From: Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>
To: linux-fpga-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Alan Tull
<atull-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org>,
Moritz Fischer
<moritz.fischer-+aYTwkv1SeIAvxtiuMwx3w@public.gmane.org>,
Rob Herring <robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>,
Mark Rutland <mark.rutland-5wv7dgnIgG8@public.gmane.org>
Subject: [PATCH v2 2/2] fpga manager: Add Xilinx slave serial SPI driver
Date: Mon, 20 Feb 2017 15:25:24 +0100 [thread overview]
Message-ID: <1487600724-17607-3-git-send-email-agust@denx.de> (raw)
In-Reply-To: <1487600724-17607-1-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
The driver loads FPGA firmware over SPI, using the "slave serial"
configuration interface on Xilinx FPGAs.
Signed-off-by: Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>
---
This patch requires patch https://lkml.org/lkml/2017/2/15/667
for building
Changes in v2:
- rebased on v4.10
drivers/fpga/Kconfig | 7 ++
drivers/fpga/Makefile | 1 +
drivers/fpga/xilinx-spi.c | 181 ++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 189 insertions(+)
create mode 100644 drivers/fpga/xilinx-spi.c
diff --git a/drivers/fpga/Kconfig b/drivers/fpga/Kconfig
index ce861a2..6b42786 100644
--- a/drivers/fpga/Kconfig
+++ b/drivers/fpga/Kconfig
@@ -33,6 +33,13 @@ config FPGA_MGR_SOCFPGA_A10
help
FPGA manager driver support for Altera Arria10 SoCFPGA.
+config FPGA_MGR_XILINX_SPI
+ tristate "Xilinx Configuration over Slave Serial (SPI)"
+ depends on SPI
+ help
+ FPGA manager driver support for Xilinx FPGA configuration
+ over slave serial interface.
+
config FPGA_MGR_ZYNQ_FPGA
tristate "Xilinx Zynq FPGA"
depends on ARCH_ZYNQ || COMPILE_TEST
diff --git a/drivers/fpga/Makefile b/drivers/fpga/Makefile
index 8df07bc..7582c5a 100644
--- a/drivers/fpga/Makefile
+++ b/drivers/fpga/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_FPGA) += fpga-mgr.o
# FPGA Manager Drivers
obj-$(CONFIG_FPGA_MGR_SOCFPGA) += socfpga.o
obj-$(CONFIG_FPGA_MGR_SOCFPGA_A10) += socfpga-a10.o
+obj-$(CONFIG_FPGA_MGR_XILINX_SPI) += xilinx-spi.o
obj-$(CONFIG_FPGA_MGR_ZYNQ_FPGA) += zynq-fpga.o
# FPGA Bridge Drivers
diff --git a/drivers/fpga/xilinx-spi.c b/drivers/fpga/xilinx-spi.c
new file mode 100644
index 0000000..16b3fa2
--- /dev/null
+++ b/drivers/fpga/xilinx-spi.c
@@ -0,0 +1,181 @@
+/*
+ * Xilinx Spartan6 Slave Serial SPI Driver
+ *
+ * Copyright (C) 2017 DENX Software Engineering
+ *
+ * Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * Manage Xilinx FPGA firmware that is loaded over SPI using
+ * the slave serial configuration interface.
+ */
+
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/fpga/fpga-mgr.h>
+#include <linux/gpio/consumer.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/of.h>
+#include <linux/spi/spi.h>
+#include <linux/sizes.h>
+
+#define FPGA_MIN_CFG_WAIT_US 10
+
+struct xilinx_spi_conf {
+ struct spi_device *spi;
+ struct gpio_desc *prog_b;
+ struct gpio_desc *done;
+};
+
+static enum fpga_mgr_states xilinx_spi_state(struct fpga_manager *mgr)
+{
+ struct xilinx_spi_conf *conf = mgr->priv;
+
+ if (!gpiod_get_value(conf->done))
+ return FPGA_MGR_STATE_RESET;
+
+ return FPGA_MGR_STATE_UNKNOWN;
+}
+
+static int xilinx_spi_write_init(struct fpga_manager *mgr,
+ struct fpga_image_info *info,
+ const char *buf, size_t count)
+{
+ struct xilinx_spi_conf *conf = mgr->priv;
+
+ if (info->flags & FPGA_MGR_PARTIAL_RECONFIG) {
+ dev_err(&mgr->dev, "Partial reconfiguration not supported.\n");
+ return -EINVAL;
+ }
+
+ gpiod_set_value(conf->prog_b, 1);
+
+ udelay(1); /* min is 500 ns */
+
+ gpiod_set_value(conf->prog_b, 0);
+
+ if (gpiod_get_value(conf->done)) {
+ dev_err(&mgr->dev, "Unexpected DONE pin state...\n");
+ return -EIO;
+ }
+
+ /* program latency */
+ usleep_range(1000, 1500);
+ return 0;
+}
+
+static int xilinx_spi_write(struct fpga_manager *mgr, const char *buf,
+ size_t count)
+{
+ struct xilinx_spi_conf *conf = mgr->priv;
+ const char *fw_data = buf;
+ const char *fw_data_end = fw_data + count;
+
+ while (fw_data < fw_data_end) {
+ int ret;
+ size_t stride = min(fw_data_end - fw_data, SZ_4K);
+
+ ret = spi_write(conf->spi, fw_data, stride);
+ if (ret) {
+ dev_err(&mgr->dev, "SPI error in firmware write: %d\n",
+ ret);
+ return ret;
+ }
+ fw_data += stride;
+ }
+
+ return 0;
+}
+
+static int xilinx_spi_write_complete(struct fpga_manager *mgr,
+ struct fpga_image_info *info)
+{
+ struct xilinx_spi_conf *conf = mgr->priv;
+ int wait;
+
+ if (gpiod_get_value(conf->done))
+ return 0;
+
+ wait = info->config_complete_timeout_us / FPGA_MIN_CFG_WAIT_US;
+ if (info->config_complete_timeout_us % FPGA_MIN_CFG_WAIT_US)
+ wait += 1;
+
+ while (wait--) {
+ usleep_range(FPGA_MIN_CFG_WAIT_US, FPGA_MIN_CFG_WAIT_US + 5);
+
+ if (gpiod_get_value(conf->done))
+ return 0;
+ }
+
+ dev_err(&mgr->dev, "Timeout after config data transfer.\n");
+ return -ETIMEDOUT;
+}
+
+static const struct fpga_manager_ops xilinx_spi_ops = {
+ .state = xilinx_spi_state,
+ .write_init = xilinx_spi_write_init,
+ .write = xilinx_spi_write,
+ .write_complete = xilinx_spi_write_complete,
+};
+
+static int xilinx_spi_probe(struct spi_device *spi)
+{
+ struct xilinx_spi_conf *conf;
+
+ conf = devm_kzalloc(&spi->dev, sizeof(*conf), GFP_KERNEL);
+ if (!conf)
+ return -ENOMEM;
+
+ conf->spi = spi;
+
+ /* PROGRAM_B is active low */
+ conf->prog_b = devm_gpiod_get(&spi->dev, "prog_b", GPIOD_OUT_LOW);
+ if (IS_ERR(conf->prog_b)) {
+ dev_err(&spi->dev, "Failed to get PROGRAM_B gpio: %ld\n",
+ PTR_ERR(conf->prog_b));
+ return PTR_ERR(conf->prog_b);
+ }
+
+ conf->done = devm_gpiod_get(&spi->dev, "done", GPIOD_IN);
+ if (IS_ERR(conf->done)) {
+ dev_err(&spi->dev, "Failed to get DONE gpio: %ld\n",
+ PTR_ERR(conf->done));
+ return PTR_ERR(conf->done);
+ }
+
+ return fpga_mgr_register(&spi->dev, "Xilinx Slave Serial FPGA Manager",
+ &xilinx_spi_ops, conf);
+}
+
+static int xilinx_spi_remove(struct spi_device *spi)
+{
+ fpga_mgr_unregister(&spi->dev);
+
+ return 0;
+}
+
+static const struct of_device_id xlnx_spi_of_match[] = {
+ { .compatible = "xlnx,fpga-slave-serial", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, xlnx_spi_of_match);
+
+static struct spi_driver xilinx_slave_spi_driver = {
+ .driver = {
+ .name = "xlnx-slave-spi",
+ .owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(xlnx_spi_of_match),
+ },
+ .probe = xilinx_spi_probe,
+ .remove = xilinx_spi_remove,
+};
+
+module_spi_driver(xilinx_slave_spi_driver)
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>");
+MODULE_DESCRIPTION("Load Xilinx FPGA firmware over SPI");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-02-20 14:25 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-02-20 14:25 [PATCH v2 0/2] Xilinx Slave Serial FPGA Manager Anatolij Gustschin
[not found] ` <1487600724-17607-1-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
2017-02-20 14:25 ` [PATCH v2 1/2] dt: bindings: fpga: add xilinx slave-serial binding description Anatolij Gustschin
[not found] ` <1487600724-17607-2-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
2017-02-20 17:28 ` Moritz Fischer
2017-02-20 14:25 ` Anatolij Gustschin [this message]
[not found] ` <1487600724-17607-3-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
2017-02-20 17:27 ` [PATCH v2 2/2] fpga manager: Add Xilinx slave serial SPI driver Moritz Fischer
[not found] ` <CAAtXAHeO_+6ZXP51nxFgyLYR9cjqLrqmoYEniqXmZudF=3uhFA-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-02-20 20:05 ` Anatolij Gustschin
2017-02-21 14:01 ` Michal Simek
[not found] ` <2d412ae7-4163-9943-6d98-2d6387df7789-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2017-02-21 14:24 ` Anatolij Gustschin
2017-02-21 14:51 ` Michal Simek
[not found] ` <19e0b5d1-bbf6-25ac-2698-6074ebafcf05-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2017-02-21 15:17 ` Anatolij Gustschin
2017-02-21 15:27 ` Michal Simek
[not found] ` <ce0d7ba7-fa05-ad55-407c-3903553ace65-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2017-02-21 15:39 ` Anatolij Gustschin
2017-02-21 18:53 ` Michal Simek
[not found] ` <3a30638c-68f6-8c2b-95b7-c8c700fe4867-gjFFaj9aHVfQT0dZR+AlfA@public.gmane.org>
2017-02-21 20:24 ` Anatolij Gustschin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1487600724-17607-3-git-send-email-agust@denx.de \
--to=agust-ynqeqjnshbs@public.gmane.org \
--cc=atull-yzvPICuk2ABMcg4IHK0kFoH6Mc4MB0Vx@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-fpga-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=moritz.fischer-+aYTwkv1SeIAvxtiuMwx3w@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).