Re: [PATCH v2 2/2] arm64: dts: Add Mediatek SoC MT2712 and evaluation board dts and Makefile

[YT Shen <yt.shen@mediatek.com>]

On Wed, 2017-05-31 at 14:42 +0200, Matthias Brugger wrote:
> 
> On 31/05/17 13:39, YT Shen wrote:
> > This adds basic chip support for Mediatek 2712
> > 
> > Signed-off-by: YT Shen <yt.shen@mediatek.com>
> > ---
> >   arch/arm64/boot/dts/mediatek/Makefile       |   1 +
> >   arch/arm64/boot/dts/mediatek/mt2712-evb.dts |  39 +++++++
> >   arch/arm64/boot/dts/mediatek/mt2712e.dtsi   | 166 ++++++++++++++++++++++++++++
> >   3 files changed, 206 insertions(+)
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> >   create mode 100644 arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > 
> > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
> > index 9fbfd32..fcc0604 100644
> > --- a/arch/arm64/boot/dts/mediatek/Makefile
> > +++ b/arch/arm64/boot/dts/mediatek/Makefile
> > @@ -1,3 +1,4 @@
> > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt2712-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6755-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt6795-evb.dtb
> >   dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > new file mode 100644
> > index 0000000..e526c0f
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
> > @@ -0,0 +1,39 @@
> > +/*
> > + * Copyright (c) 2017 MediaTek Inc.
> > + * Author: YT Shen <yt.shen@mediatek.com>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > + */
> > +
> > +/dts-v1/;
> > +#include "mt2712e.dtsi"
> > +
> > +/ {
> > +	model = "MediaTek MT2712 evaluation board";
> > +	compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
> > +
> > +	aliases {
> > +		serial0 = &uart0;
> > +		serial1 = &uart1;
> > +		serial2 = &uart2;
> > +		serial3 = &uart3;
> > +		serial4 = &uart4;
> > +		serial5 = &uart5;
> > +	};
> 
> Just declare serial0 here, as you don't use the others.
Ok, will remove the others.

Sorry for the late reply.

> > +
> > +	memory@40000000 {
> > +		device_type = "memory";
> > +		reg = <0 0x40000000 0 0x80000000>;
> > +	};
> > +
> > +	chosen {
> > +		stdout-path = "serial0:921600n8";
> > +		linux,initrd-start = <0x45000000>;
> > +		linux,initrd-end   = <0x4a000000>;
> 
> initrd-start and end should be dynamically set by the bootloader and not 
> via a chosen node. Is your bootloader not able to do that?
OK, will remove initrd start and end later.
Yes, current bootloader I used is new development and it does not send
any parameters now

> 
> > +	};
> > +};
> > +
> > +&uart0 {
> > +	status = "okay";
> > +};
> > +
> > diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > new file mode 100644
> > index 0000000..6df0da9
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
> > @@ -0,0 +1,166 @@
> > +/*
> > + * Copyright (c) 2017 MediaTek Inc.
> > + * Author: YT Shen <yt.shen@mediatek.com>
> > + *
> > + * SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > + */
> > +
> > +#include <dt-bindings/interrupt-controller/irq.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > +	compatible = "mediatek,mt2712";
> > +	interrupt-parent = <&sysirq>;
> > +	#address-cells = <2>;
> > +	#size-cells = <2>;
> > +
> > +	cpus {
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +
> > +		cpu-map {
> > +			cluster0 {
> > +				core0 {
> > +					cpu = <&cpu0>;
> > +				};
> > +				core1 {
> > +					cpu = <&cpu1>;
> > +				};
> > +			};
> > +
> > +			cluster1 {
> > +				core0 {
> > +					cpu = <&cpu2>;
> > +				};
> > +			};
> > +		};
> > +
> > +		cpu0: cpu@0 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a35";
> 
> do you mean cortex-a53?
No, the cpu is cortex-a35.
Although I cannot find other cortex-a35 description in mainline kernel.

Thanks for the review.

yt.shen

> 
> > +			reg = <0x000>;
> > +		};
> > +
> > +		cpu1: cpu@1 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a35";
> 
> same here.
> 
> Regards,
> Matthias
> 
> > +			reg = <0x001>;
> > +			enable-method = "psci";
> > +		};
> > +
> > +		cpu2: cpu@200 {
> > +			device_type = "cpu";
> > +			compatible = "arm,cortex-a72";
> > +			reg = <0x200>;
> > +			enable-method = "psci";
> > +		};
> > +	};
> > +
> > +	psci {
> > +		compatible = "arm,psci-0.2";
> > +		method = "smc";
> > +	};
> > +
> > +	uart_clk: dummy26m {
> > +		compatible = "fixed-clock";
> > +		clock-frequency = <26000000>;
> > +		#clock-cells = <0>;
> > +	};
> > +
> > +	timer {
> > +		compatible = "arm,armv8-timer";
> > +		interrupt-parent = <&gic>;
> > +		interrupts = <GIC_PPI 13
> > +			      (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 14
> > +			      (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 11
> > +			      (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
> > +			     <GIC_PPI 10
> > +			      (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
> > +	};
> > +
> > +	soc {
> > +		#address-cells = <2>;
> > +		#size-cells = <2>;
> > +		compatible = "simple-bus";
> > +		ranges;
> > +
> > +		uart5: serial@1000f000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x1000f000 0 0x400>;
> > +			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +
> > +		sysirq: interrupt-controller@10220a80 {
> > +			compatible = "mediatek,mt2712-sysirq",
> > +				     "mediatek,mt6577-sysirq";
> > +			interrupt-controller;
> > +			#interrupt-cells = <3>;
> > +			interrupt-parent = <&gic>;
> > +			reg = <0 0x10220a80 0 0x40>;
> > +		};
> > +
> > +		gic: interrupt-controller@10510000 {
> > +			compatible = "arm,gic-400";
> > +			#interrupt-cells = <3>;
> > +			interrupt-parent = <&gic>;
> > +			interrupt-controller;
> > +			reg = <0 0x10510000 0 0x1000>,
> > +			      <0 0x10520000 0 0x1000>,
> > +			      <0 0x10540000 0 0x2000>,
> > +			      <0 0x10560000 0 0x2000>;
> > +			interrupts = <GIC_PPI 9
> > +				(GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_HIGH)>;
> > +		};
> > +
> > +		uart0: serial@11002000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11002000 0 0x400>;
> > +			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +
> > +		uart1: serial@11003000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11003000 0 0x400>;
> > +			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +
> > +		uart2: serial@11004000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11004000 0 0x400>;
> > +			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +
> > +		uart3: serial@11005000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11005000 0 0x400>;
> > +			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +
> > +		uart4: serial@11019000 {
> > +			compatible = "mediatek,mt2712-uart",
> > +				     "mediatek,mt6577-uart";
> > +			reg = <0 0x11019000 0 0x400>;
> > +			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_LOW>;
> > +			clocks = <&uart_clk>;
> > +			status = "disabled";
> > +		};
> > +	};
> > +};
> > +
> >