[PATCH 0/3] SOCFPGA Stratix10 SMMU Support

[PATCH 0/3] SOCFPGA Stratix10 SMMU Support

[thor.thayer-VuQAYsv1563Yd54FQh9/CA]

From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>

This patch series adds SMMU support to the SOCFPGA Stratix10 family
of parts. The addition of a clock parameter was required to ungate
the SMMU clock.

Thor Thayer (3):
  Docs: dt: arm-smmu: Add optional clock parameter
  iommu/arm-smmu: Add optional SMMU clock
  arm64: dts: stratix10: Add SMMU Node

 .../devicetree/bindings/iommu/arm,smmu.txt         | 16 ++++++++
 arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi  | 44 ++++++++++++++++++++++
 drivers/iommu/arm-smmu.c                           | 17 +++++++++
 3 files changed, 77 insertions(+)

-- 
2.7.4

[PATCH 1/3] Docs: dt: arm-smmu: Add optional clock parameter

[thor.thayer-VuQAYsv1563Yd54FQh9/CA]

From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>

Add a clock to the SMMU node bindings.

Signed-off-by: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
---
 Documentation/devicetree/bindings/iommu/arm,smmu.txt | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
index 8a6ffce12af5..356fd9f41e1b 100644
--- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt
+++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
@@ -71,6 +71,8 @@ conditions.
                   or using stream matching with #iommu-cells = <2>, and
                   may be ignored if present in such cases.
 
+- clock:          clock provider specifier
+
 ** Deprecated properties:
 
 - mmu-masters (deprecated in favour of the generic "iommus" binding) :
@@ -137,3 +139,17 @@ conditions.
                 iommu-map = <0 &smmu3 0 0x400>;
                 ...
         };
+
+        /* ARM MMU-500 with clock node */
+        smmu4: iommu {
+                compatible = "arm,mmu-500", "arm,smmu-v2";
+                clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
+                ...
+                #iommu-cells = <1>;
+        };
+
+        /* device with stream ID 1 */
+        master4 {
+                iommus = <&smmu4 1>;
+        };
+
-- 
2.7.4

Re: [PATCH 1/3] Docs: dt: arm-smmu: Add optional clock parameter

[Rob Herring]

On Fri, Jul 13, 2018 at 11:27:56AM -0500, thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org wrote:
> From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> 
> Add a clock to the SMMU node bindings.
> 
> Signed-off-by: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/iommu/arm,smmu.txt | 16 ++++++++++++++++
>  1 file changed, 16 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
> index 8a6ffce12af5..356fd9f41e1b 100644
> --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt
> +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
> @@ -71,6 +71,8 @@ conditions.
>                    or using stream matching with #iommu-cells = <2>, and
>                    may be ignored if present in such cases.
>  
> +- clock:          clock provider specifier
> +

The TRM says there is a TCU clock and clock per TBU.

Rob

Re: [PATCH 1/3] Docs: dt: arm-smmu: Add optional clock parameter

[Thor Thayer]

Hi Rob,

On 07/20/2018 11:15 AM, Rob Herring wrote:
> On Fri, Jul 13, 2018 at 11:27:56AM -0500, thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org wrote:
>> From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
>>
>> Add a clock to the SMMU node bindings.
>>
>> Signed-off-by: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
>> ---
>>   Documentation/devicetree/bindings/iommu/arm,smmu.txt | 16 ++++++++++++++++
>>   1 file changed, 16 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/iommu/arm,smmu.txt b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
>> index 8a6ffce12af5..356fd9f41e1b 100644
>> --- a/Documentation/devicetree/bindings/iommu/arm,smmu.txt
>> +++ b/Documentation/devicetree/bindings/iommu/arm,smmu.txt
>> @@ -71,6 +71,8 @@ conditions.
>>                     or using stream matching with #iommu-cells = <2>, and
>>                     may be ignored if present in such cases.
>>   
>> +- clock:          clock provider specifier
>> +
> 
> The TRM says there is a TCU clock and clock per TBU.
> 
> Rob
> 
Yes, good point. I'm abandoning this review and will use the bulk clock 
suggested in [1].

In our case, the TCU clock is always on and we have 1 clock for the
TBU masters.

Thanks for reviewing!

Thor

[1] https://patchwork.kernel.org/patch/10534089/

[PATCH 2/3] iommu/arm-smmu: Add optional SMMU clock

[thor.thayer-VuQAYsv1563Yd54FQh9/CA]

From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>

Add a clock to the SMMU structure. In the device tree case,
check for a clock handle and enable the clock if found.

Signed-off-by: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
---
 drivers/iommu/arm-smmu.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/drivers/iommu/arm-smmu.c b/drivers/iommu/arm-smmu.c
index 69e7c60792a8..0e6dd5019c23 100644
--- a/drivers/iommu/arm-smmu.c
+++ b/drivers/iommu/arm-smmu.c
@@ -212,6 +212,7 @@ struct arm_smmu_device {
 
 	/* IOMMU core code handle */
 	struct iommu_device		iommu;
+	struct clk			*clk;
 };
 
 enum arm_smmu_context_fmt {
@@ -1992,6 +1993,15 @@ static int arm_smmu_device_dt_probe(struct platform_device *pdev,
 	struct device *dev = &pdev->dev;
 	bool legacy_binding;
 
+	/* If a clock is declared, enable it */
+	smmu->clk = devm_clk_get(smmu->dev, NULL);
+	if (IS_ERR(smmu->clk)) {
+		smmu->clk = NULL;
+		dev_dbg(dev, "cannot get smmu clock\n");
+	} else {
+		clk_prepare_enable(smmu->clk);
+	}
+
 	if (of_property_read_u32(dev->of_node, "#global-interrupts",
 				 &smmu->num_global_irqs)) {
 		dev_err(dev, "missing #global-interrupts property\n");
@@ -2181,6 +2191,10 @@ static int arm_smmu_device_remove(struct platform_device *pdev)
 
 	/* Turn the thing off */
 	writel(sCR0_CLIENTPD, ARM_SMMU_GR0_NS(smmu) + ARM_SMMU_GR0_sCR0);
+
+	if (smmu->clk)
+		clk_disable_unprepare(smmu->clk);
+
 	return 0;
 }
 
@@ -2193,6 +2207,9 @@ static int __maybe_unused arm_smmu_pm_resume(struct device *dev)
 {
 	struct arm_smmu_device *smmu = dev_get_drvdata(dev);
 
+	if (smmu->clk)
+		clk_prepare_enable(smmu->clk);
+
 	arm_smmu_device_reset(smmu);
 	return 0;
 }
-- 
2.7.4

[PATCH 3/3] arm64: dts: stratix10: Add SMMU Node

[thor.thayer]

From: Thor Thayer <thor.thayer@linux.intel.com>

Add the SMMU node and IOMMU parameters to the
Stratix10 Device Tree.

Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
---
 arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 44 +++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
index ca67ecb5866e..9b6ead87ae70 100644
--- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
@@ -162,6 +162,8 @@
 			reset-names = "stmmaceth", "stmmaceth-ocp";
 			clocks = <&clkmgr STRATIX10_EMAC0_CLK>;
 			clock-names = "stmmaceth";
+			#stream-id-cells = <1>;
+			iommus = <&smmu 1>;
 			status = "disabled";
 		};
 
@@ -175,6 +177,8 @@
 			reset-names = "stmmaceth", "stmmaceth-ocp";
 			clocks = <&clkmgr STRATIX10_EMAC1_CLK>;
 			clock-names = "stmmaceth";
+			#stream-id-cells = <1>;
+			iommus = <&smmu 2>;
 			status = "disabled";
 		};
 
@@ -188,6 +192,8 @@
 			reset-names = "stmmaceth", "stmmaceth-ocp";
 			clocks = <&clkmgr STRATIX10_EMAC2_CLK>;
 			clock-names = "stmmaceth";
+			#stream-id-cells = <1>;
+			iommus = <&smmu 3>;
 			status = "disabled";
 		};
 
@@ -298,6 +304,8 @@
 			clocks = <&clkmgr STRATIX10_L4_MP_CLK>,
 				 <&clkmgr STRATIX10_SDMMC_CLK>;
 			clock-names = "biu", "ciu";
+			#stream-id-cells = <1>;
+			iommus = <&smmu 5>;
 			status = "disabled";
 		};
 
@@ -323,6 +331,8 @@
 			#dma-requests = <32>;
 			clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
 			clock-names = "apb_pclk";
+			#stream-id-cells = <1>;
+			iommus = <&smmu 8>;
 		};
 
 		rst: rstmgr@ffd11000 {
@@ -332,6 +342,36 @@
 			altr,modrst-offset = <0x20>;
 		};
 
+		smmu: iommu@fa000000 {
+			compatible = "arm,mmu-500", "arm,smmu-v2";
+			reg = <0xfa000000 0x40000>;
+			#global-interrupts = <9>;
+			#iommu-cells = <1>;
+			clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
+			clock-names = "smmu_clk";
+			interrupt-parent = <&intc>;
+			interrupts = <0 128 4>,	/* Global Secure Fault */
+				<0 129 4>, /* Global Non-secure Fault */
+				<0 130 4>, /* FPGA Performance Counter */
+				<0 131 4>, /* DMA Performance Counter */
+				<0 132 4>, /* EMAC Performance Counter */
+				<0 133 4>, /* IO Performance Counter */
+				<0 134 4>, /* SDM Performance Counter */
+				<0 136 4>, /* Non-secure Combined Interrupt */
+				<0 137 4>, /* Secure Combined Interrupt */
+				/* Non-secure Context Interrupts (32) */
+				<0 138 4>, <0 139 4>, <0 140 4>, <0 141 4>,
+				<0 142 4>, <0 143 4>, <0 144 4>, <0 145 4>,
+				<0 146 4>, <0 147 4>, <0 148 4>, <0 149 4>,
+				<0 150 4>, <0 151 4>, <0 152 4>, <0 153 4>,
+				<0 154 4>, <0 155 4>, <0 156 4>, <0 157 4>,
+				<0 158 4>, <0 159 4>, <0 160 4>, <0 161 4>,
+				<0 162 4>, <0 163 4>, <0 164 4>, <0 165 4>,
+				<0 166 4>, <0 167 4>, <0 168 4>, <0 169 4>;
+			stream-match-mask = <0x7ff0>;
+			status = "disabled";
+		};
+
 		spi0: spi@ffda4000 {
 			compatible = "snps,dw-apb-ssi";
 			#address-cells = <1>;
@@ -439,6 +479,8 @@
 			resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>;
 			reset-names = "dwc2", "dwc2-ecc";
 			clocks = <&clkmgr STRATIX10_USB_CLK>;
+			#stream-id-cells = <1>;
+			iommus = <&smmu 6>;
 			status = "disabled";
 		};
 
@@ -451,6 +493,8 @@
 			resets = <&rst USB1_RESET>, <&rst USB1_OCP_RESET>;
 			reset-names = "dwc2", "dwc2-ecc";
 			clocks = <&clkmgr STRATIX10_USB_CLK>;
+			#stream-id-cells = <1>;
+			iommus = <&smmu 7>;
 			status = "disabled";
 		};
 
-- 
2.7.4

Re: [PATCH 3/3] arm64: dts: stratix10: Add SMMU Node

[Robin Murphy]

On 13/07/18 17:27, thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org wrote:
> From: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> 
> Add the SMMU node and IOMMU parameters to the
> Stratix10 Device Tree.
> 
> Signed-off-by: Thor Thayer <thor.thayer-VuQAYsv1563Yd54FQh9/CA@public.gmane.org>
> ---
>   arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 44 +++++++++++++++++++++++
>   1 file changed, 44 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
> index ca67ecb5866e..9b6ead87ae70 100644
> --- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
> +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
> @@ -162,6 +162,8 @@
>   			reset-names = "stmmaceth", "stmmaceth-ocp";
>   			clocks = <&clkmgr STRATIX10_EMAC0_CLK>;
>   			clock-names = "stmmaceth";
> +			#stream-id-cells = <1>;

The #stream-id-cells property is part of the deprecated mmu-masters 
binding, so you don't need to add these.

> +			iommus = <&smmu 1>;
>   			status = "disabled";
>   		};
>   
> @@ -175,6 +177,8 @@
>   			reset-names = "stmmaceth", "stmmaceth-ocp";
>   			clocks = <&clkmgr STRATIX10_EMAC1_CLK>;
>   			clock-names = "stmmaceth";
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 2>;
>   			status = "disabled";
>   		};
>   
> @@ -188,6 +192,8 @@
>   			reset-names = "stmmaceth", "stmmaceth-ocp";
>   			clocks = <&clkmgr STRATIX10_EMAC2_CLK>;
>   			clock-names = "stmmaceth";
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 3>;
>   			status = "disabled";
>   		};
>   
> @@ -298,6 +304,8 @@
>   			clocks = <&clkmgr STRATIX10_L4_MP_CLK>,
>   				 <&clkmgr STRATIX10_SDMMC_CLK>;
>   			clock-names = "biu", "ciu";
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 5>;
>   			status = "disabled";
>   		};
>   
> @@ -323,6 +331,8 @@
>   			#dma-requests = <32>;
>   			clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
>   			clock-names = "apb_pclk";
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 8>;

Just to double-check, all the channel threads and the manager thread 
share the one stream ID? (I'm accustomed to seeing DMA-330 integrated 
with an SMMU by tapping the AxID outputs off to the stream ID input.)

>   		};
>   
>   		rst: rstmgr@ffd11000 {
> @@ -332,6 +342,36 @@
>   			altr,modrst-offset = <0x20>;
>   		};
>   
> +		smmu: iommu@fa000000 {
> +			compatible = "arm,mmu-500", "arm,smmu-v2";
> +			reg = <0xfa000000 0x40000>;
> +			#global-interrupts = <9>;
> +			#iommu-cells = <1>;
> +			clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
> +			clock-names = "smmu_clk";
> +			interrupt-parent = <&intc>;
> +			interrupts = <0 128 4>,	/* Global Secure Fault */
> +				<0 129 4>, /* Global Non-secure Fault */
> +				<0 130 4>, /* FPGA Performance Counter */
> +				<0 131 4>, /* DMA Performance Counter */
> +				<0 132 4>, /* EMAC Performance Counter */
> +				<0 133 4>, /* IO Performance Counter */
> +				<0 134 4>, /* SDM Performance Counter */

Note that there isn't much benefit to adding the secure or PMU 
interrupts here other than to document the hardware - FWIW I have 
actually been working on a PMU driver, and needless to say it turns out 
not to be sufficient just having those munged into the SMMU global fault 
handler.

> +				<0 136 4>, /* Non-secure Combined Interrupt */
> +				<0 137 4>, /* Secure Combined Interrupt */

Similarly the combined interrupt; that's literally just all these other 
interrupt lines ORed together at the SMMU end, and would generally only 
be useful if you *didn't* have the individual lines wired up. As it 
stands with everything listed, any event will also generate a spurious 
global fault IRQ, which isn't ideal (not that you should get many 
interrupts during normal operation, but still...)

Robin.

> +				/* Non-secure Context Interrupts (32) */
> +				<0 138 4>, <0 139 4>, <0 140 4>, <0 141 4>,
> +				<0 142 4>, <0 143 4>, <0 144 4>, <0 145 4>,
> +				<0 146 4>, <0 147 4>, <0 148 4>, <0 149 4>,
> +				<0 150 4>, <0 151 4>, <0 152 4>, <0 153 4>,
> +				<0 154 4>, <0 155 4>, <0 156 4>, <0 157 4>,
> +				<0 158 4>, <0 159 4>, <0 160 4>, <0 161 4>,
> +				<0 162 4>, <0 163 4>, <0 164 4>, <0 165 4>,
> +				<0 166 4>, <0 167 4>, <0 168 4>, <0 169 4>;
> +			stream-match-mask = <0x7ff0>;
> +			status = "disabled";
> +		};
> +
>   		spi0: spi@ffda4000 {
>   			compatible = "snps,dw-apb-ssi";
>   			#address-cells = <1>;
> @@ -439,6 +479,8 @@
>   			resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>;
>   			reset-names = "dwc2", "dwc2-ecc";
>   			clocks = <&clkmgr STRATIX10_USB_CLK>;
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 6>;
>   			status = "disabled";
>   		};
>   
> @@ -451,6 +493,8 @@
>   			resets = <&rst USB1_RESET>, <&rst USB1_OCP_RESET>;
>   			reset-names = "dwc2", "dwc2-ecc";
>   			clocks = <&clkmgr STRATIX10_USB_CLK>;
> +			#stream-id-cells = <1>;
> +			iommus = <&smmu 7>;
>   			status = "disabled";
>   		};
>   
> 

Re: [PATCH 3/3] arm64: dts: stratix10: Add SMMU Node

[Thor Thayer]

Hi Robin,

On 07/13/2018 01:09 PM, Robin Murphy wrote:
> On 13/07/18 17:27, thor.thayer@linux.intel.com wrote:
>> From: Thor Thayer <thor.thayer@linux.intel.com>
>>
>> Add the SMMU node and IOMMU parameters to the
>> Stratix10 Device Tree.
>>
>> Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
>> ---
>>   arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi | 44 
>> +++++++++++++++++++++++
>>   1 file changed, 44 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi 
>> b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
>> index ca67ecb5866e..9b6ead87ae70 100644
>> --- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
>> +++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
>> @@ -162,6 +162,8 @@
>>               reset-names = "stmmaceth", "stmmaceth-ocp";
>>               clocks = <&clkmgr STRATIX10_EMAC0_CLK>;
>>               clock-names = "stmmaceth";
>> +            #stream-id-cells = <1>;
> 
> The #stream-id-cells property is part of the deprecated mmu-masters 
> binding, so you don't need to add these.
> 
OK. Thank you.

>> +            iommus = <&smmu 1>;
>>               status = "disabled";
>>           };

<SNIP>

>>               status = "disabled";
>>           };
>> @@ -323,6 +331,8 @@
>>               #dma-requests = <32>;
>>               clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
>>               clock-names = "apb_pclk";
>> +            #stream-id-cells = <1>;
>> +            iommus = <&smmu 8>;
> 
> Just to double-check, all the channel threads and the manager thread 
> share the one stream ID? (I'm accustomed to seeing DMA-330 integrated 
> with an SMMU by tapping the AxID outputs off to the stream ID input.)
> 
Yes, we have only one stream ID for the DMA. I'll forward the 
differences you noted to our architecture team as something to consider 
for future chips.

>>           };
>>           rst: rstmgr@ffd11000 {
>> @@ -332,6 +342,36 @@
>>               altr,modrst-offset = <0x20>;
>>           };
>> +        smmu: iommu@fa000000 {
>> +            compatible = "arm,mmu-500", "arm,smmu-v2";
>> +            reg = <0xfa000000 0x40000>;
>> +            #global-interrupts = <9>;
>> +            #iommu-cells = <1>;
>> +            clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
>> +            clock-names = "smmu_clk";
>> +            interrupt-parent = <&intc>;
>> +            interrupts = <0 128 4>,    /* Global Secure Fault */
>> +                <0 129 4>, /* Global Non-secure Fault */
>> +                <0 130 4>, /* FPGA Performance Counter */
>> +                <0 131 4>, /* DMA Performance Counter */
>> +                <0 132 4>, /* EMAC Performance Counter */
>> +                <0 133 4>, /* IO Performance Counter */
>> +                <0 134 4>, /* SDM Performance Counter */
> 
> Note that there isn't much benefit to adding the secure or PMU 
> interrupts here other than to document the hardware - FWIW I have 
> actually been working on a PMU driver, and needless to say it turns out 
> not to be sufficient just having those munged into the SMMU global fault 
> handler.
> 
Thanks for pointing this out. I was following other SMMU-500 device 
trees. Just to clarify, how should I simplify this? Should I replace all 
the above with the following?

	<0 129 4>, /* Global Non-secure Fault */

Or will your upcoming PMU driver need the PMU units? It sounded like 
using the just Global fault was not sufficient.

>> +                <0 136 4>, /* Non-secure Combined Interrupt */
>> +                <0 137 4>, /* Secure Combined Interrupt */
> 
> Similarly the combined interrupt; that's literally just all these other 
> interrupt lines ORed together at the SMMU end, and would generally only 
> be useful if you *didn't* have the individual lines wired up. As it 
> stands with everything listed, any event will also generate a spurious 
> global fault IRQ, which isn't ideal (not that you should get many 
> interrupts during normal operation, but still...)
> 
And I'd remove both of these then, right?

Thanks for the review and helpful comments (and also pointing out the 
existing clock patch in my patch series summary)!

Thor

> Robin.
> 
>> +                /* Non-secure Context Interrupts (32) */
>> +                <0 138 4>, <0 139 4>, <0 140 4>, <0 141 4>,
>> +                <0 142 4>, <0 143 4>, <0 144 4>, <0 145 4>,
>> +                <0 146 4>, <0 147 4>, <0 148 4>, <0 149 4>,
>> +                <0 150 4>, <0 151 4>, <0 152 4>, <0 153 4>,
>> +                <0 154 4>, <0 155 4>, <0 156 4>, <0 157 4>,
>> +                <0 158 4>, <0 159 4>, <0 160 4>, <0 161 4>,
>> +                <0 162 4>, <0 163 4>, <0 164 4>, <0 165 4>,
>> +                <0 166 4>, <0 167 4>, <0 168 4>, <0 169 4>;
>> +            stream-match-mask = <0x7ff0>;
>> +            status = "disabled";
>> +        };
>> +
<snip>

_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH 3/3] arm64: dts: stratix10: Add SMMU Node

[Robin Murphy]

On 16/07/18 19:56, Thor Thayer wrote:
[...]
>>> @@ -332,6 +342,36 @@
>>>               altr,modrst-offset = <0x20>;
>>>           };
>>> +        smmu: iommu@fa000000 {
>>> +            compatible = "arm,mmu-500", "arm,smmu-v2";
>>> +            reg = <0xfa000000 0x40000>;
>>> +            #global-interrupts = <9>;
>>> +            #iommu-cells = <1>;
>>> +            clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
>>> +            clock-names = "smmu_clk";
>>> +            interrupt-parent = <&intc>;
>>> +            interrupts = <0 128 4>,    /* Global Secure Fault */
>>> +                <0 129 4>, /* Global Non-secure Fault */
>>> +                <0 130 4>, /* FPGA Performance Counter */
>>> +                <0 131 4>, /* DMA Performance Counter */
>>> +                <0 132 4>, /* EMAC Performance Counter */
>>> +                <0 133 4>, /* IO Performance Counter */
>>> +                <0 134 4>, /* SDM Performance Counter */
>>
>> Note that there isn't much benefit to adding the secure or PMU 
>> interrupts here other than to document the hardware - FWIW I have 
>> actually been working on a PMU driver, and needless to say it turns 
>> out not to be sufficient just having those munged into the SMMU global 
>> fault handler.
>>
> Thanks for pointing this out. I was following other SMMU-500 device 
> trees. Just to clarify, how should I simplify this? Should I replace all 
> the above with the following?
> 
>      <0 129 4>, /* Global Non-secure Fault */
> 
> Or will your upcoming PMU driver need the PMU units? It sounded like 
> using the just Global fault was not sufficient.

No, you had it right - what I meant was it's only worth including the 
actual global fault signals themselves here (there's no harm in leaving 
the secure one in if you like, it just won't do anything if the GIC is 
configured correctly). What I found was that the current SMMU binding 
leaves no reasonable way to encode the PMU interrupts in this interrupt 
list that doesn't break at least one of the possible old/new driver/DT 
combinations, so whatever happens they will need to be specified 
separately once a PMU binding is defined.

>>> +                <0 136 4>, /* Non-secure Combined Interrupt */
>>> +                <0 137 4>, /* Secure Combined Interrupt */
>>
>> Similarly the combined interrupt; that's literally just all these 
>> other interrupt lines ORed together at the SMMU end, and would 
>> generally only be useful if you *didn't* have the individual lines 
>> wired up. As it stands with everything listed, any event will also 
>> generate a spurious global fault IRQ, which isn't ideal (not that you 
>> should get many interrupts during normal operation, but still...)
>>
> And I'd remove both of these then, right?

Indeed.

> Thanks for the review and helpful comments (and also pointing out the 
> existing clock patch in my patch series summary)!

Cheers,
Robin.
_______________________________________________
iommu mailing list
iommu@lists.linux-foundation.org
https://lists.linuxfoundation.org/mailman/listinfo/iommu

Re: [PATCH 0/3] SOCFPGA Stratix10 SMMU Support

[Robin Murphy]

Hi Thor,

On 13/07/18 17:27, thor.thayer@linux.intel.com wrote:
> From: Thor Thayer <thor.thayer@linux.intel.com>
> 
> This patch series adds SMMU support to the SOCFPGA Stratix10 family
> of parts. The addition of a clock parameter was required to ungate
> the SMMU clock.

Please see the latest version of Vivek's runtime PM series[1] - there's 
already been an awful lot of discussion over how to handle clocks, since 
they're not part of the SMMU architecture and different implementations 
can have very different requirements (and even different configurations 
of the same implementation may vary, e.g. MMU-500 could technically have 
up to 33 separate clocks).

Thanks,
Robin.

[1] 
https://www.mail-archive.com/freedreno@lists.freedesktop.org/msg02422.html

> Thor Thayer (3):
>    Docs: dt: arm-smmu: Add optional clock parameter
>    iommu/arm-smmu: Add optional SMMU clock
>    arm64: dts: stratix10: Add SMMU Node
> 
>   .../devicetree/bindings/iommu/arm,smmu.txt         | 16 ++++++++
>   arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi  | 44 ++++++++++++++++++++++
>   drivers/iommu/arm-smmu.c                           | 17 +++++++++
>   3 files changed, 77 insertions(+)
>