From: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
To: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Varadarajan Narayanan
<varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>,
Matthew McClintock
<mmcclint-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Subject: [PATCH v5 10/14] spi: qup: allow block mode to generate multiple transactions
Date: Mon, 24 Jul 2017 13:17:21 +0530 [thread overview]
Message-ID: <1500882445-29008-11-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
This let's you write more to the SPI bus than 64K-1 which is important
if the block size of a SPI device is >= 64K or some other device wants
to do something larger.
This has the benefit of completely removing spi_message from the spi-qup
transactions
Signed-off-by: Matthew McClintock <mmcclint-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Signed-off-by: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
drivers/spi/spi-qup.c | 128 +++++++++++++++++++++++++++++++-------------------
1 file changed, 80 insertions(+), 48 deletions(-)
diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index b2bda47..67e7463 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -120,7 +120,7 @@
#define SPI_NUM_CHIPSELECTS 4
-#define SPI_MAX_DMA_XFER (SZ_64K - 64)
+#define SPI_MAX_XFER (SZ_64K - 64)
/* high speed mode is when bus rate is greater then 26MHz */
#define SPI_HS_MIN_RATE 26000000
@@ -149,6 +149,8 @@ struct spi_qup {
int n_words;
int tx_bytes;
int rx_bytes;
+ const u8 *tx_buf;
+ u8 *rx_buf;
int qup_v1;
int mode;
@@ -173,6 +175,12 @@ static inline bool spi_qup_is_dma_xfer(int mode)
return false;
}
+/* get's the transaction size length */
+static inline unsigned int spi_qup_len(struct spi_qup *controller)
+{
+ return controller->n_words * controller->w_size;
+}
+
static inline bool spi_qup_is_valid_state(struct spi_qup *controller)
{
u32 opstate = readl_relaxed(controller->base + QUP_STATE);
@@ -225,10 +233,9 @@ static int spi_qup_set_state(struct spi_qup *controller, u32 state)
return 0;
}
-static void spi_qup_read_from_fifo(struct spi_qup *controller,
- struct spi_transfer *xfer, u32 num_words)
+static void spi_qup_read_from_fifo(struct spi_qup *controller, u32 num_words)
{
- u8 *rx_buf = xfer->rx_buf;
+ u8 *rx_buf = controller->rx_buf;
int i, shift, num_bytes;
u32 word;
@@ -236,8 +243,9 @@ static void spi_qup_read_from_fifo(struct spi_qup *controller,
word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
- num_bytes = min_t(int, xfer->len - controller->rx_bytes,
- controller->w_size);
+ num_bytes = min_t(int, spi_qup_len(controller) -
+ controller->rx_bytes,
+ controller->w_size);
if (!rx_buf) {
controller->rx_bytes += num_bytes;
@@ -258,13 +266,12 @@ static void spi_qup_read_from_fifo(struct spi_qup *controller,
}
}
-static void spi_qup_read(struct spi_qup *controller,
- struct spi_transfer *xfer)
+static void spi_qup_read(struct spi_qup *controller)
{
u32 remainder, words_per_block, num_words;
bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
- remainder = DIV_ROUND_UP(xfer->len - controller->rx_bytes,
+ remainder = DIV_ROUND_UP(spi_qup_len(controller) - controller->rx_bytes,
controller->w_size);
words_per_block = controller->in_blk_sz >> 2;
@@ -285,7 +292,7 @@ static void spi_qup_read(struct spi_qup *controller,
}
/* read up to the maximum transfer size available */
- spi_qup_read_from_fifo(controller, xfer, num_words);
+ spi_qup_read_from_fifo(controller, num_words);
remainder -= num_words;
@@ -307,18 +314,18 @@ static void spi_qup_read(struct spi_qup *controller,
}
-static void spi_qup_write_to_fifo(struct spi_qup *controller,
- struct spi_transfer *xfer, u32 num_words)
+static void spi_qup_write_to_fifo(struct spi_qup *controller, u32 num_words)
{
- const u8 *tx_buf = xfer->tx_buf;
+ const u8 *tx_buf = controller->tx_buf;
int i, num_bytes;
u32 word, data;
for (; num_words; num_words--) {
word = 0;
- num_bytes = min_t(int, xfer->len - controller->tx_bytes,
- controller->w_size);
+ num_bytes = min_t(int, spi_qup_len(controller) -
+ controller->tx_bytes,
+ controller->w_size);
if (tx_buf)
for (i = 0; i < num_bytes; i++) {
data = tx_buf[controller->tx_bytes + i];
@@ -338,13 +345,12 @@ static void spi_qup_dma_done(void *data)
complete(&qup->done);
}
-static void spi_qup_write(struct spi_qup *controller,
- struct spi_transfer *xfer)
+static void spi_qup_write(struct spi_qup *controller)
{
bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
u32 remainder, words_per_block, num_words;
- remainder = DIV_ROUND_UP(xfer->len - controller->tx_bytes,
+ remainder = DIV_ROUND_UP(spi_qup_len(controller) - controller->tx_bytes,
controller->w_size);
words_per_block = controller->out_blk_sz >> 2;
@@ -364,7 +370,7 @@ static void spi_qup_write(struct spi_qup *controller,
num_words = 1;
}
- spi_qup_write_to_fifo(controller, xfer, num_words);
+ spi_qup_write_to_fifo(controller, num_words);
remainder -= num_words;
@@ -474,36 +480,62 @@ static int spi_qup_do_pio(struct spi_device *spi, struct spi_transfer *xfer,
{
struct spi_master *master = spi->master;
struct spi_qup *qup = spi_master_get_devdata(master);
- int ret;
+ int ret, n_words, iterations, offset = 0;
- ret = spi_qup_io_config(spi, xfer);
- if (ret)
- return ret;
+ n_words = qup->n_words;
+ iterations = n_words / SPI_MAX_XFER; /* round down */
+ qup->rx_buf = xfer->rx_buf;
+ qup->tx_buf = xfer->tx_buf;
- ret = spi_qup_set_state(qup, QUP_STATE_RUN);
- if (ret) {
- dev_warn(qup->dev, "cannot set RUN state\n");
- return ret;
- }
+ do {
+ if (iterations)
+ qup->n_words = SPI_MAX_XFER;
+ else
+ qup->n_words = n_words % SPI_MAX_XFER;
- ret = spi_qup_set_state(qup, QUP_STATE_PAUSE);
- if (ret) {
- dev_warn(qup->dev, "cannot set PAUSE state\n");
- return ret;
- }
+ if (qup->tx_buf && offset)
+ qup->tx_buf = xfer->tx_buf + offset * SPI_MAX_XFER;
- if (qup->mode == QUP_IO_M_MODE_FIFO)
- spi_qup_write(qup, xfer);
+ if (qup->rx_buf && offset)
+ qup->rx_buf = xfer->rx_buf + offset * SPI_MAX_XFER;
- ret = spi_qup_set_state(qup, QUP_STATE_RUN);
- if (ret) {
- dev_warn(qup->dev, "%s(%d): cannot set RUN state\n",
- __func__, __LINE__);
- return ret;
- }
+ /*
+ * if the transaction is small enough, we need
+ * to fallback to FIFO mode
+ */
+ if (qup->n_words <= (qup->in_fifo_sz / sizeof(u32)))
+ qup->mode = QUP_IO_M_MODE_FIFO;
- if (!wait_for_completion_timeout(&qup->done, timeout))
- return -ETIMEDOUT;
+ ret = spi_qup_io_config(spi, xfer);
+ if (ret)
+ return ret;
+
+ ret = spi_qup_set_state(qup, QUP_STATE_RUN);
+ if (ret) {
+ dev_warn(qup->dev, "cannot set RUN state\n");
+ return ret;
+ }
+
+ ret = spi_qup_set_state(qup, QUP_STATE_PAUSE);
+ if (ret) {
+ dev_warn(qup->dev, "cannot set PAUSE state\n");
+ return ret;
+ }
+
+ if (qup->mode == QUP_IO_M_MODE_FIFO)
+ spi_qup_write(qup);
+
+ ret = spi_qup_set_state(qup, QUP_STATE_RUN);
+ if (ret) {
+ dev_warn(qup->dev, "cannot set RUN state\n");
+ return ret;
+ }
+
+ if (!wait_for_completion_timeout(&qup->done, timeout))
+ return -ETIMEDOUT;
+
+ offset++;
+ } while (iterations--);
return 0;
}
@@ -511,7 +543,6 @@ static int spi_qup_do_pio(struct spi_device *spi, struct spi_transfer *xfer,
static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
{
struct spi_qup *controller = dev_id;
- struct spi_transfer *xfer = controller->xfer;
u32 opflags, qup_err, spi_err;
int error = 0;
@@ -548,10 +579,10 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
} else {
if (opflags & QUP_OP_IN_SERVICE_FLAG)
- spi_qup_read(controller, xfer);
+ spi_qup_read(controller);
if (opflags & QUP_OP_OUT_SERVICE_FLAG)
- spi_qup_write(controller, xfer);
+ spi_qup_write(controller);
}
if ((opflags & QUP_OP_MAX_INPUT_DONE_FLAG) || error)
@@ -758,7 +789,8 @@ static int spi_qup_transfer_one(struct spi_master *master,
return ret;
timeout = DIV_ROUND_UP(xfer->speed_hz, MSEC_PER_SEC);
- timeout = DIV_ROUND_UP(xfer->len * 8, timeout);
+ timeout = DIV_ROUND_UP(min_t(unsigned long, SPI_MAX_XFER,
+ xfer->len) * 8, timeout);
timeout = 100 * msecs_to_jiffies(timeout);
reinit_completion(&controller->done);
@@ -972,7 +1004,7 @@ static int spi_qup_probe(struct platform_device *pdev)
master->dev.of_node = pdev->dev.of_node;
master->auto_runtime_pm = true;
master->dma_alignment = dma_get_cache_alignment();
- master->max_dma_len = SPI_MAX_DMA_XFER;
+ master->max_dma_len = SPI_MAX_XFER;
platform_set_drvdata(pdev, master);
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-07-24 7:47 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-07-24 7:47 [PATCH v5 00/14] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 01/14] spi: qup: Enable chip select support Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 04/14] spi: qup: Place the QUP in run mode before DMA Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Place the QUP in run mode before DMA" to the spi tree Mark Brown
2017-07-24 7:47 ` [PATCH v5 06/14] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 08/14] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: refactor spi_qup_io_config into two functions" to the spi tree Mark Brown
[not found] ` <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-24 7:47 ` [PATCH v5 02/14] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 03/14] spi: qup: Add completion timeout Varadarajan Narayanan
2017-07-27 8:30 ` kbuild test robot
2017-07-24 7:47 ` [PATCH v5 05/14] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Fix error handling in spi_qup_prep_sg" to the spi tree Mark Brown
2017-07-24 7:47 ` [PATCH v5 07/14] spi: qup: Do block sized read/write in block mode Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: Do block sized read/write in block mode" to the spi tree Mark Brown
2017-07-24 7:47 ` [PATCH v5 09/14] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-07-24 7:47 ` Varadarajan Narayanan [this message]
2017-08-08 11:18 ` Applied "spi: qup: allow block mode to generate multiple transactions" to the spi tree Mark Brown
2017-07-24 7:47 ` [PATCH v5 11/14] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-08-08 11:18 ` Applied "spi: qup: refactor spi_qup_prep_sg" to the spi tree Mark Brown
2017-07-24 7:47 ` [PATCH v5 12/14] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 13/14] spi: qup: Ensure done detection Varadarajan Narayanan
2017-07-24 7:47 ` [PATCH v5 14/14] spi: qup: Fix QUP version identify method Varadarajan Narayanan
[not found] ` <1500882445-29008-15-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-25 2:52 ` kbuild test robot
2017-08-08 11:17 ` Applied "spi: qup: Fix QUP version identify method" to the spi tree Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1500882445-29008-11-git-send-email-varada@codeaurora.org \
--to=varada-sgv2jx0feol9jmxxk+q4oq@public.gmane.org \
--cc=andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=mmcclint-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).