From: Stefan Riedmueller <s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
To: shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org,
fabio.estevam-3arQi8VN3Tc@public.gmane.org
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
Stefan Riedmueller
<s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
Subject: [PATCH v3 0/6] ARM: dts: Add PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira carrier board support
Date: Fri, 22 Dec 2017 11:59:07 +0100 [thread overview]
Message-ID: <1513940353-6145-1-git-send-email-s.riedmueller@phytec.de> (raw)
This patchset adds support for the PHYTEC phyCORE-i.MX 6 and phyBOARD-Mira.
Following boards are included:
phyBOARD-Mira with phyCORE-i.MX 6 Quad/Dual with:
- i.MX 6Quad/Dual SOC
- NAND or eMMC
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
phyBAORD-Mira with phyCORE-i.MX 6 DualLight/Solo with:
- i.MX 6DualLight/Solo
- NAND
- HDMI interface
- 100 MBit/s Ethernet
- USB Host
- RS232
phyBOARD-Mira with phyCORE-i.MX 6 QuadPlus with:
- i.MX 6QuadPlus SOC
- NAND
- HDMI interface
- LVDS display interface
- Gigabit Ethernet
- USB Host
- CAN
- RS232
- PCIe
This board also contains an LVDS camera interface and parallel display
interface which are not yet supported.
The entire series is based on v4.15-rc4.
Changes since v1:
- Removed unnecessary ipu aliases
- Added unit-address to memory node name
- Fixed eeprom compatible to correct vendor name (atmel instead of cat)
- Fixed rtc compatible to correct vendor name (microcrystal instead of mc)
- Changed pcie regulator to be used with vpcie-supply in &pcie node and
removed regulator-always-on
- Changed pcie reset-gpio polarity to GPIO_ACTIVE_LOW
- Replaced fsl,uart-has-rtscts by uart-has-rtscts
- Fixed typos in defconfig patch
Changes since v2:
- Fixed typo in patch subject PATCH 4/6
- Added reviewed by tags on PATCH 4/6 and PATCH 6/6
Christian Hemp (2):
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK
ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo
RDK
Enrico Scholz (1):
ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus
Stefan Riedmueller (3):
ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM
ARM: dts: imx6: Add initial support for phyBOARD-Mira
ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts | 64 ++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts | 72 ++++
arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts | 72 ++++
arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi | 390 ++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++
arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts | 72 ++++
arch/arm/configs/imx_v6_v7_defconfig | 4 +
8 files changed, 960 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
create mode 100644 arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-mira.dtsi
create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
create mode 100644 arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
--
2.7.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next reply other threads:[~2017-12-22 10:59 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-12-22 10:59 Stefan Riedmueller [this message]
[not found] ` <1513940353-6145-1-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-22 10:59 ` [PATCH v3 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM Stefan Riedmueller
[not found] ` <1513940353-6145-2-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-22 18:26 ` Fabio Estevam
2017-12-27 2:18 ` Shawn Guo
2018-01-03 9:31 ` Stefan Riedmüller
2017-12-22 10:59 ` [PATCH v3 2/6] ARM: dts: imx6: Add initial support for phyBOARD-Mira Stefan Riedmueller
[not found] ` <1513940353-6145-3-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-22 18:30 ` Fabio Estevam
2017-12-27 2:29 ` Shawn Guo
2017-12-22 10:59 ` [PATCH v3 3/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6Quad/Dual RDK Stefan Riedmueller
[not found] ` <1513940353-6145-4-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-22 18:31 ` Fabio Estevam
2017-12-22 10:59 ` [PATCH v3 4/6] ARM: dts: imx6: Add support for phyBOARD-Mira i.MX 6 DualLight/Solo RDK Stefan Riedmueller
2017-12-22 10:59 ` [PATCH v3 5/6] ARM: dts: imx6: Add support for phyBOARD-Mira with i.MX 6QuadPlus Stefan Riedmueller
[not found] ` <1513940353-6145-6-git-send-email-s.riedmueller-guT5V/WYfQezQB+pC5nmwQ@public.gmane.org>
2017-12-22 18:32 ` Fabio Estevam
2017-12-22 10:59 ` [PATCH v3 6/6] ARM: imx_v6_v7_defconfig: Enable Dialog Semiconductor DA9062 driver Stefan Riedmueller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1513940353-6145-1-git-send-email-s.riedmueller@phytec.de \
--to=s.riedmueller-gut5v/wyfqezqb+pc5nmwq@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=fabio.estevam-3arQi8VN3Tc@public.gmane.org \
--cc=kernel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox