devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
To: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	mark.rutland-5wv7dgnIgG8@public.gmane.org,
	andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
	david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org,
	linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
Subject: [PATCH v5 07/14] spi: qup: Do block sized read/write in block mode
Date: Mon, 24 Jul 2017 13:17:18 +0530	[thread overview]
Message-ID: <1500882445-29008-8-git-send-email-varada@codeaurora.org> (raw)
In-Reply-To: <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>

This patch corrects the behavior of the BLOCK
transactions.  During block transactions, the controller
must be read/written to in block size transactions.

Signed-off-by: Andy Gross <andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Signed-off-by: Varadarajan Narayanan <varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
---
 drivers/spi/spi-qup.c | 151 +++++++++++++++++++++++++++++++++++++++-----------
 1 file changed, 119 insertions(+), 32 deletions(-)

diff --git a/drivers/spi/spi-qup.c b/drivers/spi/spi-qup.c
index 5e6f7e5..d819f87 100644
--- a/drivers/spi/spi-qup.c
+++ b/drivers/spi/spi-qup.c
@@ -82,6 +82,8 @@
 #define QUP_IO_M_MODE_BAM		3
 
 /* QUP_OPERATIONAL fields */
+#define QUP_OP_IN_BLOCK_READ_REQ	BIT(13)
+#define QUP_OP_OUT_BLOCK_WRITE_REQ	BIT(12)
 #define QUP_OP_MAX_INPUT_DONE_FLAG	BIT(11)
 #define QUP_OP_MAX_OUTPUT_DONE_FLAG	BIT(10)
 #define QUP_OP_IN_SERVICE_FLAG		BIT(9)
@@ -154,6 +156,13 @@ struct spi_qup {
 	struct dma_slave_config	tx_conf;
 };
 
+static inline bool spi_qup_is_flag_set(struct spi_qup *controller, u32 flag)
+{
+	u32 opflag = readl_relaxed(controller->base + QUP_OPERATIONAL);
+
+	return (opflag & flag) != 0;
+}
+
 static inline bool spi_qup_is_dma_xfer(int mode)
 {
 	if (mode == QUP_IO_M_MODE_DMOV || mode == QUP_IO_M_MODE_BAM)
@@ -214,29 +223,26 @@ static int spi_qup_set_state(struct spi_qup *controller, u32 state)
 	return 0;
 }
 
-static void spi_qup_fifo_read(struct spi_qup *controller,
-			    struct spi_transfer *xfer)
+static void spi_qup_read_from_fifo(struct spi_qup *controller,
+	struct spi_transfer *xfer, u32 num_words)
 {
 	u8 *rx_buf = xfer->rx_buf;
-	u32 word, state;
-	int idx, shift, w_size;
+	int i, shift, num_bytes;
+	u32 word;
 
-	w_size = controller->w_size;
-
-	while (controller->rx_bytes < xfer->len) {
-
-		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
-		if (0 == (state & QUP_OP_IN_FIFO_NOT_EMPTY))
-			break;
+	for (; num_words; num_words--) {
 
 		word = readl_relaxed(controller->base + QUP_INPUT_FIFO);
 
+		num_bytes = min_t(int, xfer->len - controller->rx_bytes,
+					controller->w_size);
+
 		if (!rx_buf) {
-			controller->rx_bytes += w_size;
+			controller->rx_bytes += num_bytes;
 			continue;
 		}
 
-		for (idx = 0; idx < w_size; idx++, controller->rx_bytes++) {
+		for (i = 0; i < num_bytes; i++, controller->rx_bytes++) {
 			/*
 			 * The data format depends on bytes per SPI word:
 			 *  4 bytes: 0x12345678
@@ -244,38 +250,80 @@ static void spi_qup_fifo_read(struct spi_qup *controller,
 			 *  1 byte : 0x00000012
 			 */
 			shift = BITS_PER_BYTE;
-			shift *= (w_size - idx - 1);
+			shift *= (controller->w_size - i - 1);
 			rx_buf[controller->rx_bytes] = word >> shift;
 		}
 	}
 }
 
-static void spi_qup_fifo_write(struct spi_qup *controller,
+static void spi_qup_read(struct spi_qup *controller,
 			    struct spi_transfer *xfer)
 {
-	const u8 *tx_buf = xfer->tx_buf;
-	u32 word, state, data;
-	int idx, w_size;
+	u32 remainder, words_per_block, num_words;
+	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
+
+	remainder = DIV_ROUND_UP(xfer->len - controller->rx_bytes,
+				 controller->w_size);
+	words_per_block = controller->in_blk_sz >> 2;
+
+	do {
+		/* ACK by clearing service flag */
+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+		if (is_block_mode) {
+			num_words = (remainder > words_per_block) ?
+					words_per_block : remainder;
+		} else {
+			if (!spi_qup_is_flag_set(controller,
+						 QUP_OP_IN_FIFO_NOT_EMPTY))
+				break;
 
-	w_size = controller->w_size;
+			num_words = 1;
+		}
 
-	while (controller->tx_bytes < xfer->len) {
+		/* read up to the maximum transfer size available */
+		spi_qup_read_from_fifo(controller, xfer, num_words);
 
-		state = readl_relaxed(controller->base + QUP_OPERATIONAL);
-		if (state & QUP_OP_OUT_FIFO_FULL)
+		remainder -= num_words;
+
+		/* if block mode, check to see if next block is available */
+		if (is_block_mode && !spi_qup_is_flag_set(controller,
+					QUP_OP_IN_BLOCK_READ_REQ))
 			break;
 
+	} while (remainder);
+
+	/*
+	 * Due to extra stickiness of the QUP_OP_IN_SERVICE_FLAG during block
+	 * mode reads, it has to be cleared again at the very end
+	 */
+	if (is_block_mode && spi_qup_is_flag_set(controller,
+				QUP_OP_MAX_INPUT_DONE_FLAG))
+		writel_relaxed(QUP_OP_IN_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+}
+
+static void spi_qup_write_to_fifo(struct spi_qup *controller,
+	struct spi_transfer *xfer, u32 num_words)
+{
+	const u8 *tx_buf = xfer->tx_buf;
+	int i, num_bytes;
+	u32 word, data;
+
+	for (; num_words; num_words--) {
 		word = 0;
-		for (idx = 0; idx < w_size; idx++, controller->tx_bytes++) {
 
-			if (!tx_buf) {
-				controller->tx_bytes += w_size;
-				break;
+		num_bytes = min_t(int, xfer->len - controller->tx_bytes,
+				    controller->w_size);
+		if (tx_buf)
+			for (i = 0; i < num_bytes; i++) {
+				data = tx_buf[controller->tx_bytes + i];
+				word |= data << (BITS_PER_BYTE * (3 - i));
 			}
 
-			data = tx_buf[controller->tx_bytes];
-			word |= data << (BITS_PER_BYTE * (3 - idx));
-		}
+		controller->tx_bytes += num_bytes;
 
 		writel_relaxed(word, controller->base + QUP_OUTPUT_FIFO);
 	}
@@ -288,6 +336,44 @@ static void spi_qup_dma_done(void *data)
 	complete(&qup->done);
 }
 
+static void spi_qup_write(struct spi_qup *controller,
+			    struct spi_transfer *xfer)
+{
+	bool is_block_mode = controller->mode == QUP_IO_M_MODE_BLOCK;
+	u32 remainder, words_per_block, num_words;
+
+	remainder = DIV_ROUND_UP(xfer->len - controller->tx_bytes,
+				 controller->w_size);
+	words_per_block = controller->out_blk_sz >> 2;
+
+	do {
+		/* ACK by clearing service flag */
+		writel_relaxed(QUP_OP_OUT_SERVICE_FLAG,
+			       controller->base + QUP_OPERATIONAL);
+
+		if (is_block_mode) {
+			num_words = (remainder > words_per_block) ?
+				words_per_block : remainder;
+		} else {
+			if (spi_qup_is_flag_set(controller,
+						QUP_OP_OUT_FIFO_FULL))
+				break;
+
+			num_words = 1;
+		}
+
+		spi_qup_write_to_fifo(controller, xfer, num_words);
+
+		remainder -= num_words;
+
+		/* if block mode, check to see if next block is available */
+		if (is_block_mode && !spi_qup_is_flag_set(controller,
+					QUP_OP_OUT_BLOCK_WRITE_REQ))
+			break;
+
+	} while (remainder);
+}
+
 static int spi_qup_prep_sg(struct spi_master *master, struct spi_transfer *xfer,
 			   enum dma_transfer_direction dir,
 			   dma_async_tx_callback callback)
@@ -393,7 +479,8 @@ static int spi_qup_do_pio(struct spi_master *master, struct spi_transfer *xfer,
 		return ret;
 	}
 
-	spi_qup_fifo_write(qup, xfer);
+	if (qup->mode == QUP_IO_M_MODE_FIFO)
+		spi_qup_write(qup, xfer);
 
 	ret = spi_qup_set_state(qup, QUP_STATE_RUN);
 	if (ret) {
@@ -448,10 +535,10 @@ static irqreturn_t spi_qup_qup_irq(int irq, void *dev_id)
 		writel_relaxed(opflags, controller->base + QUP_OPERATIONAL);
 	} else {
 		if (opflags & QUP_OP_IN_SERVICE_FLAG)
-			spi_qup_fifo_read(controller, xfer);
+			spi_qup_read(controller, xfer);
 
 		if (opflags & QUP_OP_OUT_SERVICE_FLAG)
-			spi_qup_fifo_write(controller, xfer);
+			spi_qup_write(controller, xfer);
 	}
 
 	if ((opflags & QUP_OP_MAX_INPUT_DONE_FLAG) || error)
-- 
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum, hosted by The Linux Foundation

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

  parent reply	other threads:[~2017-07-24  7:47 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-07-24  7:47 [PATCH v5 00/14] spi: qup: Fixes and add support for >64k transfers Varadarajan Narayanan
2017-07-24  7:47 ` [PATCH v5 01/14] spi: qup: Enable chip select support Varadarajan Narayanan
     [not found] ` <1500882445-29008-1-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-24  7:47   ` [PATCH v5 02/14] spi: qup: Setup DMA mode correctly Varadarajan Narayanan
2017-07-24  7:47   ` [PATCH v5 03/14] spi: qup: Add completion timeout Varadarajan Narayanan
2017-07-27  8:30     ` kbuild test robot
2017-07-24  7:47   ` [PATCH v5 05/14] spi: qup: Fix error handling in spi_qup_prep_sg Varadarajan Narayanan
2017-08-08 11:18     ` Applied "spi: qup: Fix error handling in spi_qup_prep_sg" to the spi tree Mark Brown
2017-07-24  7:47   ` Varadarajan Narayanan [this message]
2017-08-08 11:18     ` Applied "spi: qup: Do block sized read/write in block mode" " Mark Brown
2017-07-24  7:47   ` [PATCH v5 09/14] spi: qup: call io_config in mode specific function Varadarajan Narayanan
2017-07-24  7:47   ` [PATCH v5 10/14] spi: qup: allow block mode to generate multiple transactions Varadarajan Narayanan
2017-08-08 11:18     ` Applied "spi: qup: allow block mode to generate multiple transactions" to the spi tree Mark Brown
2017-07-24  7:47   ` [PATCH v5 11/14] spi: qup: refactor spi_qup_prep_sg Varadarajan Narayanan
2017-08-08 11:18     ` Applied "spi: qup: refactor spi_qup_prep_sg" to the spi tree Mark Brown
2017-07-24  7:47   ` [PATCH v5 12/14] spi: qup: allow multiple DMA transactions per spi xfer Varadarajan Narayanan
2017-07-24  7:47 ` [PATCH v5 04/14] spi: qup: Place the QUP in run mode before DMA Varadarajan Narayanan
2017-08-08 11:18   ` Applied "spi: qup: Place the QUP in run mode before DMA" to the spi tree Mark Brown
2017-07-24  7:47 ` [PATCH v5 06/14] spi: qup: Fix transaction done signaling Varadarajan Narayanan
2017-07-24  7:47 ` [PATCH v5 08/14] spi: qup: refactor spi_qup_io_config into two functions Varadarajan Narayanan
2017-08-08 11:18   ` Applied "spi: qup: refactor spi_qup_io_config into two functions" to the spi tree Mark Brown
2017-07-24  7:47 ` [PATCH v5 13/14] spi: qup: Ensure done detection Varadarajan Narayanan
2017-07-24  7:47 ` [PATCH v5 14/14] spi: qup: Fix QUP version identify method Varadarajan Narayanan
     [not found]   ` <1500882445-29008-15-git-send-email-varada-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
2017-07-25  2:52     ` kbuild test robot
2017-08-08 11:17     ` Applied "spi: qup: Fix QUP version identify method" to the spi tree Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1500882445-29008-8-git-send-email-varada@codeaurora.org \
    --to=varada-sgv2jx0feol9jmxxk+q4oq@public.gmane.org \
    --cc=andy.gross-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
    --cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=david.brown-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-arm-msm-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-soc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-spi-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
    --cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).