status = "okay";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ label = "port0";
+ reg = <0>;
+ };
+
+ port@1 {
+ label = "port1";
+ reg = <1>;
+ };
+
+ port@2 {
+ label = "port2";
+ reg = <2>;
+ };
+
+ port@3 {
+ label = "port3";
+ reg = <3>;
+ };
+
+ port@4 {
+ label = "port4";
+ reg = <4>;
+ };
+
+ port@5 {
+ ethernet = <&amac0>;
+ label = "cpu";
+ reg = <5>;
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+};
+
&uart0 {
status = "okay";
};
--
2.7.4
^ permalink raw reply related [flat|nested] 15+ messages in thread[parent not found: <1481652831-2744-2-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
* Re: [PATCH 1/7] ARM: dts: NSP: DT Clean-ups
[not found] ` <1481652831-2744-2-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
@ 2017-01-06 17:47 ` Florian Fainelli
0 siblings, 0 replies; 15+ messages in thread
From: Florian Fainelli @ 2017-01-06 17:47 UTC (permalink / raw)
To: bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w, Jon Mason,
Rob Herring
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA
On Tue, 13 Dec 2016 13:13:45 -0500, Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
> The QSPI entry was added out of the sequental order that the rest of the
> DTSI file is in. Move it to make it fit in properly. Also, some other
> entries have been added in a non-alphabetical order in the DTS files,
> making them different from the other NSP DTS files. Move the relevant
> peices to make it match. Finally, remove errant new lines.
>
> Signed-off-by: Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
> ---
Applied, thanks!
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
[parent not found: <1481652831-2744-3-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
[parent not found: <1481652831-2744-4-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
* Re: [PATCH 3/7] ARM: dts: NSP: Add QSPI support to missing boards
[not found] ` <1481652831-2744-4-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
@ 2017-01-06 17:48 ` Florian Fainelli
0 siblings, 0 replies; 15+ messages in thread
From: Florian Fainelli @ 2017-01-06 17:48 UTC (permalink / raw)
To: bcm-kernel-feedback-list-dY08KVG/lbpWk0Htik3J/w, Jon Mason,
Rob Herring
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA
On Tue, 13 Dec 2016 13:13:47 -0500, Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org> wrote:
> QSPI device tree entries are present in bcm958625k, but missing from
> bcm958522er, bcm958525er, bcm958525xmc, bcm958622hr, bcm958623hr,
> bcm958625hr, and bcm988312hr. Duplicate the entry in bcm958625k for
> all of those that are missing it (as they are identical).
>
> Signed-off-by: Jon Mason <jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>
> ---
Applied, thanks!
--
Florian
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 15+ messages in thread
[parent not found: <1481652831-2744-5-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
[parent not found: <1481652831-2744-6-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
[parent not found: <1481652831-2744-7-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]
[parent not found: <1481652831-2744-8-git-send-email-jon.mason-dY08KVG/lbpWk0Htik3J/w@public.gmane.org>]