From: Yogesh Gaur <yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
To: linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
mark.rutland-5wv7dgnIgG8@public.gmane.org,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org,
cyrille.pitchen-yU5RGvR974pGWvitb5QawA@public.gmane.org,
computersforpeace-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org,
han.xu-3arQi8VN3Tc@public.gmane.org,
festevam-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org,
prabhakar.kushwaha-3arQi8VN3Tc@public.gmane.org,
suresh.gupta-3arQi8VN3Tc@public.gmane.org,
Yogesh Gaur <yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
Subject: [PATCH 1/2] mtd: fsl-quadspi: Update slave device hwcap based on mode provided in dtsi file
Date: Tue, 30 Jan 2018 23:01:07 +0530 [thread overview]
Message-ID: <1517333468-17153-2-git-send-email-yogeshnarayan.gaur@nxp.com> (raw)
In-Reply-To: <1517333468-17153-1-git-send-email-yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
FSL QuadSPI controller supports Single, dual, quad modes of operation.
Mode information is available via "spi-tx-bus-width" and
"spi-rx-bus-width" nodes of device tree for the connected slave device.
Update read and write hwcap capability for slave device by reading
"spi-rx-bus-width" and "spi-tx-bus-width" respectively.
Assign hwcaps mask to minimal caps for the slave node i.e.
SNOR_HWCAPS_READ | SNOR_HWCAPS_PP
If value not provided in device tree file, then fallback to default
mode i.e. SNOR_HWCAPS_READ_1_1_4 and SNOR_HWCAPS_PP.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha-3arQi8VN3Tc@public.gmane.org>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
---
drivers/mtd/spi-nor/fsl-quadspi.c | 56 +++++++++++++++++++++++++++++++++++----
1 file changed, 51 insertions(+), 5 deletions(-)
diff --git a/drivers/mtd/spi-nor/fsl-quadspi.c b/drivers/mtd/spi-nor/fsl-quadspi.c
index b9c5918..1503e0c 100644
--- a/drivers/mtd/spi-nor/fsl-quadspi.c
+++ b/drivers/mtd/spi-nor/fsl-quadspi.c
@@ -994,17 +994,14 @@ static void fsl_qspi_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
static int fsl_qspi_probe(struct platform_device *pdev)
{
- const struct spi_nor_hwcaps hwcaps = {
- .mask = SNOR_HWCAPS_READ_1_1_4 |
- SNOR_HWCAPS_PP,
- };
+ struct spi_nor_hwcaps hwcaps;
struct device_node *np = pdev->dev.of_node;
struct device *dev = &pdev->dev;
struct fsl_qspi *q;
struct resource *res;
struct spi_nor *nor;
struct mtd_info *mtd;
- int ret, i = 0;
+ int ret, i = 0, value;
q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL);
if (!q)
@@ -1077,6 +1074,10 @@ static int fsl_qspi_probe(struct platform_device *pdev)
/* iterate the subnodes. */
for_each_available_child_of_node(dev->of_node, np) {
+ /* Reset hwcaps mask to minimal caps for the slave node. */
+ hwcaps.mask = SNOR_HWCAPS_READ | SNOR_HWCAPS_PP;
+ value = 0;
+
/* skip the holes */
if (!q->has_second_chip)
i *= 2;
@@ -1106,6 +1107,51 @@ static int fsl_qspi_probe(struct platform_device *pdev)
/* set the chip address for READID */
fsl_qspi_set_base_addr(q, nor);
+ /*
+ * If spi-rx-bus-width and spi-tx-bus-width not defined assign
+ * default hardware capabilities SNOR_HWCAPS_READ_1_1_4 and
+ * SNOR_HWCAPS_PP supported by the Quad-SPI controller.
+ */
+ if (!of_property_read_u32(np, "spi-rx-bus-width", &value)) {
+ switch (value) {
+ case 1:
+ hwcaps.mask |= SNOR_HWCAPS_READ |
+ SNOR_HWCAPS_READ_FAST;
+ break;
+ case 2:
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_2 |
+ SNOR_HWCAPS_READ_1_2_2;
+ break;
+ case 4:
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4 |
+ SNOR_HWCAPS_READ_1_4_4;
+ break;
+ default:
+ dev_err(dev,
+ "spi-rx-bus-width %d not supported\n",
+ value);
+ break;
+ }
+ } else
+ hwcaps.mask |= SNOR_HWCAPS_READ_1_1_4;
+
+ if (!of_property_read_u32(np, "spi-tx-bus-width", &value)) {
+ switch (value) {
+ case 1:
+ hwcaps.mask |= SNOR_HWCAPS_PP;
+ break;
+ case 4:
+ hwcaps.mask |= SNOR_HWCAPS_PP_1_1_4 |
+ SNOR_HWCAPS_PP_1_4_4;
+ break;
+ default:
+ dev_err(dev,
+ "spi-tx-bus-width %d not supported\n",
+ value);
+ break;
+ }
+ }
+
ret = spi_nor_scan(nor, NULL, &hwcaps);
if (ret)
goto mutex_failed;
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2018-01-30 17:31 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-30 17:31 [PATCH 0/2] mtd: fsl-quadspi: Update slave device hwcap based on mode provided in dtsi file Yogesh Gaur
[not found] ` <1517333468-17153-1-git-send-email-yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
2018-01-30 17:31 ` Yogesh Gaur [this message]
2018-01-30 17:31 ` [PATCH 2/2] dt-bindings: fsl-quadspi: spi-rx/tx-bus-width usage example Yogesh Gaur
-- strict thread matches above, loose matches on Subject: below --
2018-01-30 17:33 [PATCH 0/2] mtd: fsl-quadspi: Update slave device hwcap based on mode provided in dtsi file Yogesh Gaur
[not found] ` <1517333637-17331-1-git-send-email-yogeshnarayan.gaur-3arQi8VN3Tc@public.gmane.org>
2018-01-30 17:33 ` [PATCH 1/2] " Yogesh Gaur
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1517333468-17153-2-git-send-email-yogeshnarayan.gaur@nxp.com \
--to=yogeshnarayan.gaur-3arqi8vn3tc@public.gmane.org \
--cc=boris.brezillon-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org \
--cc=computersforpeace-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=cyrille.pitchen-yU5RGvR974pGWvitb5QawA@public.gmane.org \
--cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
--cc=festevam-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org \
--cc=han.xu-3arQi8VN3Tc@public.gmane.org \
--cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=linux-mtd-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
--cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
--cc=prabhakar.kushwaha-3arQi8VN3Tc@public.gmane.org \
--cc=robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=shawnguo-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
--cc=suresh.gupta-3arQi8VN3Tc@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).