[PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe support for poplar board

[PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe support for poplar board

[Shawn Guo]

It adds combophy devices under peripheral controller and enables PCIe
support for Hi3798CV200 Poplar board.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
 .../boot/dts/hisilicon/hi3798cv200-poplar.dts      | 15 ++++++
 arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi     | 63 ++++++++++++++++++++++
 2 files changed, 78 insertions(+)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
index 4d5d644abb12..c4382e1f3c92 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
@@ -61,6 +61,15 @@
 			default-state = "off";
 		};
 	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3_PCIE0";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio6 7 0>;
+		enable-active-high;
+	};
 };
 
 &gmac1 {
@@ -146,6 +155,12 @@
 	status = "okay";
 };
 
+&pcie {
+	reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+	vpcie-supply = <&reg_pcie>;
+	status = "okay";
+};
+
 &sd0 {
 	bus-width = <4>;
 	cap-sd-highspeed;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
index 962bd79139e4..5b73403551e6 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -8,7 +8,9 @@
  */
 
 #include <dt-bindings/clock/histb-clock.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
 #include <dt-bindings/reset/ti-syscon.h>
 
 / {
@@ -106,6 +108,37 @@
 			#reset-cells = <2>;
 		};
 
+		perictrl: peripheral-controller@8a20000 {
+			compatible = "hisilicon,hi3798cv200-perictrl", "syscon",
+				     "simple-mfd";
+			reg = <0x8a20000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x8a20000 0x1000>;
+
+			combphy0: phy@850 {
+				compatible = "hisilicon,hi3798cv200-combphy";
+				reg = <0x850 0x8>;
+				#phy-cells = <1>;
+				clocks = <&crg HISTB_COMBPHY0_CLK>;
+				resets = <&crg 0x188 4>;
+				assigned-clocks = <&crg HISTB_COMBPHY0_CLK>;
+				assigned-clock-rates = <100000000>;
+				hisilicon,fixed-mode = <PHY_TYPE_USB3>;
+			};
+
+			combphy1: phy@858 {
+				compatible = "hisilicon,hi3798cv200-combphy";
+				reg = <0x858 0x8>;
+				#phy-cells = <1>;
+				clocks = <&crg HISTB_COMBPHY1_CLK>;
+				resets = <&crg 0x188 12>;
+				assigned-clocks = <&crg HISTB_COMBPHY1_CLK>;
+				assigned-clock-rates = <100000000>;
+				hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>;
+			};
+		};
+
 		uart0: serial@8b00000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x8b00000 0x1000>;
@@ -419,5 +452,35 @@
 			clocks = <&sysctrl HISTB_IR_CLK>;
 			status = "disabled";
 		};
+
+		pcie: pcie@9860000 {
+			compatible = "hisilicon,hi3798cv200-pcie";
+			reg = <0x9860000 0x1000>,
+			      <0x0 0x2000>,
+			      <0x2000000 0x01000000>;
+			reg-names = "control", "rc-dbi", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0 15>;
+			num-lanes = <1>;
+			ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000
+				  0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>;
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0>;
+			interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_PCIE_AUX_CLK>,
+				 <&crg HISTB_PCIE_PIPE_CLK>,
+				 <&crg HISTB_PCIE_SYS_CLK>,
+				 <&crg HISTB_PCIE_BUS_CLK>;
+			clock-names = "aux", "pipe", "sys", "bus";
+			resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
+			reset-names = "soft", "sys", "bus";
+			phys = <&combphy1 PHY_TYPE_PCIE>;
+			phy-names = "phy";
+			status = "disabled";
+		};
 	};
 };
-- 
1.9.1

[PATCH 2/3] arm64: dts: hi3798cv200: enable usb2 support for poplar board

[Shawn Guo]

It adds usb2 phy devices, and enables ehci/ohci support for Hi3798CV200
Poplar board.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
 .../boot/dts/hisilicon/hi3798cv200-poplar.dts      |  8 +++
 arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi     | 68 ++++++++++++++++++++++
 2 files changed, 76 insertions(+)

diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
index c4382e1f3c92..b0b790a5aa8d 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
@@ -72,6 +72,10 @@
 	};
 };
 
+&ehci {
+	status = "okay";
+};
+
 &gmac1 {
 	status = "okay";
 	#address-cells = <1>;
@@ -155,6 +159,10 @@
 	status = "okay";
 };
 
+&ohci {
+	status = "okay";
+};
+
 &pcie {
 	reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
 	vpcie-supply = <&reg_pcie>;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
index 5b73403551e6..c1723ef01cac 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -116,6 +116,42 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x8a20000 0x1000>;
 
+			usb2_phy1: usb2-phy@120 {
+				compatible = "hisilicon,hi3798cv200-usb2-phy";
+				reg = <0x120 0x4>;
+				clocks = <&crg HISTB_USB2_PHY1_REF_CLK>;
+				resets = <&crg 0xbc 4>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb2_phy1_port0: phy@0 {
+					reg = <0>;
+					#phy-cells = <0>;
+					resets = <&crg 0xbc 8>;
+				};
+
+				usb2_phy1_port1: phy@1 {
+					reg = <1>;
+					#phy-cells = <0>;
+					resets = <&crg 0xbc 9>;
+				};
+			};
+
+			usb2_phy2: usb2-phy@124 {
+				compatible = "hisilicon,hi3798cv200-usb2-phy";
+				reg = <0x124 0x4>;
+				clocks = <&crg HISTB_USB2_PHY2_REF_CLK>;
+				resets = <&crg 0xbc 6>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				usb2_phy2_port0: phy@0 {
+					reg = <0>;
+					#phy-cells = <0>;
+					resets = <&crg 0xbc 10>;
+				};
+			};
+
 			combphy0: phy@850 {
 				compatible = "hisilicon,hi3798cv200-combphy";
 				reg = <0x850 0x8>;
@@ -482,5 +518,37 @@
 			phy-names = "phy";
 			status = "disabled";
 		};
+
+		ohci: ohci@9880000 {
+			compatible = "generic-ohci";
+			reg = <0x9880000 0x10000>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_USB2_BUS_CLK>,
+				 <&crg HISTB_USB2_12M_CLK>,
+				 <&crg HISTB_USB2_48M_CLK>;
+			clock-names = "bus", "clk12", "clk48";
+			resets = <&crg 0xb8 12>;
+			reset-names = "bus";
+			phys = <&usb2_phy1_port0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ehci: ehci@9890000 {
+			compatible = "generic-ehci";
+			reg = <0x9890000 0x10000>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&crg HISTB_USB2_BUS_CLK>,
+				 <&crg HISTB_USB2_PHY_CLK>,
+				 <&crg HISTB_USB2_UTMI_CLK>;
+			clock-names = "bus", "phy", "utmi";
+			resets = <&crg 0xb8 12>,
+				 <&crg 0xb8 16>,
+				 <&crg 0xb8 13>;
+			reset-names = "bus", "phy", "utmi";
+			phys = <&usb2_phy1_port0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
 	};
 };
-- 
1.9.1

[PATCH 3/3] arm64: dts: hi3798cv200: enable emmc support for poplar board

[Shawn Guo]

It adds pinctrl device pinconf@8a21000, gpio-ranges for GPIO devices,
and then enables eMMC support for Hi3798CV200 Poplar board.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
 .../boot/dts/hisilicon/hi3798cv200-poplar.dts      | 15 ++++
 arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi     | 74 +++++++++++++++-
 arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi  | 98 ++++++++++++++++++++++
 3 files changed, 184 insertions(+), 3 deletions(-)
 create mode 100644 arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi

diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
index b0b790a5aa8d..d30f6eb8a5ee 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
@@ -11,6 +11,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include "hi3798cv200.dtsi"
+#include "poplar-pinctrl.dtsi"
 
 / {
 	model = "HiSilicon Poplar Development Board";
@@ -76,6 +77,20 @@
 	status = "okay";
 };
 
+&emmc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_pins_1 &emmc_pins_2
+		     &emmc_pins_3 &emmc_pins_4>;
+	fifo-depth = <256>;
+	clock-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	bus-width = <8>;
+	status = "okay";
+};
+
 &gmac1 {
 	status = "okay";
 	#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
index c1723ef01cac..7c0fddd7c8cf 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -175,6 +175,46 @@
 			};
 		};
 
+		pmx0: pinconf@8a21000 {
+			compatible = "pinconf-single";
+			reg = <0x8a21000 0x180>;
+			pinctrl-single,register-width = <32>;
+			pinctrl-single,function-mask = <7>;
+			pinctrl-single,gpio-range = <
+				&range 0  8 2  /* GPIO 0 */
+				&range 8  1 0  /* GPIO 1 */
+				&range 9  4 2
+				&range 13 1 0
+				&range 14 1 1
+				&range 15 1 0
+				&range 16 5 0  /* GPIO 2 */
+				&range 21 3 1
+				&range 24 4 1  /* GPIO 3 */
+				&range 28 2 2
+				&range 86 1 1
+				&range 87 1 0
+				&range 30 4 2  /* GPIO 4 */
+				&range 34 3 0
+				&range 37 1 2
+				&range 38 3 2  /* GPIO 6 */
+				&range 41 5 0
+				&range 46 8 1  /* GPIO 7 */
+				&range 54 8 1  /* GPIO 8 */
+				&range 64 7 1  /* GPIO 9 */
+				&range 71 1 0
+				&range 72 6 1  /* GPIO 10 */
+				&range 78 1 0
+				&range 79 1 1
+				&range 80 6 1  /* GPIO 11 */
+				&range 70 2 1
+				&range 88 8 0  /* GPIO 12 */
+			>;
+
+			range: gpio-range {
+				#pinctrl-single,gpio-range-cells = <3>;
+			};
+		};
+
 		uart0: serial@8b00000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x8b00000 0x1000>;
@@ -274,12 +314,17 @@
 		};
 
 		emmc: mmc@9830000 {
-			compatible = "snps,dw-mshc";
+			compatible = "hisilicon,hi3798cv200-dw-mshc";
 			reg = <0x9830000 0x10000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&crg HISTB_MMC_CIU_CLK>,
-				 <&crg HISTB_MMC_BIU_CLK>;
-			clock-names = "ciu", "biu";
+				 <&crg HISTB_MMC_BIU_CLK>,
+				 <&crg HISTB_MMC_SAMPLE_CLK>,
+				 <&crg HISTB_MMC_DRV_CLK>;
+			clock-names = "ciu", "biu", "ciu-sample", "ciu-drive";
+			resets = <&crg 0xa0 4>;
+			reset-names = "reset";
+			status = "disabled";
 		};
 
 		gpio0: gpio@8b20000 {
@@ -290,6 +335,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 0 8>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -303,6 +349,13 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <
+				&pmx0 0 8 1
+				&pmx0 1 9 4
+				&pmx0 5 13 1
+				&pmx0 6 14 1
+				&pmx0 7 15 1
+			>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -316,6 +369,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 16 5 &pmx0 5 21 3>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -329,6 +383,12 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <
+				&pmx0 0 24 4
+				&pmx0 4 28 2
+				&pmx0 6 86 1
+				&pmx0 7 87 1
+			>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -342,6 +402,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 30 4 &pmx0 4 34 3 &pmx0 7 37 1>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -368,6 +429,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 38 3 &pmx0 0 41 5>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -381,6 +443,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 46 8>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -394,6 +457,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 54 8>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -407,6 +471,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 64 7 &pmx0 71 1>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -420,6 +485,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 72 6 &pmx0 6 78 1 &pmx0 7 79 1>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -433,6 +499,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 80 6 &pmx0 6 70 2>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
@@ -446,6 +513,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			gpio-ranges = <&pmx0 0 88 8>;
 			clocks = <&crg HISTB_APB_CLK>;
 			clock-names = "apb_pclk";
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi
new file mode 100644
index 000000000000..7bb19e4b084a
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Pinctrl dts file for HiSilicon Poplar board
+ *
+ * Copyright (c) 2016-2018 HiSilicon Technologies Co., Ltd.
+ */
+
+#include <dt-bindings/pinctrl/hisi.h>
+
+/* value, enable bits, disable bits, mask */
+#define PINCTRL_PULLDOWN(value, enable, disable, mask) \
+	(value << 13) (enable << 13) (disable << 13) (mask << 13)
+#define PINCTRL_PULLUP(value, enable, disable, mask) \
+	(value << 12) (enable << 12) (disable << 12) (mask << 12)
+#define PINCTRL_SLEW_RATE(value, mask)	  (value << 8) (mask << 8)
+#define PINCTRL_DRV_STRENGTH(value, mask) (value << 4) (mask << 4)
+
+&pmx0 {
+	emmc_pins_1: emmc-pins-1 {
+		pinctrl-single,pins = <
+			0x000 MUX_M2
+			0x004 MUX_M2
+			0x008 MUX_M2
+			0x00c MUX_M2
+			0x010 MUX_M2
+			0x014 MUX_M2
+			0x018 MUX_M2
+			0x01c MUX_M2
+			0x024 MUX_M2
+		>;
+		pinctrl-single,bias-pulldown = <
+			PINCTRL_PULLDOWN(0, 1, 0, 1)
+		>;
+		pinctrl-single,bias-pullup = <
+			PINCTRL_PULLUP(0, 1, 0, 1)
+		>;
+		pinctrl-single,slew-rate = <
+			PINCTRL_SLEW_RATE(1, 1)
+		>;
+		pinctrl-single,drive-strength = <
+			PINCTRL_DRV_STRENGTH(0xb, 0xf)
+		>;
+	};
+
+	emmc_pins_2: emmc-pins-2 {
+		pinctrl-single,pins = <
+			0x028 MUX_M2
+		>;
+		pinctrl-single,bias-pulldown = <
+			PINCTRL_PULLDOWN(0, 1, 0, 1)
+		>;
+		pinctrl-single,bias-pullup = <
+			PINCTRL_PULLUP(0, 1, 0, 1)
+		>;
+		pinctrl-single,slew-rate = <
+			PINCTRL_SLEW_RATE(1, 1)
+		>;
+		pinctrl-single,drive-strength = <
+			PINCTRL_DRV_STRENGTH(0x9, 0xf)
+		>;
+	};
+
+	emmc_pins_3: emmc-pins-3 {
+		pinctrl-single,pins = <
+			0x02c MUX_M2
+		>;
+		pinctrl-single,bias-pulldown = <
+			PINCTRL_PULLDOWN(0, 1, 0, 1)
+		>;
+		pinctrl-single,bias-pullup = <
+			PINCTRL_PULLUP(0, 1, 0, 1)
+		>;
+		pinctrl-single,slew-rate = <
+			PINCTRL_SLEW_RATE(1, 1)
+		>;
+		pinctrl-single,drive-strength = <
+			PINCTRL_DRV_STRENGTH(3, 3)
+		>;
+	};
+
+	emmc_pins_4: emmc-pins-4 {
+		pinctrl-single,pins = <
+			0x030 MUX_M2
+		>;
+		pinctrl-single,bias-pulldown = <
+			PINCTRL_PULLDOWN(1, 1, 0, 1)
+		>;
+		pinctrl-single,bias-pullup = <
+			PINCTRL_PULLUP(0, 1, 0, 1)
+		>;
+		pinctrl-single,slew-rate = <
+			PINCTRL_SLEW_RATE(1, 1)
+		>;
+		pinctrl-single,drive-strength = <
+			PINCTRL_DRV_STRENGTH(3, 3)
+		>;
+	};
+};
-- 
1.9.1

Re: [PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe support for poplar board

[Wei Xu]

Hi Shawn,

On 2018/5/11 3:03, Shawn Guo wrote:
> It adds combophy devices under peripheral controller and enables PCIe
> support for Hi3798CV200 Poplar board.
> 
> Signed-off-by: Shawn Guo <shawn.guo@linaro.org>

Series applied into the hisilicon dt tree.
Thanks!

BR,
Wei

> ---
>  .../boot/dts/hisilicon/hi3798cv200-poplar.dts      | 15 ++++++
>  arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi     | 63 ++++++++++++++++++++++
>  2 files changed, 78 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> index 4d5d644abb12..c4382e1f3c92 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
> @@ -61,6 +61,15 @@
>  			default-state = "off";
>  		};
>  	};
> +
> +	reg_pcie: regulator-pcie {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3V3_PCIE0";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio6 7 0>;
> +		enable-active-high;
> +	};
>  };
>  
>  &gmac1 {
> @@ -146,6 +155,12 @@
>  	status = "okay";
>  };
>  
> +&pcie {
> +	reset-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
> +	vpcie-supply = <&reg_pcie>;
> +	status = "okay";
> +};
> +
>  &sd0 {
>  	bus-width = <4>;
>  	cap-sd-highspeed;
> diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> index 962bd79139e4..5b73403551e6 100644
> --- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> +++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
> @@ -8,7 +8,9 @@
>   */
>  
>  #include <dt-bindings/clock/histb-clock.h>
> +#include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/phy/phy.h>
>  #include <dt-bindings/reset/ti-syscon.h>
>  
>  / {
> @@ -106,6 +108,37 @@
>  			#reset-cells = <2>;
>  		};
>  
> +		perictrl: peripheral-controller@8a20000 {
> +			compatible = "hisilicon,hi3798cv200-perictrl", "syscon",
> +				     "simple-mfd";
> +			reg = <0x8a20000 0x1000>;
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges = <0x0 0x8a20000 0x1000>;
> +
> +			combphy0: phy@850 {
> +				compatible = "hisilicon,hi3798cv200-combphy";
> +				reg = <0x850 0x8>;
> +				#phy-cells = <1>;
> +				clocks = <&crg HISTB_COMBPHY0_CLK>;
> +				resets = <&crg 0x188 4>;
> +				assigned-clocks = <&crg HISTB_COMBPHY0_CLK>;
> +				assigned-clock-rates = <100000000>;
> +				hisilicon,fixed-mode = <PHY_TYPE_USB3>;
> +			};
> +
> +			combphy1: phy@858 {
> +				compatible = "hisilicon,hi3798cv200-combphy";
> +				reg = <0x858 0x8>;
> +				#phy-cells = <1>;
> +				clocks = <&crg HISTB_COMBPHY1_CLK>;
> +				resets = <&crg 0x188 12>;
> +				assigned-clocks = <&crg HISTB_COMBPHY1_CLK>;
> +				assigned-clock-rates = <100000000>;
> +				hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>;
> +			};
> +		};
> +
>  		uart0: serial@8b00000 {
>  			compatible = "arm,pl011", "arm,primecell";
>  			reg = <0x8b00000 0x1000>;
> @@ -419,5 +452,35 @@
>  			clocks = <&sysctrl HISTB_IR_CLK>;
>  			status = "disabled";
>  		};
> +
> +		pcie: pcie@9860000 {
> +			compatible = "hisilicon,hi3798cv200-pcie";
> +			reg = <0x9860000 0x1000>,
> +			      <0x0 0x2000>,
> +			      <0x2000000 0x01000000>;
> +			reg-names = "control", "rc-dbi", "config";
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +			device_type = "pci";
> +			bus-range = <0 15>;
> +			num-lanes = <1>;
> +			ranges = <0x81000000 0x0 0x00000000 0x4f00000 0x0 0x100000
> +				  0x82000000 0x0 0x3000000 0x3000000 0x0 0x01f00000>;
> +			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0>;
> +			interrupt-map = <0 0 0 0 &gic 0 131 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&crg HISTB_PCIE_AUX_CLK>,
> +				 <&crg HISTB_PCIE_PIPE_CLK>,
> +				 <&crg HISTB_PCIE_SYS_CLK>,
> +				 <&crg HISTB_PCIE_BUS_CLK>;
> +			clock-names = "aux", "pipe", "sys", "bus";
> +			resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>;
> +			reset-names = "soft", "sys", "bus";
> +			phys = <&combphy1 PHY_TYPE_PCIE>;
> +			phy-names = "phy";
> +			status = "disabled";
> +		};
>  	};
>  };
>