From: Eric Nelson <eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
To: linux-rtc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Cc: a.zummo-BfzFCNDTiLLj+vYz1yj4TQ@public.gmane.org,
alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org,
robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
otavio.salvador-fKevB0iiKLMBZ+LybsDmbA@public.gmane.org,
festevam-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org,
Eric Nelson <eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
Subject: [PATCH V2] rtc: add support for NXP PCF85363 real-time clock
Date: Wed, 11 Oct 2017 08:56:30 -0700 [thread overview]
Message-ID: <1507737390-27818-1-git-send-email-eric@nelint.com> (raw)
In-Reply-To: <CAOMZO5C_boginn88C7zgXSBaikx==5FHJrgaE1ewYUyUgGfnFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
Note that alarms are not currently implemented.
64 bytes of nvmem is supported and exposed in
sysfs (# is the instance number, starting with 0):
/sys/bus/nvmem/devices/pcf85363-#/nvmem
Signed-off-by: Eric Nelson <eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
---
V2 addresses a couple of issues highlighted by Fabio Estevam
1. Kconfig updated to select REGMAP_I2C
2. Switch to of_device_id from i2c_device_id for driver matching
Documentation/devicetree/bindings/rtc/pcf85363.txt | 16 ++
drivers/rtc/Kconfig | 13 ++
drivers/rtc/Makefile | 1 +
drivers/rtc/rtc-pcf85363.c | 221 +++++++++++++++++++++
4 files changed, 251 insertions(+)
create mode 100644 Documentation/devicetree/bindings/rtc/pcf85363.txt
create mode 100644 drivers/rtc/rtc-pcf85363.c
diff --git a/Documentation/devicetree/bindings/rtc/pcf85363.txt b/Documentation/devicetree/bindings/rtc/pcf85363.txt
new file mode 100644
index 0000000..5fddb9f
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/pcf85363.txt
@@ -0,0 +1,16 @@
+NXP PCF85363 Real Time Clock
+============================
+
+Required properties:
+- compatible: Should contain "nxp,pcf85363".
+- reg: I2C address for chip.
+
+Example:
+
+pcf85363: pcf85363@51 {
+ compatible = "nxp,pcf85363";
+ reg = <0x51>;
+};
+
+Note that alarms are not yet supported, so a specifier for
+"interrupts" will be ignored.
diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index e0e58f3..15306ed 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -433,6 +433,19 @@ config RTC_DRV_PCF85063
This driver can also be built as a module. If so, the module
will be called rtc-pcf85063.
+config RTC_DRV_PCF85363
+ tristate "NXP PCF85363"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ If you say yes here you get support for the PCF85363 RTC chip.
+
+ This driver can also be built as a module. If so, the module
+ will be called rtc-pcf85363.
+
+ The nvmem interface will be named pcf85363-#, where # is the
+ zero-based instance number.
+
config RTC_DRV_PCF8563
tristate "Philips PCF8563/Epson RTC8564"
help
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index 7230014..934a9dd 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -113,6 +113,7 @@ obj-$(CONFIG_RTC_DRV_PCF2123) += rtc-pcf2123.o
obj-$(CONFIG_RTC_DRV_PCF2127) += rtc-pcf2127.o
obj-$(CONFIG_RTC_DRV_PCF50633) += rtc-pcf50633.o
obj-$(CONFIG_RTC_DRV_PCF85063) += rtc-pcf85063.o
+obj-$(CONFIG_RTC_DRV_PCF85363) += rtc-pcf85363.o
obj-$(CONFIG_RTC_DRV_PCF8523) += rtc-pcf8523.o
obj-$(CONFIG_RTC_DRV_PCF8563) += rtc-pcf8563.o
obj-$(CONFIG_RTC_DRV_PCF8583) += rtc-pcf8583.o
diff --git a/drivers/rtc/rtc-pcf85363.c b/drivers/rtc/rtc-pcf85363.c
new file mode 100644
index 0000000..cf1e70c
--- /dev/null
+++ b/drivers/rtc/rtc-pcf85363.c
@@ -0,0 +1,221 @@
+/*
+ * drivers/rtc/rtc-pcf85363.c
+ *
+ * Driver for NXP PCF85363 real-time clock.
+ *
+ * Copyright (C) 2017 Eric Nelson
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Based loosely on rtc-8583 by Russell King, Wolfram Sang and Juergen Beisert
+ */
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/rtc.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/errno.h>
+#include <linux/bcd.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+
+/*
+ * Date/Time registers
+ */
+#define DT_100THS 0x00
+#define DT_SECS 0x01
+#define DT_MINUTES 0x02
+#define DT_HOURS 0x03
+#define DT_DAYS 0x04
+#define DT_WEEKDAYS 0x05
+#define DT_MONTHS 0x06
+#define DT_YEARS 0x07
+
+/*
+ * Alarm registers
+ */
+#define DT_SECOND_ALM1 0x08
+#define DT_MINUTE_ALM1 0x09
+#define DT_HOUR_ALM1 0x0a
+#define DT_DAY_ALM1 0x0b
+#define DT_MONTH_ALM1 0x0c
+#define DT_MINUTE_ALM2 0x0d
+#define DT_HOUR_ALM2 0x0e
+#define DT_WEEKDAY_ALM2 0x0f
+#define DT_ALARM_EN 0x10
+
+/*
+ * Time stamp registers
+ */
+#define DT_TIMESTAMP1 0x11
+#define DT_TIMESTAMP2 0x17
+#define DT_TIMESTAMP3 0x1d
+#define DT_TS_MODE 0x23
+
+/*
+ * control registers
+ */
+#define CTRL_OFFSET 0x24
+#define CTRL_OSCILLATOR 0x25
+#define CTRL_BATTERY 0x26
+#define CTRL_PIN_IO 0x27
+#define CTRL_FUNCTION 0x28
+#define CTRL_INTA_EN 0x29
+#define CTRL_INTB_EN 0x2a
+#define CTRL_FLAGS 0x2b
+#define CTRL_RAMBYTE 0x2c
+#define CTRL_WDOG 0x2d
+#define CTRL_STOP_EN 0x2e
+#define CTRL_RESETS 0x2f
+#define CTRL_RAM 0x40
+
+#define NVRAM_SIZE 0x40
+
+static struct i2c_driver pcf85363_driver;
+
+struct pcf85363 {
+ struct device *dev;
+ struct rtc_device *rtc;
+ struct nvmem_config nvmem_cfg;
+ struct regmap *regmap;
+};
+
+static int pcf85363_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+ struct pcf85363 *pcf85363 = dev_get_drvdata(dev);
+ unsigned char buf[DT_YEARS + 1];
+ int ret, len = sizeof(buf);
+
+ /* read the RTC date and time registers all at once */
+ ret = regmap_bulk_read(pcf85363->regmap, DT_100THS, buf, len);
+ if (ret) {
+ dev_err(dev, "%s: error %d\n", __func__, ret);
+ return ret;
+ }
+
+ tm->tm_year = bcd2bin(buf[DT_YEARS]);
+ /* adjust for 1900 base of rtc_time */
+ tm->tm_year += 100;
+
+ tm->tm_wday = buf[DT_WEEKDAYS] & 7;
+ buf[DT_SECS] &= 0x7F;
+ tm->tm_sec = bcd2bin(buf[DT_SECS]);
+ buf[DT_MINUTES] &= 0x7F;
+ tm->tm_min = bcd2bin(buf[DT_MINUTES]);
+ tm->tm_hour = bcd2bin(buf[DT_HOURS]);
+ tm->tm_mday = bcd2bin(buf[DT_DAYS]);
+ tm->tm_mon = bcd2bin(buf[DT_MONTHS]) - 1;
+
+ return 0;
+}
+
+static int pcf85363_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+ struct pcf85363 *pcf85363 = dev_get_drvdata(dev);
+ unsigned char buf[DT_YEARS + 1];
+ int len = sizeof(buf);
+
+ buf[DT_100THS] = 0;
+ buf[DT_SECS] = bin2bcd(tm->tm_sec);
+ buf[DT_MINUTES] = bin2bcd(tm->tm_min);
+ buf[DT_HOURS] = bin2bcd(tm->tm_hour);
+ buf[DT_DAYS] = bin2bcd(tm->tm_mday);
+ buf[DT_WEEKDAYS] = tm->tm_wday;
+ buf[DT_MONTHS] = bin2bcd(tm->tm_mon + 1);
+ buf[DT_YEARS] = bin2bcd(tm->tm_year % 100);
+
+ return regmap_bulk_write(pcf85363->regmap, DT_100THS,
+ buf, len);
+}
+
+static const struct rtc_class_ops rtc_ops = {
+ .read_time = pcf85363_rtc_read_time,
+ .set_time = pcf85363_rtc_set_time,
+};
+
+static int pcf85363_nvram_read(void *priv, unsigned int offset, void *val,
+ size_t bytes)
+{
+ struct pcf85363 *pcf85363 = priv;
+
+ return regmap_bulk_read(pcf85363->regmap, CTRL_RAM + offset,
+ val, bytes);
+}
+
+static int pcf85363_nvram_write(void *priv, unsigned int offset, void *val,
+ size_t bytes)
+{
+ struct pcf85363 *pcf85363 = priv;
+
+ return regmap_bulk_write(pcf85363->regmap, CTRL_RAM + offset,
+ val, bytes);
+}
+
+static const struct regmap_config regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+};
+
+static int pcf85363_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct pcf85363 *pcf85363;
+
+ if (!i2c_check_functionality(client->adapter, I2C_FUNC_I2C))
+ return -ENODEV;
+
+ pcf85363 = devm_kzalloc(&client->dev, sizeof(struct pcf85363),
+ GFP_KERNEL);
+ if (!pcf85363)
+ return -ENOMEM;
+
+ pcf85363->regmap = devm_regmap_init_i2c(client, ®map_config);
+ if (IS_ERR(pcf85363->regmap)) {
+ dev_err(&client->dev, "regmap allocation failed\n");
+ return PTR_ERR(pcf85363->regmap);
+ }
+
+ pcf85363->dev = &client->dev;
+ i2c_set_clientdata(client, pcf85363);
+
+ pcf85363->rtc = devm_rtc_allocate_device(pcf85363->dev);
+ if (IS_ERR(pcf85363->rtc))
+ return PTR_ERR(pcf85363->rtc);
+
+ pcf85363->nvmem_cfg.name = "pcf85363-";
+ pcf85363->nvmem_cfg.word_size = 1;
+ pcf85363->nvmem_cfg.stride = 1;
+ pcf85363->nvmem_cfg.size = NVRAM_SIZE;
+ pcf85363->nvmem_cfg.reg_read = pcf85363_nvram_read;
+ pcf85363->nvmem_cfg.reg_write = pcf85363_nvram_write;
+ pcf85363->nvmem_cfg.priv = pcf85363;
+ pcf85363->rtc->nvmem_config = &pcf85363->nvmem_cfg;
+ pcf85363->rtc->nvram_old_abi = true;
+ pcf85363->rtc->ops = &rtc_ops;
+
+ return rtc_register_device(pcf85363->rtc);
+}
+
+static const struct of_device_id dev_ids[] = {
+ { .compatible = "nxp,pcf85363" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, dev_ids);
+
+static struct i2c_driver pcf85363_driver = {
+ .driver = {
+ .name = "pcf85363",
+ .of_match_table = of_match_ptr(dev_ids),
+ },
+ .probe = pcf85363_probe,
+};
+
+module_i2c_driver(pcf85363_driver);
+
+MODULE_AUTHOR("Eric Nelson");
+MODULE_DESCRIPTION("pcf85363 I2C RTC driver");
+MODULE_LICENSE("GPL");
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-10-11 15:56 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-10-09 19:41 [PATCH] rtc: add support for NXP PCF85363 real-time clock Eric Nelson
[not found] ` <1507578100-2148-1-git-send-email-eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
2017-10-10 13:31 ` Fabio Estevam
[not found] ` <CAOMZO5C_boginn88C7zgXSBaikx==5FHJrgaE1ewYUyUgGfnFQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-10-11 15:08 ` Eric Nelson
2017-10-11 15:56 ` Eric Nelson [this message]
[not found] ` <1507737390-27818-1-git-send-email-eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
2017-10-12 21:55 ` [PATCH V2] " Fabio Estevam
2017-10-17 20:06 ` Rob Herring
2017-10-17 22:24 ` Eric Nelson
[not found] ` <20602538-2164-e85c-33b6-31c99dfa8a5e-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
2017-10-19 21:24 ` Rob Herring
[not found] ` <CAL_Jsq+QQK=NTMBwk=h0uszLW0uSiEd1fmF09USRNFM-2VgiSQ-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2017-11-01 15:01 ` [PATCH V3] " Eric Nelson
[not found] ` <1509548480-29472-1-git-send-email-eric-SeqgQ6RdavfQT0dZR+AlfA@public.gmane.org>
2017-11-01 17:45 ` Rob Herring
2017-11-04 16:08 ` Alexandre Belloni
[not found] ` <20171104160836.bah5su2ld5ckycr3-m++hUPXGwpdeoWH0uzbU5w@public.gmane.org>
2017-11-06 14:32 ` Eric Nelson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1507737390-27818-1-git-send-email-eric@nelint.com \
--to=eric-seqgq6rdavfqt0dzr+alfa@public.gmane.org \
--cc=a.zummo-BfzFCNDTiLLj+vYz1yj4TQ@public.gmane.org \
--cc=alexandre.belloni-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=festevam-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=linux-rtc-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=otavio.salvador-fKevB0iiKLMBZ+LybsDmbA@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).