From: Tero Kristo <t-kristo-l0cyMroinI0@public.gmane.org>
To: tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org,
bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org
Cc: linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: [PATCH 15/20] ARM: dts: omap5: add clkctrl nodes
Date: Thu, 7 Dec 2017 10:46:48 +0200 [thread overview]
Message-ID: <1512636413-25243-16-git-send-email-t-kristo@ti.com> (raw)
In-Reply-To: <1512636413-25243-1-git-send-email-t-kristo-l0cyMroinI0@public.gmane.org>
Add clkctrl nodes for OMAP5 SoC. These are going to be acting as
replacement for part of the existing clock data and the existing
clkctrl hooks under hwmod data.
This patch also removes any obsolete clock nodes, and reroutes all users
for these to use the new clkctrl clocks instead.
Signed-off-by: Tero Kristo <t-kristo-l0cyMroinI0@public.gmane.org>
---
arch/arm/boot/dts/omap5.dtsi | 29 +-
arch/arm/boot/dts/omap54xx-clocks.dtsi | 623 +++++++++++----------------------
2 files changed, 221 insertions(+), 431 deletions(-)
diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi
index b0992b8..474750c 100644
--- a/arch/arm/boot/dts/omap5.dtsi
+++ b/arch/arm/boot/dts/omap5.dtsi
@@ -744,7 +744,7 @@
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "timer1";
ti,timer-alwon;
- clocks = <&timer1_gfclk_mux>;
+ clocks = <&wkupaon_clkctrl 0x20 24>;
clock-names = "fck";
};
@@ -905,7 +905,8 @@
compatible = "ti,omap-usb2";
reg = <0x4a084000 0x7c>;
syscon-phy-power = <&scm_conf 0x300>;
- clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
+ clocks = <&usb_phy_cm_clk32k>,
+ <&l3init_clkctrl 0xd0 8>;
clock-names = "wkupclk", "refclk";
#phy-cells = <0>;
};
@@ -919,7 +920,7 @@
syscon-phy-power = <&scm_conf 0x370>;
clocks = <&usb_phy_cm_clk32k>,
<&sys_clkin>,
- <&usb_otg_ss_refclk960m>;
+ <&l3init_clkctrl 0xd0 8>;
clock-names = "wkupclk",
"sysclk",
"refclk";
@@ -987,7 +988,8 @@
<0x4A096800 0x40>; /* pll_ctrl */
reg-names = "phy_rx", "phy_tx", "pll_ctrl";
syscon-phy-power = <&scm_conf 0x374>;
- clocks = <&sys_clkin>, <&sata_ref_clk>;
+ clocks = <&sys_clkin>,
+ <&l3init_clkctrl 0x68 8>;
clock-names = "sysclk", "refclk";
#phy-cells = <0>;
};
@@ -999,7 +1001,7 @@
interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
phys = <&sata_phy>;
phy-names = "sata-phy";
- clocks = <&sata_ref_clk>;
+ clocks = <&l3init_clkctrl 0x68 8>;
ti,hwmods = "sata";
ports-implemented = <0x1>;
};
@@ -1009,7 +1011,7 @@
reg = <0x58000000 0x80>;
status = "disabled";
ti,hwmods = "dss_core";
- clocks = <&dss_dss_clk>;
+ clocks = <&dss_clkctrl 0 8>;
clock-names = "fck";
#address-cells = <1>;
#size-cells = <1>;
@@ -1020,7 +1022,7 @@
reg = <0x58001000 0x1000>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
ti,hwmods = "dss_dispc";
- clocks = <&dss_dss_clk>;
+ clocks = <&dss_clkctrl 0 8>;
clock-names = "fck";
};
@@ -1029,7 +1031,7 @@
reg = <0x58002000 0x100>;
status = "disabled";
ti,hwmods = "dss_rfbi";
- clocks = <&dss_dss_clk>, <&l3_iclk_div>;
+ clocks = <&dss_clkctrl 0 8>, <&l3_iclk_div>;
clock-names = "fck", "ick";
};
@@ -1042,7 +1044,8 @@
interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi1";
- clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+ clocks = <&dss_clkctrl 0 8>,
+ <&dss_clkctrl 0 10>;
clock-names = "fck", "sys_clk";
};
@@ -1055,7 +1058,8 @@
interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_dsi2";
- clocks = <&dss_dss_clk>, <&dss_sys_clk>;
+ clocks = <&dss_clkctrl 0 8>,
+ <&dss_clkctrl 0 10>;
clock-names = "fck", "sys_clk";
};
@@ -1069,7 +1073,8 @@
interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
ti,hwmods = "dss_hdmi";
- clocks = <&dss_48mhz_clk>, <&dss_sys_clk>;
+ clocks = <&dss_clkctrl 0 9>,
+ <&dss_clkctrl 0 10>;
clock-names = "fck", "sys_clk";
dmas = <&sdma 76>;
dma-names = "audio_tx";
@@ -1143,7 +1148,7 @@
coefficients = <65 (-1791)>;
};
-/include/ "omap54xx-clocks.dtsi"
+#include "omap54xx-clocks.dtsi"
&gpu_thermal {
coefficients = <117 (-2992)>;
diff --git a/arch/arm/boot/dts/omap54xx-clocks.dtsi b/arch/arm/boot/dts/omap54xx-clocks.dtsi
index 5291934..9619a74 100644
--- a/arch/arm/boot/dts/omap54xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap54xx-clocks.dtsi
@@ -432,22 +432,6 @@
reg = <0x0528>;
};
- dmic_sync_mux_ck: dmic_sync_mux_ck@538 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
- ti,bit-shift = <26>;
- reg = <0x0538>;
- };
-
- dmic_gfclk: dmic_gfclk@538 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&dmic_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
- ti,bit-shift = <24>;
- reg = <0x0538>;
- };
-
mcasp_sync_mux_ck: mcasp_sync_mux_ck@540 {
#clock-cells = <0>;
compatible = "ti,mux-clock";
@@ -464,86 +448,6 @@
reg = <0x0540>;
};
- mcbsp1_sync_mux_ck: mcbsp1_sync_mux_ck@548 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
- ti,bit-shift = <26>;
- reg = <0x0548>;
- };
-
- mcbsp1_gfclk: mcbsp1_gfclk@548 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&mcbsp1_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
- ti,bit-shift = <24>;
- reg = <0x0548>;
- };
-
- mcbsp2_sync_mux_ck: mcbsp2_sync_mux_ck@550 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
- ti,bit-shift = <26>;
- reg = <0x0550>;
- };
-
- mcbsp2_gfclk: mcbsp2_gfclk@550 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&mcbsp2_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
- ti,bit-shift = <24>;
- reg = <0x0550>;
- };
-
- mcbsp3_sync_mux_ck: mcbsp3_sync_mux_ck@558 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
- ti,bit-shift = <26>;
- reg = <0x0558>;
- };
-
- mcbsp3_gfclk: mcbsp3_gfclk@558 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&mcbsp3_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
- ti,bit-shift = <24>;
- reg = <0x0558>;
- };
-
- timer5_gfclk_mux: timer5_gfclk_mux@568 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&dss_syc_gfclk_div>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x0568>;
- };
-
- timer6_gfclk_mux: timer6_gfclk_mux@570 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&dss_syc_gfclk_div>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x0570>;
- };
-
- timer7_gfclk_mux: timer7_gfclk_mux@578 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&dss_syc_gfclk_div>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x0578>;
- };
-
- timer8_gfclk_mux: timer8_gfclk_mux@580 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&dss_syc_gfclk_div>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x0580>;
- };
-
dummy_ck: dummy_ck {
#clock-cells = <0>;
compatible = "fixed-clock";
@@ -603,23 +507,8 @@
clock-mult = <1>;
clock-div = <1>;
};
-
- gpio1_dbclk: gpio1_dbclk@1938 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1938>;
- };
-
- timer1_gfclk_mux: timer1_gfclk_mux@1940 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1940>;
- };
};
+
&cm_core_clocks {
dpll_per_byp_mux: dpll_per_byp_mux@14c {
@@ -825,95 +714,6 @@
ti,dividers = <1>, <8>;
};
- dss_32khz_clk: dss_32khz_clk@1420 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <11>;
- reg = <0x1420>;
- };
-
- dss_48mhz_clk: dss_48mhz_clk@1420 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&func_48m_fclk>;
- ti,bit-shift = <9>;
- reg = <0x1420>;
- };
-
- dss_dss_clk: dss_dss_clk@1420 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dpll_per_h12x2_ck>;
- ti,bit-shift = <8>;
- reg = <0x1420>;
- ti,set-rate-parent;
- };
-
- dss_sys_clk: dss_sys_clk@1420 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dss_syc_gfclk_div>;
- ti,bit-shift = <10>;
- reg = <0x1420>;
- };
-
- gpio2_dbclk: gpio2_dbclk@1060 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1060>;
- };
-
- gpio3_dbclk: gpio3_dbclk@1068 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1068>;
- };
-
- gpio4_dbclk: gpio4_dbclk@1070 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1070>;
- };
-
- gpio5_dbclk: gpio5_dbclk@1078 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1078>;
- };
-
- gpio6_dbclk: gpio6_dbclk@1080 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1080>;
- };
-
- gpio7_dbclk: gpio7_dbclk@1110 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1110>;
- };
-
- gpio8_dbclk: gpio8_dbclk@1118 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1118>;
- };
-
iss_ctrlclk: iss_ctrlclk@1320 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
@@ -938,118 +738,6 @@
reg = <0x0f20>;
};
- mmc1_32khz_clk: mmc1_32khz_clk@1628 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_32k_ck>;
- ti,bit-shift = <8>;
- reg = <0x1628>;
- };
-
- sata_ref_clk: sata_ref_clk@1688 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&sys_clkin>;
- ti,bit-shift = <8>;
- reg = <0x1688>;
- };
-
- usb_host_hs_hsic480m_p1_clk: usb_host_hs_hsic480m_p1_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dpll_usb_m2_ck>;
- ti,bit-shift = <13>;
- reg = <0x1658>;
- };
-
- usb_host_hs_hsic480m_p2_clk: usb_host_hs_hsic480m_p2_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dpll_usb_m2_ck>;
- ti,bit-shift = <14>;
- reg = <0x1658>;
- };
-
- usb_host_hs_hsic480m_p3_clk: usb_host_hs_hsic480m_p3_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dpll_usb_m2_ck>;
- ti,bit-shift = <7>;
- reg = <0x1658>;
- };
-
- usb_host_hs_hsic60m_p1_clk: usb_host_hs_hsic60m_p1_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <11>;
- reg = <0x1658>;
- };
-
- usb_host_hs_hsic60m_p2_clk: usb_host_hs_hsic60m_p2_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <12>;
- reg = <0x1658>;
- };
-
- usb_host_hs_hsic60m_p3_clk: usb_host_hs_hsic60m_p3_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <6>;
- reg = <0x1658>;
- };
-
- utmi_p1_gfclk: utmi_p1_gfclk@1658 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&l3init_60m_fclk>, <&xclk60mhsp1_ck>;
- ti,bit-shift = <24>;
- reg = <0x1658>;
- };
-
- usb_host_hs_utmi_p1_clk: usb_host_hs_utmi_p1_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&utmi_p1_gfclk>;
- ti,bit-shift = <8>;
- reg = <0x1658>;
- };
-
- utmi_p2_gfclk: utmi_p2_gfclk@1658 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&l3init_60m_fclk>, <&xclk60mhsp2_ck>;
- ti,bit-shift = <25>;
- reg = <0x1658>;
- };
-
- usb_host_hs_utmi_p2_clk: usb_host_hs_utmi_p2_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&utmi_p2_gfclk>;
- ti,bit-shift = <9>;
- reg = <0x1658>;
- };
-
- usb_host_hs_utmi_p3_clk: usb_host_hs_utmi_p3_clk@1658 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <10>;
- reg = <0x1658>;
- };
-
- usb_otg_ss_refclk960m: usb_otg_ss_refclk960m@16f0 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&dpll_usb_clkdcoldo>;
- ti,bit-shift = <8>;
- reg = <0x16f0>;
- };
-
usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 {
#clock-cells = <0>;
compatible = "ti,gate-clock";
@@ -1058,30 +746,6 @@
reg = <0x0640>;
};
- usb_tll_hs_usb_ch0_clk: usb_tll_hs_usb_ch0_clk@1668 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <8>;
- reg = <0x1668>;
- };
-
- usb_tll_hs_usb_ch1_clk: usb_tll_hs_usb_ch1_clk@1668 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <9>;
- reg = <0x1668>;
- };
-
- usb_tll_hs_usb_ch2_clk: usb_tll_hs_usb_ch2_clk@1668 {
- #clock-cells = <0>;
- compatible = "ti,gate-clock";
- clocks = <&l3init_60m_fclk>;
- ti,bit-shift = <10>;
- reg = <0x1668>;
- };
-
fdif_fclk: fdif_fclk@1328 {
#clock-cells = <0>;
compatible = "ti,divider-clock";
@@ -1115,88 +779,6 @@
ti,max-div = <2>;
reg = <0x1638>;
};
-
- mmc1_fclk_mux: mmc1_fclk_mux@1628 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&func_128m_clk>, <&dpll_per_m2x2_ck>;
- ti,bit-shift = <24>;
- reg = <0x1628>;
- };
-
- mmc1_fclk: mmc1_fclk@1628 {
- #clock-cells = <0>;
- compatible = "ti,divider-clock";
- clocks = <&mmc1_fclk_mux>;
- ti,bit-shift = <25>;
- ti,max-div = <2>;
- reg = <0x1628>;
- };
-
- mmc2_fclk_mux: mmc2_fclk_mux@1630 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&func_128m_clk>, <&dpll_per_m2x2_ck>;
- ti,bit-shift = <24>;
- reg = <0x1630>;
- };
-
- mmc2_fclk: mmc2_fclk@1630 {
- #clock-cells = <0>;
- compatible = "ti,divider-clock";
- clocks = <&mmc2_fclk_mux>;
- ti,bit-shift = <25>;
- ti,max-div = <2>;
- reg = <0x1630>;
- };
-
- timer10_gfclk_mux: timer10_gfclk_mux@1028 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1028>;
- };
-
- timer11_gfclk_mux: timer11_gfclk_mux@1030 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1030>;
- };
-
- timer2_gfclk_mux: timer2_gfclk_mux@1038 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1038>;
- };
-
- timer3_gfclk_mux: timer3_gfclk_mux@1040 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1040>;
- };
-
- timer4_gfclk_mux: timer4_gfclk_mux@1048 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1048>;
- };
-
- timer9_gfclk_mux: timer9_gfclk_mux@1050 {
- #clock-cells = <0>;
- compatible = "ti,mux-clock";
- clocks = <&sys_clkin>, <&sys_32k_ck>;
- ti,bit-shift = <24>;
- reg = <0x1050>;
- };
};
&cm_core_clockdomains {
@@ -1394,3 +976,206 @@
reg = <0x021c>;
};
};
+
+&cm_core_aon {
+ mpu_cm: mpu_cm@300 {
+ compatible = "ti,omap4-cm";
+ reg = <0x300 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x300 0x100>;
+
+ mpu_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ dsp_cm: dsp_cm@400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x400 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x400 0x100>;
+
+ dsp_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ abe_cm: abe_cm@500 {
+ compatible = "ti,omap4-cm";
+ reg = <0x500 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x500 0x100>;
+
+ abe_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x64>;
+ #clock-cells = <2>;
+ };
+ };
+
+};
+
+&cm_core {
+ l3main1_cm: l3main1_cm@700 {
+ compatible = "ti,omap4-cm";
+ reg = <0x700 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x700 0x100>;
+
+ l3main1_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3main2_cm: l3main2_cm@800 {
+ compatible = "ti,omap4-cm";
+ reg = <0x800 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x800 0x100>;
+
+ l3main2_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ ipu_cm: ipu_cm@900 {
+ compatible = "ti,omap4-cm";
+ reg = <0x900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x900 0x100>;
+
+ ipu_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ dma_cm: dma_cm@a00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xa00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xa00 0x100>;
+
+ dma_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ emif_cm: emif_cm@b00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xb00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xb00 0x100>;
+
+ emif_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x1c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4cfg_cm: l4cfg_cm@d00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xd00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xd00 0x100>;
+
+ l4cfg_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x14>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3instr_cm: l3instr_cm@e00 {
+ compatible = "ti,omap4-cm";
+ reg = <0xe00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0xe00 0x100>;
+
+ l3instr_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xc>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l4per_cm: l4per_cm@1000 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1000 0x200>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1000 0x200>;
+
+ l4per_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x15c>;
+ #clock-cells = <2>;
+ };
+ };
+
+ dss_cm: dss_cm@1400 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1400 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1400 0x100>;
+
+ dss_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x4>;
+ #clock-cells = <2>;
+ };
+ };
+
+ l3init_cm: l3init_cm@1600 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1600 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1600 0x100>;
+
+ l3init_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0xd4>;
+ #clock-cells = <2>;
+ };
+ };
+};
+
+&prm {
+ wkupaon_cm: wkupaon_cm@1900 {
+ compatible = "ti,omap4-cm";
+ reg = <0x1900 0x100>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x1900 0x100>;
+
+ wkupaon_clkctrl: clk@20 {
+ compatible = "ti,clkctrl";
+ reg = <0x20 0x5c>;
+ #clock-cells = <2>;
+ };
+ };
+};
--
1.9.1
--
Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki. Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2017-12-07 8:46 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-07 8:46 [PATCH 00/20] ARM: dts: add omap clkctrl support Tero Kristo
[not found] ` <1512636413-25243-1-git-send-email-t-kristo-l0cyMroinI0@public.gmane.org>
2017-12-07 8:46 ` [PATCH 01/20] ARM: dts: omap5: add fck under timer1 Tero Kristo
2017-12-07 8:46 ` [PATCH 02/20] ARM: dts: omap4: " Tero Kristo
2017-12-07 8:46 ` [PATCH 03/20] ARM: dts: am33xx: add fck under timers1/2 Tero Kristo
2017-12-07 8:46 ` [PATCH 04/20] ARM: dts: am43xx: " Tero Kristo
2017-12-07 8:46 ` [PATCH 05/20] ARM: dts: dra7: add fck under timer1 Tero Kristo
2017-12-07 8:46 ` [PATCH 06/20] ARM: dts: dm814x: add fck under timers1/2 Tero Kristo
2017-12-07 8:46 ` [PATCH 07/20] ARM: dts: dm816x: " Tero Kristo
2017-12-07 8:46 ` [PATCH 08/20] ARM: dts: omap5: add bus functionality to base PRCM nodes Tero Kristo
2017-12-07 8:46 ` [PATCH 09/20] ARM: dts: omap4: " Tero Kristo
2017-12-07 8:46 ` [PATCH 10/20] ARM: dts: dra7: " Tero Kristo
2017-12-07 8:46 ` [PATCH 11/20] ARM: dts: am33xx: add bus functionality to base PRCM node Tero Kristo
2017-12-07 8:46 ` [PATCH 12/20] ARM: dts: am43xx: " Tero Kristo
2017-12-07 8:46 ` [PATCH 13/20] ARM: dts: dm816x: " Tero Kristo
2017-12-07 8:46 ` [PATCH 14/20] ARM: dts: omap4: add clkctrl nodes Tero Kristo
[not found] ` <1512636413-25243-15-git-send-email-t-kristo-l0cyMroinI0@public.gmane.org>
2017-12-07 21:14 ` Tony Lindgren
2017-12-07 8:46 ` Tero Kristo [this message]
2017-12-07 8:46 ` [PATCH 16/20] ARM: dts: dra7: " Tero Kristo
2017-12-07 8:46 ` [PATCH 17/20] ARM: dts: am33xx: " Tero Kristo
2017-12-07 8:46 ` [PATCH 18/20] ARM: dts: am43xx: " Tero Kristo
2017-12-07 8:46 ` [PATCH 19/20] ARM: dts: dm814x: " Tero Kristo
2017-12-07 8:46 ` [PATCH 20/20] ARM: dts: dm816x: " Tero Kristo
2017-12-07 21:16 ` [PATCH 00/20] ARM: dts: add omap clkctrl support Tony Lindgren
[not found] ` <20171207211620.GD28152-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
2017-12-08 6:58 ` Tero Kristo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1512636413-25243-16-git-send-email-t-kristo@ti.com \
--to=t-kristo-l0cymroini0@public.gmane.org \
--cc=bcousson-rdvid1DuHRBWk0Htik3J/w@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).