From: Shawn Guo <shawn.guo@linaro.org>
To: Wei Xu <xuwei5@hisilicon.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>,
Jiancheng Xue <xuejiancheng@hisilicon.com>,
Shawn Guo <shawn.guo@linaro.org>,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org
Subject: [PATCH 3/3] arm64: dts: hi3798cv200: enable emmc support for poplar board
Date: Fri, 11 May 2018 10:03:40 +0800 [thread overview]
Message-ID: <1526004220-17030-3-git-send-email-shawn.guo@linaro.org> (raw)
In-Reply-To: <1526004220-17030-1-git-send-email-shawn.guo@linaro.org>
It adds pinctrl device pinconf@8a21000, gpio-ranges for GPIO devices,
and then enables eMMC support for Hi3798CV200 Poplar board.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
.../boot/dts/hisilicon/hi3798cv200-poplar.dts | 15 ++++
arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi | 74 +++++++++++++++-
arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi | 98 ++++++++++++++++++++++
3 files changed, 184 insertions(+), 3 deletions(-)
create mode 100644 arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
index b0b790a5aa8d..d30f6eb8a5ee 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200-poplar.dts
@@ -11,6 +11,7 @@
#include <dt-bindings/gpio/gpio.h>
#include "hi3798cv200.dtsi"
+#include "poplar-pinctrl.dtsi"
/ {
model = "HiSilicon Poplar Development Board";
@@ -76,6 +77,20 @@
status = "okay";
};
+&emmc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&emmc_pins_1 &emmc_pins_2
+ &emmc_pins_3 &emmc_pins_4>;
+ fifo-depth = <256>;
+ clock-frequency = <200000000>;
+ cap-mmc-highspeed;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ non-removable;
+ bus-width = <8>;
+ status = "okay";
+};
+
&gmac1 {
status = "okay";
#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
index c1723ef01cac..7c0fddd7c8cf 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3798cv200.dtsi
@@ -175,6 +175,46 @@
};
};
+ pmx0: pinconf@8a21000 {
+ compatible = "pinconf-single";
+ reg = <0x8a21000 0x180>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <7>;
+ pinctrl-single,gpio-range = <
+ &range 0 8 2 /* GPIO 0 */
+ &range 8 1 0 /* GPIO 1 */
+ &range 9 4 2
+ &range 13 1 0
+ &range 14 1 1
+ &range 15 1 0
+ &range 16 5 0 /* GPIO 2 */
+ &range 21 3 1
+ &range 24 4 1 /* GPIO 3 */
+ &range 28 2 2
+ &range 86 1 1
+ &range 87 1 0
+ &range 30 4 2 /* GPIO 4 */
+ &range 34 3 0
+ &range 37 1 2
+ &range 38 3 2 /* GPIO 6 */
+ &range 41 5 0
+ &range 46 8 1 /* GPIO 7 */
+ &range 54 8 1 /* GPIO 8 */
+ &range 64 7 1 /* GPIO 9 */
+ &range 71 1 0
+ &range 72 6 1 /* GPIO 10 */
+ &range 78 1 0
+ &range 79 1 1
+ &range 80 6 1 /* GPIO 11 */
+ &range 70 2 1
+ &range 88 8 0 /* GPIO 12 */
+ >;
+
+ range: gpio-range {
+ #pinctrl-single,gpio-range-cells = <3>;
+ };
+ };
+
uart0: serial@8b00000 {
compatible = "arm,pl011", "arm,primecell";
reg = <0x8b00000 0x1000>;
@@ -274,12 +314,17 @@
};
emmc: mmc@9830000 {
- compatible = "snps,dw-mshc";
+ compatible = "hisilicon,hi3798cv200-dw-mshc";
reg = <0x9830000 0x10000>;
interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&crg HISTB_MMC_CIU_CLK>,
- <&crg HISTB_MMC_BIU_CLK>;
- clock-names = "ciu", "biu";
+ <&crg HISTB_MMC_BIU_CLK>,
+ <&crg HISTB_MMC_SAMPLE_CLK>,
+ <&crg HISTB_MMC_DRV_CLK>;
+ clock-names = "ciu", "biu", "ciu-sample", "ciu-drive";
+ resets = <&crg 0xa0 4>;
+ reset-names = "reset";
+ status = "disabled";
};
gpio0: gpio@8b20000 {
@@ -290,6 +335,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 0 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -303,6 +349,13 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <
+ &pmx0 0 8 1
+ &pmx0 1 9 4
+ &pmx0 5 13 1
+ &pmx0 6 14 1
+ &pmx0 7 15 1
+ >;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -316,6 +369,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 16 5 &pmx0 5 21 3>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -329,6 +383,12 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <
+ &pmx0 0 24 4
+ &pmx0 4 28 2
+ &pmx0 6 86 1
+ &pmx0 7 87 1
+ >;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -342,6 +402,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 30 4 &pmx0 4 34 3 &pmx0 7 37 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -368,6 +429,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 38 3 &pmx0 0 41 5>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -381,6 +443,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 46 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -394,6 +457,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 54 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -407,6 +471,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 64 7 &pmx0 71 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -420,6 +485,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 72 6 &pmx0 6 78 1 &pmx0 7 79 1>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -433,6 +499,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 80 6 &pmx0 6 70 2>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
@@ -446,6 +513,7 @@
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
+ gpio-ranges = <&pmx0 0 88 8>;
clocks = <&crg HISTB_APB_CLK>;
clock-names = "apb_pclk";
status = "disabled";
diff --git a/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi b/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi
new file mode 100644
index 000000000000..7bb19e4b084a
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/poplar-pinctrl.dtsi
@@ -0,0 +1,98 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Pinctrl dts file for HiSilicon Poplar board
+ *
+ * Copyright (c) 2016-2018 HiSilicon Technologies Co., Ltd.
+ */
+
+#include <dt-bindings/pinctrl/hisi.h>
+
+/* value, enable bits, disable bits, mask */
+#define PINCTRL_PULLDOWN(value, enable, disable, mask) \
+ (value << 13) (enable << 13) (disable << 13) (mask << 13)
+#define PINCTRL_PULLUP(value, enable, disable, mask) \
+ (value << 12) (enable << 12) (disable << 12) (mask << 12)
+#define PINCTRL_SLEW_RATE(value, mask) (value << 8) (mask << 8)
+#define PINCTRL_DRV_STRENGTH(value, mask) (value << 4) (mask << 4)
+
+&pmx0 {
+ emmc_pins_1: emmc-pins-1 {
+ pinctrl-single,pins = <
+ 0x000 MUX_M2
+ 0x004 MUX_M2
+ 0x008 MUX_M2
+ 0x00c MUX_M2
+ 0x010 MUX_M2
+ 0x014 MUX_M2
+ 0x018 MUX_M2
+ 0x01c MUX_M2
+ 0x024 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(0xb, 0xf)
+ >;
+ };
+
+ emmc_pins_2: emmc-pins-2 {
+ pinctrl-single,pins = <
+ 0x028 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(0x9, 0xf)
+ >;
+ };
+
+ emmc_pins_3: emmc-pins-3 {
+ pinctrl-single,pins = <
+ 0x02c MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(0, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(3, 3)
+ >;
+ };
+
+ emmc_pins_4: emmc-pins-4 {
+ pinctrl-single,pins = <
+ 0x030 MUX_M2
+ >;
+ pinctrl-single,bias-pulldown = <
+ PINCTRL_PULLDOWN(1, 1, 0, 1)
+ >;
+ pinctrl-single,bias-pullup = <
+ PINCTRL_PULLUP(0, 1, 0, 1)
+ >;
+ pinctrl-single,slew-rate = <
+ PINCTRL_SLEW_RATE(1, 1)
+ >;
+ pinctrl-single,drive-strength = <
+ PINCTRL_DRV_STRENGTH(3, 3)
+ >;
+ };
+};
--
1.9.1
next prev parent reply other threads:[~2018-05-11 2:03 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-11 2:03 [PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe support for poplar board Shawn Guo
2018-05-11 2:03 ` [PATCH 2/3] arm64: dts: hi3798cv200: enable usb2 " Shawn Guo
2018-05-11 2:03 ` Shawn Guo [this message]
2018-05-11 13:58 ` [PATCH 1/3] arm64: dts: hi3798cv200: enable PCIe " Wei Xu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1526004220-17030-3-git-send-email-shawn.guo@linaro.org \
--to=shawn.guo@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=sunjianguo1@huawei.com \
--cc=xuejiancheng@hisilicon.com \
--cc=xuwei5@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).