[PATCH v0 0/2] Add sdmmc UHS support to ROC-RK3328-CC board

[PATCH v0 0/2] Add sdmmc UHS support to ROC-RK3328-CC board

[djw]

From: Levin Du <djw@t-chip.com.cn>

Hi all,

This is an attemp to add sdmmc UHS support to the ROC-RK3328-CC board.

It adds a new compatible `rockchip,rk3328-gpio-syscon10` to the gpio-syscon
driver,  so that a new gpio controller named `gpio_syscon10` can be defined
and used in the regulator-gpio. This regulator controls the signal voltage of the
sdmmc. It is essential for UHS support which requires 1.8V signal voltage.


Levin Du (2):
  gpio: syscon: Add gpio-syscon for rk3328
  arm64: dts: rockchip: Add sdmmc UHS support for roc-rk3328-cc

 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts | 36 ++++++++++++++++++++++++++
 drivers/gpio/gpio-syscon.c                     | 32 +++++++++++++++++++++++
 2 files changed, 68 insertions(+)

-- 
2.7.4

[PATCH v0 2/2] arm64: dts: rockchip: Add sdmmc UHS support for roc-rk3328-cc

[djw]

From: Levin Du <djw@t-chip.com.cn>

In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by
the vcc_sdio regulator, which is a mux between 1.8V and 3.3V,
controlled by a special output only gpio pin.

However, this pin,  not being a normal gpio in the rockchip pinctrl,
is set by bit 1 of system register GRF_SOC_CON10. Therefore a new
gpio controller using gpio-syscon driver is defined in order to use
regulator-gpio.

If the signal voltage changes, the io domain needs to change
correspondingly.

To use this feature, the following options are required in kernel config:
 - CONFIG_GPIO_SYSCON=y
 - CONFIG_POWER_AVS=y
 - CONFIG_ROCKCHIP_IODOMAIN=y

Signed-off-by: Levin Du <djw@t-chip.com.cn>

---

 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts | 36 ++++++++++++++++++++++++++
 1 file changed, 36 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
index 246c317..792cb04 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -14,6 +14,12 @@
 		stdout-path = "serial2:1500000n8";
 	};
 
+	gpio_syscon10: gpio-syscon10 {
+		compatible = "rockchip,rk3328-gpio-syscon10";
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
 	gmac_clkin: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -41,6 +47,19 @@
 		vin-supply = <&vcc_io>;
 	};
 
+	vcc_sdio: sdmmcio-regulator {
+		compatible = "regulator-gpio";
+		gpios = <&gpio_syscon10 1 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		regulator-name = "vcc_sdio";
+		regulator-type = "voltage";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+	};
+
 	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -208,6 +227,18 @@
 	};
 };
 
+&io_domains {
+	status = "okay";
+
+	vccio1-supply = <&vcc_io>;
+	vccio2-supply = <&vcc18_emmc>;
+	vccio3-supply = <&vcc_sdio>;
+	vccio4-supply = <&vcc_18>;
+	vccio5-supply = <&vcc_io>;
+	vccio6-supply = <&vcc_io>;
+	pmuio-supply = <&vcc_io>;
+};
+
 &pinctrl {
 	pmic {
 		pmic_int_l: pmic-int-l {
@@ -227,10 +258,15 @@
 	cap-mmc-highspeed;
 	cap-sd-highspeed;
 	disable-wp;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
 	max-frequency = <150000000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
 	vmmc-supply = <&vcc_sd>;
+	vqmmc-supply = <&vcc_sdio>;
 	status = "okay";
 };
 
-- 
2.7.4

Re: [PATCH v0 2/2] arm64: dts: rockchip: Add sdmmc UHS support for roc-rk3328-cc

[Heiko Stuebner]

Hi Levin,

Am Dienstag, 8. Mai 2018, 04:48:24 CEST schrieb djw@t-chip.com.cn:
> From: Levin Du <djw@t-chip.com.cn>
> 
> In roc-rk3328-cc board, the signal voltage of sdmmc is supplied by
> the vcc_sdio regulator, which is a mux between 1.8V and 3.3V,
> controlled by a special output only gpio pin.
> 
> However, this pin,  not being a normal gpio in the rockchip pinctrl,
> is set by bit 1 of system register GRF_SOC_CON10. Therefore a new
> gpio controller using gpio-syscon driver is defined in order to use
> regulator-gpio.
> 
> If the signal voltage changes, the io domain needs to change
> correspondingly.
> 
> To use this feature, the following options are required in kernel config:
>  - CONFIG_GPIO_SYSCON=y
>  - CONFIG_POWER_AVS=y
>  - CONFIG_ROCKCHIP_IODOMAIN=y
> 
> Signed-off-by: Levin Du <djw@t-chip.com.cn>
> 
> ---
> 
>  arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts | 36 ++++++++++++++++++++++++++
>  1 file changed, 36 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
> index 246c317..792cb04 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
> +++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
> @@ -14,6 +14,12 @@
>  		stdout-path = "serial2:1500000n8";
>  	};
>  
> +	gpio_syscon10: gpio-syscon10 {
> +		compatible = "rockchip,rk3328-gpio-syscon10";
> +		gpio-controller;
> +		#gpio-cells = <2>;
> +	};
> +

please split this into a separate patch, move it to rk3328.dtsi and together
with the suggestions from patch 1/2 make it look like

grf: syscon@ff100000 {
	compatible = "rockchip,rk3328-grf", "syscon", "simple-mfd";
	reg = <0x0 0xff100000 0x0 0x1000>;
...
		gpio_mute: gpio-mute {
		compatible = "rockchip,rk3328-gpio-mute";
		gpio-controller;
		#gpio-cells = <2>;
	};
...
};

So making the gpio-controller a child of the grf node.
And as this definition is not specific to the roc-cc it should be in the
main devicetree file for the rk3328.

>  	gmac_clkin: external-gmac-clock {
>  		compatible = "fixed-clock";
>  		clock-frequency = <125000000>;
> @@ -41,6 +47,19 @@
>  		vin-supply = <&vcc_io>;
>  	};
>  
> +	vcc_sdio: sdmmcio-regulator {
> +		compatible = "regulator-gpio";
> +		gpios = <&gpio_syscon10 1 GPIO_ACTIVE_HIGH>;
> +		states = <1800000 0x1
> +			  3300000 0x0>;
> +		regulator-name = "vcc_sdio";
> +		regulator-type = "voltage";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		vin-supply = <&vcc_sys>;
> +	};
> +
>  	vcc_host1_5v: vcc_otg_5v: vcc-host1-5v-regulator {
>  		compatible = "regulator-fixed";
>  		enable-active-high;
> @@ -208,6 +227,18 @@
>  	};
>  };
>  
> +&io_domains {
> +	status = "okay";
> +
> +	vccio1-supply = <&vcc_io>;
> +	vccio2-supply = <&vcc18_emmc>;
> +	vccio3-supply = <&vcc_sdio>;
> +	vccio4-supply = <&vcc_18>;
> +	vccio5-supply = <&vcc_io>;
> +	vccio6-supply = <&vcc_io>;
> +	pmuio-supply = <&vcc_io>;
> +};
> +

Please split this into a separate patch about
"adding io-domain supplies for roc-cc"


>  &pinctrl {
>  	pmic {
>  		pmic_int_l: pmic-int-l {
> @@ -227,10 +258,15 @@
>  	cap-mmc-highspeed;
>  	cap-sd-highspeed;
>  	disable-wp;
> +	sd-uhs-sdr12;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr104;

please sort properties alphabetically, so between pinctrl-0 and vmmc-supply


>  	max-frequency = <150000000>;
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&sdmmc0_clk &sdmmc0_cmd &sdmmc0_dectn &sdmmc0_bus4>;
>  	vmmc-supply = <&vcc_sd>;
> +	vqmmc-supply = <&vcc_sdio>;
>  	status = "okay";
>  };


Thanks
Heiko