From: Manu Gautam <mgautam@codeaurora.org>
To: Kishon Vijay Abraham I <kishon@ti.com>,
robh@kernel.org, sboyd@kernel.org
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
dianders@chromium.org, evgreen@chromium.org,
Vivek Gautam <vivek.gautam@codeaurora.org>,
linux-arm-msm@vger.kernel.org, linux-usb@vger.kernel.org,
Manu Gautam <mgautam@codeaurora.org>
Subject: [PATCH v5 0/7] phy: qcom: Updates for USB PHYs on SDM845
Date: Thu, 3 May 2018 02:36:07 +0530 [thread overview]
Message-ID: <1525295174-15995-1-git-send-email-mgautam@codeaurora.org> (raw)
SDM845 has two USB instances each with QUSB2 and QMP PHYs.
One of the QMP PHY is USB-DP (DisplayPort) combo PHY where
as other one is single lane UNI-PHY (without DP support).
Changes are related to PHY configuration for electrical
parameters tuning to improve eye-diagram and some fixes.
First gcc-msm8996 driver patch is dependent on following
patch which is now applied by Stephen.
https://patchwork.kernel.org/patch/10375043/
Changes since v4:
- Addressed Doug's review comments to have QUSB2 PHY tuning
values in header file.
- Updated msm8996-gcc patch to use BRANCH_HALT_SKIP flag
added by patch - https://patchwork.kernel.org/patch/10375041/
Changes since v3:
- As per Doug's review comments added device tree parameters
to handle board level differences in PHY tuning values instead
of adding separate device tree bindings.
- Replace PHY version specific bindings names with SOC name as
no one is going to use generic binding names.
- Update halt_check to not check for pipe clock status that
allows to simplify pipe_clk handling in QMP driver.
Changes since v2:
- Use separate phy_ops for USB to not register power_on op.
- And other minor changes as per review comments from Stephen.
Changes since v1:
- Updated qusb2 compatibility name as per comment from Vivek.
Manu Gautam (7):
clk: msm8996-gcc: Mark halt check as no-op for USB/PCIE pipe_clk
phy: qcom-qmp: Enable pipe_clk before PHY initialization
phy: qcom-qusb2: Fix crash if nvmem cell not specified
dt-bindings: phy-qcom-qmp: Update bindings for sdm845
phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support for sdm845
dt-bindings: phy-qcom-usb2: Add support to override tuning values
phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845
.../devicetree/bindings/phy/qcom-qmp-phy.txt | 3 +-
.../devicetree/bindings/phy/qcom-qusb2-phy.txt | 23 ++-
drivers/clk/qcom/gcc-msm8996.c | 4 +
drivers/phy/qualcomm/phy-qcom-qmp.c | 169 +++++++++++++++++++--
drivers/phy/qualcomm/phy-qcom-qmp.h | 5 +
drivers/phy/qualcomm/phy-qcom-qusb2.c | 130 +++++++++++++++-
include/dt-bindings/phy/phy-qcom-qusb2.h | 37 +++++
7 files changed, 346 insertions(+), 25 deletions(-)
create mode 100644 include/dt-bindings/phy/phy-qcom-qusb2.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
next reply other threads:[~2018-05-02 21:06 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-02 21:06 Manu Gautam [this message]
2018-05-02 21:06 ` [PATCH v5 1/7] clk: msm8996-gcc: Mark halt check as no-op for USB/PCIE pipe_clk Manu Gautam
2018-05-03 10:41 ` kbuild test robot
2018-05-04 19:46 ` Doug Anderson
2018-06-01 18:45 ` Stephen Boyd
2018-05-02 21:06 ` [PATCH v5 2/7] phy: qcom-qmp: Enable pipe_clk before PHY initialization Manu Gautam
2018-05-04 19:47 ` Doug Anderson
2018-05-02 21:06 ` [PATCH v5 3/7] phy: qcom-qusb2: Fix crash if nvmem cell not specified Manu Gautam
2018-05-02 21:06 ` [PATCH v5 4/7] dt-bindings: phy-qcom-qmp: Update bindings for sdm845 Manu Gautam
2018-05-07 14:08 ` Rob Herring
2018-05-02 21:06 ` [PATCH v5 5/7] phy: qcom-qmp: Add QMP V3 USB3 UNI PHY support " Manu Gautam
2018-05-02 21:06 ` [PATCH v5 6/7] dt-bindings: phy-qcom-usb2: Add support to override tuning values Manu Gautam
2018-05-04 19:47 ` Doug Anderson
2018-05-07 15:53 ` Rob Herring
2018-05-07 15:57 ` Doug Anderson
2018-05-07 20:40 ` Rob Herring
2018-05-02 21:06 ` [PATCH v5 7/7] phy: qcom-qusb2: Add QUSB2 PHYs support for sdm845 Manu Gautam
2018-05-04 19:47 ` Doug Anderson
-- strict thread matches above, loose matches on Subject: below --
2018-05-02 21:00 [PATCH v5 0/7] phy: qcom: Updates for USB PHYs on SDM845 Manu Gautam
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1525295174-15995-1-git-send-email-mgautam@codeaurora.org \
--to=mgautam@codeaurora.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=evgreen@chromium.org \
--cc=kishon@ti.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=vivek.gautam@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).