From: Varadarajan Narayanan <varada@codeaurora.org>
To: bhelgaas@google.com, robh+dt@kernel.org, mark.rutland@arm.com,
svarbanov@mm-sol.com, kishon@ti.com, sboyd@codeaurora.org,
vivek.gautam@codeaurora.org, fengguang.wu@intel.com,
weiyongjun1@huawei.com, linux-pci@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-arm-msm@vger.kernel.org
Cc: Varadarajan Narayanan <varada@codeaurora.org>,
smuthayy <smuthayy@codeaurora.org>
Subject: [PATCH v3 5/8] phy: qcom-qmp: Add support for IPQ8074
Date: Thu, 20 Jul 2017 11:04:37 +0530 [thread overview]
Message-ID: <1500528880-25804-6-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1500528880-25804-1-git-send-email-varada@codeaurora.org>
Add definitions required to enable QMP phy support for IPQ8074.
Signed-off-by: smuthayy <smuthayy@codeaurora.org>
Signed-off-by: Varadarajan Narayanan <varada@codeaurora.org>
---
drivers/phy/qualcomm/phy-qcom-qmp.c | 135 ++++++++++++++++++++++++++++++++++++
1 file changed, 135 insertions(+)
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 000ad1c..9019f66 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -59,6 +59,7 @@
#define QSERDES_COM_PLL_RCTRL_MODE1 0x088
#define QSERDES_COM_PLL_CCTRL_MODE0 0x090
#define QSERDES_COM_PLL_CCTRL_MODE1 0x094
+#define QSERDES_COM_BIAS_EN_CTRL_BY_PSM 0x0a8
#define QSERDES_COM_SYSCLK_EN_SEL 0x0ac
#define QSERDES_COM_RESETSM_CNTRL 0x0b4
#define QSERDES_COM_RESTRIM_CTRL 0x0bc
@@ -143,6 +144,11 @@
#define QPHY_LOCK_DETECT_CONFIG3 0x88
#define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK 0xa0
#define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK 0xa4
+#define QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB 0x1A8
+#define QPHY_OSC_DTCT_ACTIONS 0x1AC
+#define QPHY_RX_SIGDET_LVL 0x1D8
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB 0x1DC
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB 0x1E0
/* QPHY_SW_RESET bit */
#define SW_RESET BIT(0)
@@ -224,6 +230,17 @@ enum qphy_reg_layout {
[QPHY_PCS_READY_STATUS] = 0x174,
};
+static const unsigned int ipq8074_pciephy_regs_layout[] = {
+ [QPHY_COM_SW_RESET] = 0x800,
+ [QPHY_COM_POWER_DOWN_CONTROL] = 0x804,
+ [QPHY_COM_START_CONTROL] = 0x808,
+ [QPHY_COM_PCS_READY_STATUS] = QPHY_REG_INVAL,
+ [QPHY_PLL_LOCK_CHK_DLY_TIME] = 0xa8,
+ [QPHY_SW_RESET] = 0x00,
+ [QPHY_START_CTRL] = 0x08,
+ [QPHY_PCS_READY_STATUS] = 0x174,
+};
+
static const unsigned int usb3phy_regs_layout[] = {
[QPHY_FLL_CNTRL1] = 0xc0,
[QPHY_FLL_CNTRL2] = 0xc4,
@@ -582,6 +599,121 @@ static inline void qphy_clrbits(void __iomem *base, u32 offset, u32 val)
.mask_pcs_ready = PHYSTATUS,
};
+static const struct qmp_phy_init_tbl ipq8074_pcie_serdes_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x18),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0xf),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x6),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0xf),
+ QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x3),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0xD),
+ QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xD04),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0xb),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+ QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+ QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CTRL_BY_PSM, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0xa),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
+ QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x7),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_tx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+ QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x6),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RES_CODE_LANE_OFFSET, 0x2),
+ QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_rx_tbl[] = {
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
+ QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x1),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x0),
+ QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x4),
+ QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x4),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = {
+ QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x4),
+ QMP_PHY_INIT_CFG(QPHY_OSC_DTCT_ACTIONS, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB, 0x40),
+ QMP_PHY_INIT_CFG(QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB, 0x0),
+ QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x40),
+ QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x73),
+ QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_LVL, 0x99),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M6DB_V0, 0x15),
+ QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0xe),
+ QMP_PHY_INIT_CFG_L(QPHY_SW_RESET, 0x0),
+ QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
+};
+
+/* list of resets */
+static const char * const ipq8074_pciephy_reset_l[] = {
+ "phy", "phy_phy",
+};
+
+static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
+ .type = PHY_TYPE_PCIE,
+ .nlanes = 1,
+
+ .serdes_tbl = ipq8074_pcie_serdes_tbl,
+ .serdes_tbl_num = ARRAY_SIZE(ipq8074_pcie_serdes_tbl),
+ .tx_tbl = ipq8074_pcie_tx_tbl,
+ .tx_tbl_num = ARRAY_SIZE(ipq8074_pcie_tx_tbl),
+ .rx_tbl = ipq8074_pcie_rx_tbl,
+ .rx_tbl_num = ARRAY_SIZE(ipq8074_pcie_rx_tbl),
+ .pcs_tbl = ipq8074_pcie_pcs_tbl,
+ .pcs_tbl_num = ARRAY_SIZE(ipq8074_pcie_pcs_tbl),
+ .clk_list = NULL,
+ .num_clks = 0,
+ .reset_list = ipq8074_pciephy_reset_l,
+ .num_resets = ARRAY_SIZE(ipq8074_pciephy_reset_l),
+ .vreg_list = NULL,
+ .num_vregs = 0,
+ .regs = ipq8074_pciephy_regs_layout,
+
+ .start_ctrl = SERDES_START | PCS_START,
+ .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
+ .mask_pcs_ready = PHYSTATUS,
+
+ .has_phy_com_ctrl = true,
+ .has_lane_rst = false,
+ .has_pwrdn_delay = true,
+ .pwrdn_delay_min = 995, /* us */
+ .pwrdn_delay_max = 1005, /* us */
+};
+
static void qcom_qmp_phy_configure(void __iomem *base,
const unsigned int *regs,
const struct qmp_phy_init_tbl tbl[],
@@ -1047,6 +1179,9 @@ int qcom_qmp_phy_create(struct device *dev, struct device_node *np, int id)
}, {
.compatible = "qcom,msm8996-qmp-usb3-phy",
.data = &msm8996_usb3phy_cfg,
+ }, {
+ .compatible = "qcom,ipq8074-qmp-pcie-phy",
+ .data = &ipq8074_pciephy_cfg,
},
{ },
};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2017-07-20 5:34 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-20 5:34 [PATCH v3 0/8] Add support for IPQ8074 PCIe phy and controller Varadarajan Narayanan
2017-07-20 5:34 ` [PATCH v3 1/8] dt-bindings: phy: qmp: Add output-clock-names Varadarajan Narayanan
2017-07-20 5:34 ` [PATCH v3 2/8] dt-bindings: phy: qmp: Add support for QMP phy in IPQ8074 Varadarajan Narayanan
2017-07-20 5:34 ` [PATCH v3 3/8] phy: qcom-qmp: Fix phy pipe clock name Varadarajan Narayanan
2017-07-21 8:01 ` Vivek Gautam
2017-07-20 5:34 ` [PATCH v3 4/8] phy: qcom-qmp: Handle unavailable registers Varadarajan Narayanan
2017-07-20 5:34 ` Varadarajan Narayanan [this message]
2017-07-20 5:34 ` [PATCH v3 6/8] PCI: dwc: qcom: Use block IP version for operations Varadarajan Narayanan
2017-07-20 5:34 ` [PATCH v3 7/8] dt-bindings: pci: qcom: Add support for IPQ8074 Varadarajan Narayanan
2017-07-20 5:34 ` [PATCH v3 8/8] PCI: dwc: qcom: Add support for IPQ8074 PCIe controller Varadarajan Narayanan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1500528880-25804-6-git-send-email-varada@codeaurora.org \
--to=varada@codeaurora.org \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=fengguang.wu@intel.com \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
--cc=smuthayy@codeaurora.org \
--cc=svarbanov@mm-sol.com \
--cc=vivek.gautam@codeaurora.org \
--cc=weiyongjun1@huawei.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).