* [PATCH v3 1/9] ARM: dts: s5pv210: Add missing interrupt-controller property to gph2
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-07 8:38 ` Krzysztof Kozlowski
2018-07-06 18:32 ` [PATCH v3 2/9] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones Paweł Chmiel
` (8 subsequent siblings)
9 siblings, 1 reply; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: devicetree, linux-samsung-soc, xc-racer2, linux-kernel,
linux-arm-kernel, pawel.mikolaj.chmiel
Adds missing interrupt-controller property to gph2 block,
to silence following warnings during build
/soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
It's reguired by Samsung aries boards, an S5PV210 based
Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi b/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
index 3a79feab11c3..7f0c9d447871 100644
--- a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
@@ -258,6 +258,8 @@
gph2: gph2 {
gpio-controller;
#gpio-cells = <2>;
+
+ interrupt-controller;
#interrupt-cells = <2>;
};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 1/9] ARM: dts: s5pv210: Add missing interrupt-controller property to gph2
2018-07-06 18:32 ` [PATCH v3 1/9] ARM: dts: s5pv210: Add missing interrupt-controller property to gph2 Paweł Chmiel
@ 2018-07-07 8:38 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:38 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:42PM +0200, Paweł Chmiel wrote:
> Adds missing interrupt-controller property to gph2 block,
> to silence following warnings during build
> /soc/pinctrl@e0200000/gph2: Missing interrupt-controller or interrupt-map property
>
> It's reguired by Samsung aries boards, an S5PV210 based
> Samsung Galaxy S (i9000) and Galaxy S 4G phones, which are added in next patches.
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> arch/arm/boot/dts/s5pv210-pinctrl.dtsi | 2 ++
> 1 file changed, 2 insertions(+)
>
Thanks, applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 2/9] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 1/9] ARM: dts: s5pv210: Add missing interrupt-controller property to gph2 Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-07 8:43 ` Krzysztof Kozlowski
2018-07-06 18:32 ` [PATCH v3 3/9] ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone Paweł Chmiel
` (7 subsequent siblings)
9 siblings, 1 reply; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: devicetree, linux-samsung-soc, xc-racer2, linux-kernel,
linux-arm-kernel, pawel.mikolaj.chmiel
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
Changes from v2:
- Restored pinctrl nodes order
- Correct order of nodes
Changes from v1:
- Removed duplicated and unneeded headers
- Corrected node names
- Added missing spaces
- Removed unneeded pinctrl and sorted entries
- Set correct interrupt type for max8998 pmic
- Add missing regulators
---
---
arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++
1 file changed, 423 insertions(+)
create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
new file mode 100644
index 000000000000..0dfba52e1cdb
--- /dev/null
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -0,0 +1,423 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's S5PV210 based Galaxy Aries board device tree source
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "s5pv210.dtsi"
+
+/ {
+ compatible = "samsung,aries", "samsung,s5pv210";
+
+ aliases {
+ i2c6 = &i2c_pmic;
+ i2c9 = &i2c_fuel;
+ };
+
+ memory@30000000 {
+ device_type = "memory";
+ reg = <0x30000000 0x05000000
+ 0x40000000 0x10000000
+ 0x50000000 0x08000000>;
+ };
+
+ wifi_pwrseq: wifi-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_gpio_rst>;
+ post-power-on-delay-ms = <500>;
+ power-off-delay-us = <500>;
+ };
+
+ i2c_pmic: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pmic@66 {
+ compatible = "maxim,max8998";
+ reg = <0x66>;
+ interrupt-parent = <&gph0>;
+ interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+ max8998,pmic-buck1-default-dvs-idx = <1>;
+ max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
+ <&gph0 4 GPIO_ACTIVE_HIGH>;
+ max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
+ <1050000>, <950000>;
+
+ max8998,pmic-buck2-default-dvs-idx = <0>;
+ max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
+ max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
+
+ regulators {
+ ldo2_reg: LDO2 {
+ regulator-name = "VALIVE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VUSB_1.1V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VADC_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VTF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "LDO6";
+ regulator-min-microvolt = <1600000>;
+ regulator-max-microvolt = <3600000>;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VLCD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ /* Till we get panel driver */
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VUSB_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "VCC_2.8V_PDA";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "VPLL_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "CAM_AF_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "CAM_SENSOR_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "VGA_VDDIO_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "VGA_DVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "CAM_ISP_HOST_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "VGA_AVDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "VCC_3.0V_LCD";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ /* Till we get panel driver */
+ regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vddarm";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1250000>;
+ };
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "vddint";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1500000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1100000>;
+ };
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VCC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "CAM_ISP_CORE_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ ap32khz_reg: EN32KHz-AP {
+ regulator-name = "32KHz AP";
+ regulator-always-on;
+ };
+
+ cp32khz_reg: EN32KHz-CP {
+ regulator-name = "32KHz CP";
+ };
+
+ vichg_reg: ENVICHG {
+ regulator-name = "VICHG";
+ regulator-always-on;
+ };
+
+ safe1_sreg: ESAFEOUT1 {
+ regulator-name = "SAFEOUT1";
+ };
+
+ safe2_sreg: ESAFEOUT2 {
+ regulator-name = "SAFEOUT2";
+ };
+ };
+ };
+ };
+
+ i2c_fuel: i2c-gpio-1 {
+ compatible = "i2c-gpio";
+ sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+ i2c-gpio,delay-us = <2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ fuelgauge@36 {
+ compatible = "maxim,max17040";
+ interrupt-parent = <&vic0>;
+ interrupts = <7>;
+ reg = <0x36>;
+ };
+ };
+};
+
+&fimd {
+ pinctrl-names = "default";
+ pinctrl-0 = <&lcd_clk &lcd_data24>;
+ status = "okay";
+
+ samsung,invert-vden;
+ samsung,invert-vclk;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ display-timings {
+ native-mode = <&timing0>;
+
+ timing0: timing@0 {
+ /* 480x800@60Hz */
+ clock-frequency = <25628040>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <16>;
+ hback-porch = <16>;
+ hsync-len = <2>;
+ vfront-porch = <28>;
+ vback-porch = <1>;
+ vsync-len = <2>;
+ };
+ };
+};
+
+&hsotg {
+ vusb_a-supply = <&ldo8_reg>;
+ vusb_d-supply = <&ldo3_reg>;
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&pinctrl0 {
+ wlan_bt_en: wlan-bt-en {
+ samsung,pins = "gpb-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-val = <1>;
+ };
+
+ wlan_gpio_rst: wlan-gpio-rst {
+ samsung,pins = "gpg1-2";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ };
+
+ wifi_host_wake: wifi-host-wake {
+ samsung,pins = "gph2-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ tf_detect: tf-detect {
+ samsung,pins = "gph3-4";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+
+ wifi_wake: wifi-wake {
+ samsung,pins = "gph3-5";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ };
+};
+
+&sdhci1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bus-width = <4>;
+ max-frequency = <38400000>;
+ pinctrl-0 = <&sd1_clk &sd1_cmd &sd1_bus4 &wifi_wake &wifi_host_wake &wlan_bt_en>;
+ pinctrl-names = "default";
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+
+ mmc-pwrseq = <&wifi_pwrseq>;
+ non-removable;
+ status = "okay";
+
+ wlan@1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&gph2>;
+ interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "host-wake";
+ };
+};
+
+&sdhci2 {
+ bus-width = <4>;
+ cd-gpios = <&gph3 4 GPIO_ACTIVE_LOW>;
+ vmmc-supply = <&ldo5_reg>;
+ pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &tf_detect>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&uart1 {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+ vbus-supply = <&safe1_sreg>;
+};
+
+&xusbxti {
+ clock-frequency = <24000000>;
+};
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 2/9] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones
2018-07-06 18:32 ` [PATCH v3 2/9] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones Paweł Chmiel
@ 2018-07-07 8:43 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:43 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:43PM +0200, Paweł Chmiel wrote:
> This DTS file have initial support Samsung Aries based phones.
> Initial version have support for:
> - sdcard
> - internal memory (present only on non 4g variant)
> - max8998 pmic and rtc
> - max17040 fuel gauge
> - gpio keys
> - fimd (no panel driver yet)
> - usb (peripherial mode)
> - wifi
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> Changes from v2:
> - Restored pinctrl nodes order
> - Correct order of nodes
>
> Changes from v1:
> - Removed duplicated and unneeded headers
> - Corrected node names
> - Added missing spaces
> - Removed unneeded pinctrl and sorted entries
> - Set correct interrupt type for max8998 pmic
> - Add missing regulators
> ---
> ---
I applied this and 3/9 but then dtc complained about warnings
make dtbs W=1:
arch/arm/boot/dts/s5pv210-galaxys.dtb: Warning (unit_address_vs_reg): /soc/fimd@f8000000/display-timings/timing@0: node has a unit name, but no reg property
arch/arm/boot/dts/s5pv210-galaxys.dtb: Warning (avoid_unnecessary_addr_size): /soc/fimd@f8000000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
These should be fixed (unless such warning come from following bindings,
e.g. like in case of ports for Exynos HDMI nodes).
Please, always run dtbs W=1 for DTS patches, check with sparse for
regular code and checkpatch for everything. Checks with smatch
and coccinelle are also appreciated (although coccinelle is run by
kbuild bot).
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 3/9] ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 1/9] ARM: dts: s5pv210: Add missing interrupt-controller property to gph2 Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 2/9] ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 4/9] ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone Paweł Chmiel
` (6 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
This DTS file have initial support Samsung Galaxy S phone,
also known as i9000.
It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- internal memory
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
--
Changes from v1:
- Added missing commit msg
- Removed duplicated and unneeded headers
- Added stdout-path
- Added information why we hardcode bootargs
---
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/s5pv210-galaxys.dts | 77 +++++++++++++++++++++++++++++++++++
2 files changed, 78 insertions(+)
create mode 100644 arch/arm/boot/dts/s5pv210-galaxys.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 7e2424957809..522ebdca1d3d 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -846,6 +846,7 @@ dtb-$(CONFIG_ARCH_S3C64XX) += \
s3c6410-smdk6410.dtb
dtb-$(CONFIG_ARCH_S5PV210) += \
s5pv210-aquila.dtb \
+ s5pv210-galaxys.dtb \
s5pv210-goni.dtb \
s5pv210-smdkc110.dtb \
s5pv210-smdkv210.dtb \
diff --git a/arch/arm/boot/dts/s5pv210-galaxys.dts b/arch/arm/boot/dts/s5pv210-galaxys.dts
new file mode 100644
index 000000000000..842276749717
--- /dev/null
+++ b/arch/arm/boot/dts/s5pv210-galaxys.dts
@@ -0,0 +1,77 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "s5pv210-aries.dtsi"
+
+/ {
+ model = "Samsung Galaxy S1 (GT-I9000) based on S5PV210";
+ compatible = "samsung,galaxys", "samsung,aries", "samsung,s5pv210";
+
+ chosen {
+ stdout-path = &uart2;
+ /*
+ * It's hard to change those parameters in stock bootloader,
+ * since it requires special hardware/cable.
+ * Let's hardocde bootargs for now, till u-boot port is finished,
+ * with which it should be easier.
+ */
+ bootargs = "root=/dev/mmcblk2p1 rw rootwait ignore_loglevel earlyprintk";
+ };
+
+ nand_pwrseq: nand-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&gpj2 7 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&massmemory_en>;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "power";
+ gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ vol-down {
+ label = "volume_down";
+ gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ vol-up {
+ label = "volume_up";
+ gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+
+ home {
+ label = "home";
+ gpios = <&gph3 5 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_HOME>;
+ wakeup-source;
+ };
+ };
+};
+
+&pinctrl0 {
+ massmemory_en: massmemory-en {
+ samsung,pins = "gpj2-7";
+ samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+ samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+ samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+ };
+};
+
+&sdhci0 {
+ bus-width = <4>;
+ non-removable;
+ mmc-pwrseq = <&nand_pwrseq>;
+ pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>;
+ pinctrl-names = "default";
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 4/9] ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (2 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 3/9] ARM: dts: s5pv210: Add initial DTS for Samsung Galaxy S phone Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 5/9] dt-bindings: samsung: Document bindings for Samsung aries boards Paweł Chmiel
` (5 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
From: Jonathan Bakker <xc-racer2@live.ca>
This DTS file have initial support Samsung SGH-T959P phone,
also known as Samsung Galaxy S 4G or fascinate4g.
It belongs to Samsung Aries devices family.
Initial version have support for:
- sdcard
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
Changes from v1:
- Added missing commit msg
- Removed duplicated and unneeded headers
- Added stdout-path
- Added information why we hardcode bootargs
---
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/s5pv210-fascinate4g.dts | 45 +++++++++++++++++++++++++++++++
2 files changed, 46 insertions(+)
create mode 100644 arch/arm/boot/dts/s5pv210-fascinate4g.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 522ebdca1d3d..d00e995875bb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -846,6 +846,7 @@ dtb-$(CONFIG_ARCH_S3C64XX) += \
s3c6410-smdk6410.dtb
dtb-$(CONFIG_ARCH_S5PV210) += \
s5pv210-aquila.dtb \
+ s5pv210-fascinate4g.dtb \
s5pv210-galaxys.dtb \
s5pv210-goni.dtb \
s5pv210-smdkc110.dtb \
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
new file mode 100644
index 000000000000..ccf761b1babf
--- /dev/null
+++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "s5pv210-aries.dtsi"
+
+/ {
+ model = "Samsung Galaxy S Fascinate 4G (SGH-T959P) based on S5PV210";
+ compatible = "samsung,fascinate4g", "samsung,aries", "samsung,s5pv210";
+
+ chosen {
+ stdout-path = &uart2;
+ /*
+ * It's hard to change those parameters in stock bootloader,
+ * since it requires special hardware/cable.
+ * Let's hardocde bootargs for now, till u-boot port is finished,
+ * with which it should be easier.
+ */
+ bootargs = "root=/dev/mmcblk1p1 rw rootwait ignore_loglevel earlyprintk";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ power {
+ label = "power";
+ gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ vol-down {
+ label = "volume_down";
+ gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEDOWN>;
+ };
+
+ vol-up {
+ label = "volume_up";
+ gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 5/9] dt-bindings: samsung: Document bindings for Samsung aries boards
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (3 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 4/9] ARM: dts: s5pv210: Add initial DTS for SGH-T959P phone Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 6/9] dt-bindings: samsung: Document bindings for SGH-T959P board Paweł Chmiel
` (4 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: devicetree, linux-samsung-soc, xc-racer2, linux-kernel,
linux-arm-kernel, pawel.mikolaj.chmiel
Document the binding for Samsung Galaxy S (i9000) phone
and whole Samsung Aries devices family (based on S5PV210).
Also because this is first not Exynos-based devices, document this information
at beginning of file.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
--
Changes from v2:
- Squashed with patch which was documenting existence
of non Exynos-based boards
- Added reviewed-by
Changes from v1:
- Added missing commit msg.
--
---
Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
index 14510b215480..3fa287a86300 100644
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
@@ -1,7 +1,9 @@
-* Samsung's Exynos SoC based boards
+* Samsung's Exynos and S5P SoC based boards
Required root node properties:
- compatible = should be one or more of the following.
+ - "samsung,aries" - for S5PV210-based Samsung Aries board.
+ - "samsung,galaxys" - for S5PV210-based Samsung Galaxy S (i9000) board.
- "samsung,artik5" - for Exynos3250-based Samsung ARTIK5 module.
- "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board.
- "samsung,monk" - for Exynos3250-based Samsung Simband board.
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 6/9] dt-bindings: samsung: Document bindings for SGH-T959P board
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (4 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 5/9] dt-bindings: samsung: Document bindings for Samsung aries boards Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-06 18:32 ` [PATCH v3 7/9] ARM: s5pv210_defconfig: Run make savedefconfig Paweł Chmiel
` (3 subsequent siblings)
9 siblings, 0 replies; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
From: Jonathan Bakker <xc-racer2@live.ca>
Document the binding for Samsung Galaxy S Fascinate 4G (SGH-T959P).
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
--
Changes from v2:
- Added Acked-by
Changes from v1:
- Added missing commit msg.
--
---
Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
index 3fa287a86300..37e96e48c48c 100644
--- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
+++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
@@ -3,6 +3,7 @@
Required root node properties:
- compatible = should be one or more of the following.
- "samsung,aries" - for S5PV210-based Samsung Aries board.
+ - "samsung,fascinate4g" - for S5PV210-based Samsung Galaxy S Fascinate 4G (SGH-T959P) board.
- "samsung,galaxys" - for S5PV210-based Samsung Galaxy S (i9000) board.
- "samsung,artik5" - for Exynos3250-based Samsung ARTIK5 module.
- "samsung,artik5-eval" - for Exynos3250-based Samsung ARTIK5 eval board.
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* [PATCH v3 7/9] ARM: s5pv210_defconfig: Run make savedefconfig
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (5 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 6/9] dt-bindings: samsung: Document bindings for SGH-T959P board Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-07 8:46 ` Krzysztof Kozlowski
2018-07-06 18:32 ` [PATCH v3 8/9] ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones Paweł Chmiel
` (2 subsequent siblings)
9 siblings, 1 reply; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
This is result of running savedefconfig.
It's preparation for adding support for Samsung Aries devices.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
arch/arm/configs/s5pv210_defconfig | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/configs/s5pv210_defconfig b/arch/arm/configs/s5pv210_defconfig
index 09b5a7386414..9c862d366fb3 100644
--- a/arch/arm/configs/s5pv210_defconfig
+++ b/arch/arm/configs/s5pv210_defconfig
@@ -13,7 +13,6 @@ CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_ARCH_S5PV210=y
CONFIG_VMSPLIT_2G=y
CONFIG_PREEMPT=y
-CONFIG_AEABI=y
CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x20800000,8M console=ttySAC1,115200 init=/linuxrc"
CONFIG_VFP=y
CONFIG_NEON=y
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 7/9] ARM: s5pv210_defconfig: Run make savedefconfig
2018-07-06 18:32 ` [PATCH v3 7/9] ARM: s5pv210_defconfig: Run make savedefconfig Paweł Chmiel
@ 2018-07-07 8:46 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:46 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:48PM +0200, Paweł Chmiel wrote:
> This is result of running savedefconfig.
> It's preparation for adding support for Samsung Aries devices.
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> arch/arm/configs/s5pv210_defconfig | 1 -
> 1 file changed, 1 deletion(-)
>
Thanks, applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 8/9] ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (6 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 7/9] ARM: s5pv210_defconfig: Run make savedefconfig Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-07 8:49 ` Krzysztof Kozlowski
2018-07-06 18:32 ` [PATCH v3 9/9] ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro Paweł Chmiel
2018-07-07 8:52 ` [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Krzysztof Kozlowski
9 siblings, 1 reply; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
Enable config options required for Samsung Aries based phones.
ARM_APPENDED_DTB is also needed, because stock bootloader
does not support loading dtb files.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
arch/arm/configs/s5pv210_defconfig | 33 +++++++++++++++++++++++++++++++--
1 file changed, 31 insertions(+), 2 deletions(-)
diff --git a/arch/arm/configs/s5pv210_defconfig b/arch/arm/configs/s5pv210_defconfig
index 9c862d366fb3..f719e7f9a655 100644
--- a/arch/arm/configs/s5pv210_defconfig
+++ b/arch/arm/configs/s5pv210_defconfig
@@ -13,9 +13,12 @@ CONFIG_SOLARIS_X86_PARTITION=y
CONFIG_ARCH_S5PV210=y
CONFIG_VMSPLIT_2G=y
CONFIG_PREEMPT=y
+CONFIG_ARM_APPENDED_DTB=y
CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x20800000,8M console=ttySAC1,115200 init=/linuxrc"
CONFIG_VFP=y
CONFIG_NEON=y
+CONFIG_NET=y
+CONFIG_CFG80211=m
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
@@ -23,16 +26,42 @@ CONFIG_BLK_DEV_RAM_SIZE=8192
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_CHR_DEV_SG=y
+CONFIG_NETDEVICES=y
+CONFIG_BRCMFMAC=m
CONFIG_INPUT_EVDEV=y
-# CONFIG_INPUT_KEYBOARD is not set
+CONFIG_KEYBOARD_GPIO=y
# CONFIG_INPUT_MOUSE is not set
CONFIG_INPUT_TOUCHSCREEN=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_SAMSUNG=y
CONFIG_SERIAL_SAMSUNG_CONSOLE=y
CONFIG_HW_RANDOM=y
+CONFIG_I2C_GPIO=y
+CONFIG_POWER_SUPPLY=y
+CONFIG_BATTERY_MAX17040=y
# CONFIG_HWMON is not set
-# CONFIG_USB_SUPPORT is not set
+CONFIG_MFD_MAX8998=y
+CONFIG_REGULATOR=y
+CONFIG_REGULATOR_MAX8998=y
+CONFIG_DRM=y
+CONFIG_DRM_EXYNOS=y
+CONFIG_DRM_EXYNOS_FIMD=y
+CONFIG_DRM_EXYNOS_DPI=y
+CONFIG_USB=y
+CONFIG_USB_OTG=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_EXYNOS=y
+CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_OHCI_EXYNOS=y
+CONFIG_USB_DWC2=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_S3C=y
+CONFIG_MMC_SDHCI_S3C_DMA=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_MAX8998=m
+CONFIG_PHY_SAMSUNG_USB2=m
+CONFIG_PHY_S5PV210_USB2=y
CONFIG_EXT2_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 8/9] ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones
2018-07-06 18:32 ` [PATCH v3 8/9] ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones Paweł Chmiel
@ 2018-07-07 8:49 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:49 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:49PM +0200, Paweł Chmiel wrote:
> Enable config options required for Samsung Aries based phones.
> ARM_APPENDED_DTB is also needed, because stock bootloader
> does not support loading dtb files.
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> arch/arm/configs/s5pv210_defconfig | 33 +++++++++++++++++++++++++++++++--
> 1 file changed, 31 insertions(+), 2 deletions(-)
>
Thanks, applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* [PATCH v3 9/9] ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (7 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 8/9] ARM: s5pv210_defconfig: Enable drivers for Samsung Aries based phones Paweł Chmiel
@ 2018-07-06 18:32 ` Paweł Chmiel
2018-07-07 8:49 ` Krzysztof Kozlowski
2018-07-07 8:52 ` [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Krzysztof Kozlowski
9 siblings, 1 reply; 16+ messages in thread
From: Paweł Chmiel @ 2018-07-06 18:32 UTC (permalink / raw)
To: kgene, krzk, robh+dt, mark.rutland, linux
Cc: linux-arm-kernel, linux-samsung-soc, devicetree, linux-kernel,
xc-racer2, pawel.mikolaj.chmiel
This commit enables few options which are required to boot
typical Linux distro. It was tested by booting ArchLinux ARM
from sdcard.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
arch/arm/configs/s5pv210_defconfig | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/arch/arm/configs/s5pv210_defconfig b/arch/arm/configs/s5pv210_defconfig
index f719e7f9a655..a077597369f1 100644
--- a/arch/arm/configs/s5pv210_defconfig
+++ b/arch/arm/configs/s5pv210_defconfig
@@ -1,5 +1,7 @@
+CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
+CONFIG_CGROUPS=y
CONFIG_SYSFS_DEPRECATED=y
CONFIG_SYSFS_DEPRECATED_V2=y
CONFIG_BLK_DEV_INITRD=y
@@ -18,8 +20,18 @@ CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x20800000,8M console=ttyS
CONFIG_VFP=y
CONFIG_NEON=y
CONFIG_NET=y
+CONFIG_PACKET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
CONFIG_CFG80211=m
+CONFIG_MAC80211=m
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=8192
@@ -63,6 +75,8 @@ CONFIG_RTC_DRV_MAX8998=m
CONFIG_PHY_SAMSUNG_USB2=m
CONFIG_PHY_S5PV210_USB2=y
CONFIG_EXT2_FS=y
+CONFIG_EXT4_FS=y
+CONFIG_AUTOFS4_FS=y
CONFIG_MSDOS_FS=y
CONFIG_VFAT_FS=y
CONFIG_TMPFS=y
@@ -72,6 +86,7 @@ CONFIG_ROMFS_FS=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ASCII=y
CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
CONFIG_DEBUG_INFO=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
--
2.7.4
^ permalink raw reply related [flat|nested] 16+ messages in thread* Re: [PATCH v3 9/9] ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro
2018-07-06 18:32 ` [PATCH v3 9/9] ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro Paweł Chmiel
@ 2018-07-07 8:49 ` Krzysztof Kozlowski
0 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:49 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:50PM +0200, Paweł Chmiel wrote:
> This commit enables few options which are required to boot
> typical Linux distro. It was tested by booting ArchLinux ARM
> from sdcard.
>
> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
> ---
> arch/arm/configs/s5pv210_defconfig | 15 +++++++++++++++
> 1 file changed, 15 insertions(+)
>
Thanks, applied.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G
2018-07-06 18:32 [PATCH v3 0/9] Initial support for Samsung Galaxy S and Galaxy S 4G Paweł Chmiel
` (8 preceding siblings ...)
2018-07-06 18:32 ` [PATCH v3 9/9] ARM: s5pv210_defconfig: Enable options needed to boot typical Linux distro Paweł Chmiel
@ 2018-07-07 8:52 ` Krzysztof Kozlowski
9 siblings, 0 replies; 16+ messages in thread
From: Krzysztof Kozlowski @ 2018-07-07 8:52 UTC (permalink / raw)
To: Paweł Chmiel
Cc: kgene, robh+dt, mark.rutland, linux, linux-arm-kernel,
linux-samsung-soc, devicetree, linux-kernel, xc-racer2
On Fri, Jul 06, 2018 at 08:32:41PM +0200, Paweł Chmiel wrote:
> This patch series adds support for Samsung Galaxy S and Galaxy S 4G.
> Both are commercial phone based on Aries family.
>
> Changes from v2:
> - Restored pinctrl nodes order
> - Correct order of nodes in aries dtsi file
> - Added Reviewed-by to one of patches
> - Added Acked-by to one of patches
> - Squashed two patches updating samsung-boards documentation
I applied first DTS patch and last defconfig. You can resend only the
DTS patches after fixing dtc warnings. Then I'll apply them with the
bindings change.
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 16+ messages in thread