From: Aapo Vienamo <avienamo@nvidia.com>
To: Ulf Hansson <ulf.hansson@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Thierry Reding <thierry.reding@gmail.com>,
Jonathan Hunter <jonathanh@nvidia.com>,
Adrian Hunter <adrian.hunter@intel.com>,
Mikko Perttunen <mperttunen@nvidia.com>
Cc: linux-mmc@vger.kernel.org, devicetree@vger.kernel.org,
linux-tegra@vger.kernel.org, linux-kernel@vger.kernel.org,
Aapo Vienamo <avienamo@nvidia.com>
Subject: [PATCH v2 06/10] mmc: tegra: Program pad autocal offsets from dt
Date: Thu, 26 Jul 2018 15:26:52 +0300 [thread overview]
Message-ID: <1532608016-14319-7-git-send-email-avienamo@nvidia.com> (raw)
In-Reply-To: <1532608016-14319-1-git-send-email-avienamo@nvidia.com>
Parse the pad drive strength calibration offsets from the device tree.
Program the calibration offsets in accordance with the current signaling
mode.
Signed-off-by: Aapo Vienamo <avienamo@nvidia.com>
---
drivers/mmc/host/sdhci-tegra.c | 152 ++++++++++++++++++++++++++++++++++++++++-
1 file changed, 151 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 79ecdd0..295ae7a 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -49,6 +49,7 @@
#define SDHCI_TEGRA_AUTO_CAL_CONFIG 0x1e4
#define SDHCI_AUTO_CAL_START BIT(31)
#define SDHCI_AUTO_CAL_ENABLE BIT(29)
+#define SDHCI_AUTO_CAL_PDPU_OFFSET_MASK 0x0000ffff
#define SDHCI_TEGRA_SDMEM_COMP_PADCTRL 0x1e0
#define SDHCI_TEGRA_SDMEM_COMP_PADCTRL_VREF_SEL_MASK 0x0000000f
@@ -72,6 +73,22 @@ struct sdhci_tegra_soc_data {
u32 nvquirks;
};
+/* Magic pull up and pull down pad calibration offsets */
+struct sdhci_tegra_autocal_offsets {
+ u32 pull_up_3v3;
+ u32 pull_down_3v3;
+ u32 pull_up_3v3_timeout;
+ u32 pull_down_3v3_timeout;
+ u32 pull_up_1v8;
+ u32 pull_down_1v8;
+ u32 pull_up_1v8_timeout;
+ u32 pull_down_1v8_timeout;
+ u32 pull_up_sdr104;
+ u32 pull_down_sdr104;
+ u32 pull_up_hs400;
+ u32 pull_down_hs400;
+};
+
struct sdhci_tegra {
const struct sdhci_tegra_soc_data *soc_data;
struct gpio_desc *power_gpio;
@@ -84,6 +101,8 @@ struct sdhci_tegra {
struct pinctrl *pinctrl_sdmmc;
struct pinctrl_state *pinctrl_state_3v3;
struct pinctrl_state *pinctrl_state_1v8;
+
+ struct sdhci_tegra_autocal_offsets autocal_offsets;
};
static u16 tegra_sdhci_readw(struct sdhci_host *host, int reg)
@@ -280,12 +299,45 @@ static bool tegra_sdhci_configure_card_clk(struct sdhci_host *host, bool enable)
return orig_enabled;
}
+static void tegra_sdhci_set_pad_autocal_offset(struct sdhci_host *host,
+ u16 pdpu)
+{
+ u32 reg;
+
+ reg = sdhci_readl(host, SDHCI_TEGRA_AUTO_CAL_CONFIG);
+ reg &= ~SDHCI_AUTO_CAL_PDPU_OFFSET_MASK;
+ reg |= pdpu;
+ sdhci_writel(host, reg, SDHCI_TEGRA_AUTO_CAL_CONFIG);
+}
+
static void tegra_sdhci_pad_autocalib(struct sdhci_host *host)
{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_tegra *tegra_host = sdhci_pltfm_priv(pltfm_host);
+ struct sdhci_tegra_autocal_offsets offsets =
+ tegra_host->autocal_offsets;
+ struct mmc_ios *ios = &host->mmc->ios;
bool card_clk_enabled;
+ u16 pdpu;
u32 reg;
int ret;
+ switch (ios->timing) {
+ case MMC_TIMING_UHS_SDR104:
+ pdpu = offsets.pull_down_sdr104 << 8 | offsets.pull_up_sdr104;
+ break;
+ case MMC_TIMING_MMC_HS400:
+ pdpu = offsets.pull_down_hs400 << 8 | offsets.pull_up_hs400;
+ break;
+ default:
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+ pdpu = offsets.pull_down_1v8 << 8 | offsets.pull_up_1v8;
+ else
+ pdpu = offsets.pull_down_3v3 << 8 | offsets.pull_up_3v3;
+ }
+
+ tegra_sdhci_set_pad_autocal_offset(host, pdpu);
+
card_clk_enabled = tegra_sdhci_configure_card_clk(host, false);
tegra_sdhci_configure_cal_pad(host, true);
@@ -303,8 +355,104 @@ static void tegra_sdhci_pad_autocalib(struct sdhci_host *host)
tegra_sdhci_configure_card_clk(host, card_clk_enabled);
- if (ret)
+ if (ret) {
dev_err(mmc_dev(host->mmc), "Pad autocal timed out\n");
+
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180)
+ pdpu = offsets.pull_down_1v8_timeout << 8 |
+ offsets.pull_up_1v8_timeout;
+ else
+ pdpu = offsets.pull_down_3v3_timeout << 8 |
+ offsets.pull_up_3v3_timeout;
+
+ /* Disable automatic calibration and use fixed offsets */
+ reg = sdhci_readl(host, SDHCI_TEGRA_AUTO_CAL_CONFIG);
+ reg &= ~SDHCI_AUTO_CAL_ENABLE;
+ sdhci_writel(host, reg, SDHCI_TEGRA_AUTO_CAL_CONFIG);
+
+ tegra_sdhci_set_pad_autocal_offset(host, pdpu);
+ }
+}
+
+static void tegra_sdhci_parse_pad_autocal_dt(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_tegra *tegra_host = sdhci_pltfm_priv(pltfm_host);
+ struct sdhci_tegra_autocal_offsets *autocal =
+ &tegra_host->autocal_offsets;
+ int err;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-3v3",
+ &autocal->pull_up_3v3);
+ if (err)
+ autocal->pull_up_3v3 = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-3v3",
+ &autocal->pull_down_3v3);
+ if (err)
+ autocal->pull_down_3v3 = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-1v8",
+ &autocal->pull_up_1v8);
+ if (err)
+ autocal->pull_up_1v8 = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-1v8",
+ &autocal->pull_down_1v8);
+ if (err)
+ autocal->pull_down_1v8 = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-3v3-timeout",
+ &autocal->pull_up_3v3);
+ if (err)
+ autocal->pull_up_3v3_timeout = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-3v3-timeout",
+ &autocal->pull_down_3v3);
+ if (err)
+ autocal->pull_down_3v3_timeout = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-1v8-timeout",
+ &autocal->pull_up_1v8);
+ if (err)
+ autocal->pull_up_1v8_timeout = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-1v8-timeout",
+ &autocal->pull_down_1v8);
+ if (err)
+ autocal->pull_down_1v8_timeout = 0;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-sdr104",
+ &autocal->pull_up_sdr104);
+ if (err)
+ autocal->pull_up_sdr104 = autocal->pull_up_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-sdr104",
+ &autocal->pull_down_sdr104);
+ if (err)
+ autocal->pull_down_sdr104 = autocal->pull_down_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-up-offset-hs400",
+ &autocal->pull_up_hs400);
+ if (err)
+ autocal->pull_up_hs400 = autocal->pull_up_1v8;
+
+ err = device_property_read_u32(host->mmc->parent,
+ "nvidia,pad-autocal-pull-down-offset-hs400",
+ &autocal->pull_down_hs400);
+ if (err)
+ autocal->pull_down_hs400 = autocal->pull_down_1v8;
}
static void tegra_sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
@@ -670,6 +818,8 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
if (tegra_host->soc_data->nvquirks & NVQUIRK_ENABLE_DDR50)
host->mmc->caps |= MMC_CAP_1_8V_DDR;
+ tegra_sdhci_parse_pad_autocal_dt(host);
+
tegra_host->power_gpio = devm_gpiod_get_optional(&pdev->dev, "power",
GPIOD_OUT_HIGH);
if (IS_ERR(tegra_host->power_gpio)) {
--
2.7.4
next prev parent reply other threads:[~2018-07-26 12:26 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-07-26 12:26 [PATCH v2 00/10] Tegra SDHCI update the pad autocal procedure Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 01/10] mmc: tegra: Poll for calibration completion Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 02/10] mmc: tegra: Set calibration pad voltage reference Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 03/10] mmc: tegra: Power on the calibration pad Aapo Vienamo
2018-07-31 9:41 ` Stefan Agner
2018-07-26 12:26 ` [PATCH v2 04/10] mmc: tegra: Disable card clock during pad calibration Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 05/10] dt-bindings: Add Tegra SDHCI pad pdpu offset bindings Aapo Vienamo
2018-07-30 23:31 ` Rob Herring
2018-07-26 12:26 ` Aapo Vienamo [this message]
2018-07-26 12:26 ` [PATCH v2 07/10] arm64: dts: tegra186: Add sdmmc pad auto calibration offsets Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 08/10] arm64: dts: tegra210: " Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 09/10] mmc: tegra: Perform pad calibration after voltage switch Aapo Vienamo
2018-07-26 12:26 ` [PATCH v2 10/10] mmc: tegra: Enable pad calibration on Tegra210 and Tegra186 Aapo Vienamo
2018-07-30 15:07 ` [PATCH v2 00/10] Tegra SDHCI update the pad autocal procedure Ulf Hansson
2018-07-30 15:43 ` Aapo Vienamo
2018-07-31 9:33 ` Stefan Agner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1532608016-14319-7-git-send-email-avienamo@nvidia.com \
--to=avienamo@nvidia.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mperttunen@nvidia.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).