From: Brian Dodge <bdodge09@gmail.com>
To: lee.jones@linaro.org, daniel.thompson@linaro.org,
jingoohan1@gmail.com, jacek.anaszewski@gmail.com, pavel@ucw.cz,
robh+dt@kernel.org, mark.rutland@arm.com,
dri-devel@lists.freedesktop.org, linux-leds@vger.kernel.org,
devicetree@vger.kernel.org
Cc: Brian Dodge <bdodge09@gmail.com>
Subject: [PATCH 1/3] dt-bindings: backlight: fix vendor prefix for ArcticSand arcxcnn driver bindings
Date: Wed, 7 Nov 2018 07:10:38 -0500 [thread overview]
Message-ID: <1541592640-18478-2-git-send-email-bdodge09@gmail.com> (raw)
In-Reply-To: <1541592640-18478-1-git-send-email-bdodge09@gmail.com>
The vendor-prefixes.txt file properly refers to ArcticSand
as arctic but the driver bindings improperly abbreviated the
prefix to arc. This was a mistake in the original patch
Signed-off-by: Brian Dodge <bdodge09@gmail.com>
---
.../bindings/leds/backlight/arcxcnn_bl.txt | 20 ++++++++++----------
1 file changed, 10 insertions(+), 10 deletions(-)
diff --git a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
index 230abde..dcaa239 100644
--- a/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
+++ b/Documentation/devicetree/bindings/leds/backlight/arcxcnn_bl.txt
@@ -1,8 +1,8 @@
-Binding for ArcticSand arc2c0608 LED driver
+Binding for ArcticSand arc family LED drivers
Required properties:
-- compatible: should be "arc,arc2c0608"
-- reg: slave address
+- compatible: "arctic,arc1c0608", "arctic,arc2c0608", "arctic,arc3c0845"
+- reg: slave address
Optional properties:
- default-brightness: brightness value on boot, value from: 0-4095
@@ -11,19 +11,19 @@ Optional properties:
- led-sources: List of enabled channels from 0 to 5.
See Documentation/devicetree/bindings/leds/common.txt
-- arc,led-config-0: setting for register ILED_CONFIG_0
-- arc,led-config-1: setting for register ILED_CONFIG_1
-- arc,dim-freq: PWM mode frequence setting (bits [3:0] used)
-- arc,comp-config: setting for register CONFIG_COMP
-- arc,filter-config: setting for register FILTER_CONFIG
-- arc,trim-config: setting for register IMAXTUNE
+- arctic,led-config-0: setting for register ILED_CONFIG_0
+- arctic,led-config-1: setting for register ILED_CONFIG_1
+- arctic,dim-freq: PWM mode frequence setting (bits [3:0] used)
+- arctic,comp-config: setting for register CONFIG_COMP
+- arctic,filter-config: setting for register FILTER_CONFIG
+- arctic,trim-config: setting for register IMAXTUNE
Note: Optional properties not specified will default to values in IC EPROM
Example:
arc2c0608@30 {
- compatible = "arc,arc2c0608";
+ compatible = "arctic,arc2c0608";
reg = <0x30>;
default-brightness = <500>;
label = "lcd-backlight";
--
2.7.4
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel
next prev parent reply other threads:[~2018-11-07 12:10 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-07 12:10 [PATCH 0/3] backlight/arcxcnn fix vendor prefix in driver and bindings and add support for arc1, arc3 Brian Dodge
2018-11-07 12:10 ` Brian Dodge [this message]
2018-11-12 18:42 ` [PATCH 1/3] dt-bindings: backlight: fix vendor prefix for ArcticSand arcxcnn driver bindings Rob Herring
2018-11-07 12:10 ` [PATCH 2/3] backlight/arcxcnn fix vendor prefix Brian Dodge
2018-11-11 11:30 ` Pavel Machek
2018-11-27 0:44 ` Brian Dodge
2019-06-21 13:39 ` Daniel Thompson
2019-06-21 13:46 ` Daniel Thompson
2019-06-21 13:48 ` Daniel Thompson
2019-06-21 22:13 ` Pavel Machek
2019-06-24 10:24 ` Daniel Thompson
2019-06-24 11:29 ` Brian Dodge
2019-06-24 13:59 ` Daniel Thompson
2018-11-07 12:10 ` [PATCH 3/3] backlight/arcxcnn add support for arc1 an arc3 chip families Brian Dodge
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1541592640-18478-2-git-send-email-bdodge09@gmail.com \
--to=bdodge09@gmail.com \
--cc=daniel.thompson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=jacek.anaszewski@gmail.com \
--cc=jingoohan1@gmail.com \
--cc=lee.jones@linaro.org \
--cc=linux-leds@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).