[PATCH v2 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings

[PATCH v2 1/3] ARM: dts: imx6sx-sdb: Convert from fbdev to drm bindings

[Marco Franchi]

It is preferred to use the panel compatible string rather than passing
the LCD timing in the device tree.

So pass the "sii,43wvf1g" compatible string, which describes the parallel 
LCD.

Also pass the 'backlight' property as described in
Documentation/devicetree/bindings/display/panel/simple-panel.txt

Signed-off-by: Marco Franchi <marcofrk-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
---
Changes since v1:
-change subject
-change message log
-includes into a set of patches
-rebase to linux-next
-fix regulator name and properties
 arch/arm/boot/dts/imx6sx-sdb.dtsi | 48 +++++++++++++++++++--------------------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sx-sdb.dtsi b/arch/arm/boot/dts/imx6sx-sdb.dtsi
index d57a41c..d35aa85 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dtsi
+++ b/arch/arm/boot/dts/imx6sx-sdb.dtsi
@@ -24,7 +24,7 @@
 		reg = <0x80000000 0x40000000>;
 	};
 
-	backlight {
+	backlight_display: backlight-display {
 		compatible = "pwm-backlight";
 		pwms = <&pwm3 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -129,6 +129,13 @@
 		enable-active-high;
 	};
 
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
 	sound {
 		compatible = "fsl,imx6sx-sdb-wm8962", "fsl,imx-audio-wm8962";
 		model = "wm8962-audio";
@@ -144,6 +151,19 @@
 		mux-int-port = <2>;
 		mux-ext-port = <6>;
 	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
 };
 
 &audmux {
@@ -221,31 +241,11 @@
 &lcdif1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcd>;
-	lcd-supply = <&reg_lcd_3v3>;
-	display = <&display0>;
 	status = "okay";
 
-	display0: display0 {
-		bits-per-pixel = <16>;
-		bus-width = <24>;
-
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: timing0 {
-				clock-frequency = <33500000>;
-				hactive = <800>;
-				vactive = <480>;
-				hback-porch = <89>;
-				hfront-porch = <164>;
-				vback-porch = <23>;
-				vfront-porch = <10>;
-				hsync-len = <10>;
-				vsync-len = <10>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				de-active = <1>;
-				pixelclk-active = <0>;
-			};
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
 		};
 	};
 };
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 2/3] ARM: dts: imx6sl-evk: Rearrange the regulators node

[Marco Franchi]

It is not recommended to place regulators inside "simple-bus", so move 
them out.

The motivation for doing this is to make it easier to adding new 
regulators.

Signed-off-by: Marco Franchi <marcofrk@gmail.com>
---
 arch/arm/boot/dts/imx6sl-evk.dts | 85 +++++++++++++++++-----------------------
 1 file changed, 37 insertions(+), 48 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 60600b4..645a460 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -39,58 +39,47 @@
 		};
 	};
 
-	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		reg_usb_otg1_vbus: regulator@0 {
-			compatible = "regulator-fixed";
-			reg = <0>;
-			regulator-name = "usb_otg1_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio4 0 0>;
-			enable-active-high;
-			vin-supply = <&swbst_reg>;
-		};
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 0 0>;
+		enable-active-high;
+		vin-supply = <&swbst_reg>;
+	};
 
-		reg_usb_otg2_vbus: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "usb_otg2_vbus";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			gpio = <&gpio4 2 0>;
-			enable-active-high;
-			vin-supply = <&swbst_reg>;
-		};
+	reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 2 0>;
+		enable-active-high;
+		vin-supply = <&swbst_reg>;
+	};
 
-		reg_aud3v: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "wm8962-supply-3v15";
-			regulator-min-microvolt = <3150000>;
-			regulator-max-microvolt = <3150000>;
-			regulator-boot-on;
-		};
+	reg_aud3v: regulator-aud3v {
+		compatible = "regulator-fixed";
+		regulator-name = "wm8962-supply-3v15";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+		regulator-boot-on;
+	};
 
-		reg_aud4v: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "wm8962-supply-4v2";
-			regulator-min-microvolt = <4325000>;
-			regulator-max-microvolt = <4325000>;
-			regulator-boot-on;
-		};
+	reg_aud4v: regulator-aud4v {
+		compatible = "regulator-fixed";
+		regulator-name = "wm8962-supply-4v2";
+		regulator-min-microvolt = <4325000>;
+		regulator-max-microvolt = <4325000>;
+		regulator-boot-on;
+	};
 
-		reg_lcd_3v3: regulator@4 {
-			compatible = "regulator-fixed";
-			reg = <4>;
-			regulator-name = "lcd-3v3";
-			gpio = <&gpio4 3 0>;
-			enable-active-high;
-		};
+	reg_lcd_3v3: regulator-lcd-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-3v3";
+		gpio = <&gpio4 3 0>;
+		enable-active-high;
 	};
 
 	sound {
-- 
2.7.4

[PATCH v2 3/3] ARM: dts: imx6sl-evk: Convert from fbdev to drm bindings

[Marco Franchi]

It is preferred to use the panel compatible string rather than passing 
the LCD timing in the device tree.

So pass the "sii,43wvf1g" compatible string which describes the parallel 
LCD.

Also, pass the 'backlight' property as described in 
Documentation/devicetree/bindings/display/panel/simple-panel.txt

Signed-off-by: Marco Franchi <marco.franchi-3arQi8VN3Tc@public.gmane.org>
---
Changes since v1:
-change subject
-change message log
-includes into a set of patches
-fix regulator name and properties
 arch/arm/boot/dts/imx6sl-evk.dts | 48 ++++++++++++++++++++--------------------
 1 file changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 645a460..a395de4 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -20,7 +20,7 @@
 		reg = <0x80000000 0x40000000>;
 	};
 
-	backlight {
+	backlight_display: backlight_display {
 		compatible = "pwm-backlight";
 		pwms = <&pwm1 0 5000000>;
 		brightness-levels = <0 4 8 16 32 64 128 255>;
@@ -82,6 +82,13 @@
 		enable-active-high;
 	};
 
+	reg_lcd_5v: regulator-lcd-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
 	sound {
 		compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962";
 		model = "wm8962-audio";
@@ -97,6 +104,19 @@
 		mux-int-port = <2>;
 		mux-ext-port = <3>;
 	};
+
+	panel {
+		compatible = "sii,43wvf1g";
+		backlight = <&backlight_display>;
+		dvdd-supply = <&reg_lcd_3v3>;
+		avdd-supply = <&reg_lcd_5v>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
 };
 
 &audmux {
@@ -535,31 +555,11 @@
 &lcdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcd>;
-	lcd-supply = <&reg_lcd_3v3>;
-	display = <&display0>;
 	status = "okay";
 
-	display0: display0 {
-		bits-per-pixel = <32>;
-		bus-width = <24>;
-
-		display-timings {
-			native-mode = <&timing0>;
-			timing0: timing0 {
-				clock-frequency = <33500000>;
-				hactive = <800>;
-				vactive = <480>;
-				hback-porch = <89>;
-				hfront-porch = <164>;
-				vback-porch = <23>;
-				vfront-porch = <10>;
-				hsync-len = <10>;
-				vsync-len = <10>;
-				hsync-active = <0>;
-				vsync-active = <0>;
-				de-active = <1>;
-				pixelclk-active = <0>;
-			};
+	port {
+		display_out: endpoint {
+			remote-endpoint = <&panel_in>;
 		};
 	};
 };
-- 
2.7.4

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/3] ARM: dts: imx6sl-evk: Rearrange the regulators node

[Fabio Estevam]

Hi Marco,

You missed to pass the v2 notation for this patch in the Subject.

On Wed, Dec 6, 2017 at 12:53 AM, Marco Franchi <marcofrk-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org> wrote:

> +       reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
> +               compatible = "regulator-fixed";
> +               regulator-name = "usb_otg1_vbus";
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;
> +               gpio = <&gpio4 0 0>;

gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;

would easier to read.

> +       reg_usb_otg2_vbus: regulator-usb-otg2-vbus {
> +               compatible = "regulator-fixed";
> +               regulator-name = "usb_otg2_vbus";
> +               regulator-min-microvolt = <5000000>;
> +               regulator-max-microvolt = <5000000>;
> +               gpio = <&gpio4 2 0>;

Ditto.

> -               };
> +       reg_lcd_3v3: regulator-lcd-3v3 {
> +               compatible = "regulator-fixed";
> +               regulator-name = "lcd-3v3";
> +               gpio = <&gpio4 3 0>;

Ditto.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html