[PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[Dong Aisheng]

There's a few limitations on the original one cell clock binding
(#clock-cells = <1>) that we have to define some SW clock IDs for device
tree to reference. This may cause troubles if we want to use common
clock IDs for multi platforms support when the clock of those platforms
are mostly the same.
e.g. Current clock IDs name are defined with SS prefix.

However the device may reside in different SS across CPUs, that means the
SS prefix may not valid anymore for a new SoC. Furthermore, the device
availability of those clocks may also vary a bit.

For such situation, we want to eliminate the using of SW Clock IDs and
change to use a more close to HW one instead.
For SCU clocks usage, only two params required: Resource id + Clock Type.
Both parameters are platform independent. So we could use two cells binding
to pass those parameters,

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v3->v4:
 * add some comments for various clock types
v2->v3:
 * Changed to two cells binding and register all clocks in driver
   instead of parse from device tree.
v1->v2:
 * changed to one cell binding inspired by arm,scpi.txt
   Documentation/devicetree/bindings/arm/arm,scpi.txt
   Resource ID is encoded in 'reg' property.
   Clock type is encoded in generic clock-indices property.
   Then we don't have to search all the DT nodes to fetch
   those two value to construct clocks which is relatively
   low efficiency.
 * Add required power-domain property as well.
---
 .../devicetree/bindings/arm/freescale/fsl,scu.txt  | 12 ++++++-----
 include/dt-bindings/firmware/imx/rsrc.h            | 23 ++++++++++++++++++++++
 2 files changed, 30 insertions(+), 5 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
index a575e42..8cee5bf 100644
--- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
+++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
@@ -89,7 +89,10 @@ Required properties:
 			  "fsl,imx8qm-clock"
 			  "fsl,imx8qxp-clock"
 			followed by "fsl,scu-clk"
-- #clock-cells:		Should be 1. Contains the Clock ID value.
+- #clock-cells:		Should be either
+			2: Contains the Resource and Clock ID value.
+			or
+			1: Contains the Clock ID value. (DEPRECATED)
 - clocks:		List of clock specifiers, must contain an entry for
 			each required entry in clock-names
 - clock-names:		Should include entries "xtal_32KHz", "xtal_24MHz"
@@ -184,7 +187,7 @@ firmware {
 
 		clk: clk {
 			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
-			#clock-cells = <1>;
+			#clock-cells = <2>;
 		};
 
 		iomuxc {
@@ -229,8 +232,7 @@ serial@5a060000 {
 	...
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lpuart0>;
-	clocks = <&clk IMX8QXP_UART0_CLK>,
-		 <&clk IMX8QXP_UART0_IPG_CLK>;
-	clock-names = "per", "ipg";
+	clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>;
+	clock-names = "ipg";
 	power-domains = <&pd IMX_SC_R_UART_0>;
 };
diff --git a/include/dt-bindings/firmware/imx/rsrc.h b/include/dt-bindings/firmware/imx/rsrc.h
index 4e61f64..24c153d 100644
--- a/include/dt-bindings/firmware/imx/rsrc.h
+++ b/include/dt-bindings/firmware/imx/rsrc.h
@@ -547,4 +547,27 @@
 #define IMX_SC_R_ATTESTATION		545
 #define IMX_SC_R_LAST			546
 
+/*
+ * Defines for SC PM CLK
+ */
+
+/* Normal device resource clock */
+#define IMX_SC_PM_CLK_SLV_BUS		0	/* Slave bus clock */
+#define IMX_SC_PM_CLK_MST_BUS		1	/* Master bus clock */
+#define IMX_SC_PM_CLK_PER		2	/* Peripheral clock */
+#define IMX_SC_PM_CLK_PHY		3	/* Phy clock */
+#define IMX_SC_PM_CLK_MISC		4	/* Misc clock */
+
+/* Special clock types which do not belong to above normal clock types */
+#define IMX_SC_PM_CLK_MISC0		0	/* Misc 0 clock */
+#define IMX_SC_PM_CLK_MISC1		1	/* Misc 1 clock */
+#define IMX_SC_PM_CLK_MISC2		2	/* Misc 2 clock */
+#define IMX_SC_PM_CLK_MISC3		3	/* Misc 3 clock */
+#define IMX_SC_PM_CLK_MISC4		4	/* Misc 4 clock */
+
+/* Special clock types for CPU/PLL/BYPASS only */
+#define IMX_SC_PM_CLK_CPU		2	/* CPU clock */
+#define IMX_SC_PM_CLK_PLL		4	/* PLL */
+#define IMX_SC_PM_CLK_BYPASS		4	/* Bypass clock */
+
 #endif /* __DT_BINDINGS_RSCRC_IMX_H */
-- 
2.7.4

[PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Dong Aisheng]

MX8QM and MX8QXP LPCG Clocks are mostly the same except they may reside
in different subsystems across CPUs and also vary a bit on the availability.

Same as SCU clock, we want to move the clock definition into device tree
which can fully decouple the dependency of Clock ID definition from device
tree and make us be able to write a fully generic lpcg clock driver.

And we can also use the existence of clock nodes in device tree to address
the device and clock availability differences across different SoCs.

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v3->v4:
 * change bit-offset property to clock-indices
 * use constant macro to define clock indinces
 * drop hw-autogate property which is still not used by drivers
v2->v3:
 * no changes
v1->v2:
 * Update example
 * Add power domain property
---
 .../devicetree/bindings/clock/imx8qxp-lpcg.txt     | 36 ++++++++++++++++++----
 include/dt-bindings/clock/imx8-lpcg.h              | 14 +++++++++
 2 files changed, 44 insertions(+), 6 deletions(-)
 create mode 100644 include/dt-bindings/clock/imx8-lpcg.h

diff --git a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
index 965cfa4..cad8fc4 100644
--- a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
+++ b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
@@ -11,6 +11,21 @@ enabled by these control bits, it might still not be running based
 on the base resource.
 
 Required properties:
+- compatible:		Should be one of:
+			  "fsl,imx8qxp-lpcg"
+			  "fsl,imx8qm-lpcg" followed by "fsl,imx8qxp-lpcg".
+- reg:			Address and length of the register set.
+- #clock-cells:		Should be 1. One LPCG supports multiple clocks.
+- clocks:		Input parent clocks phandle array for each clock.
+- clock-indices:	An integer array indicating the bit offset for each clock.
+			Refer to <include/dt-bindings/clock/imx8-lpcg.h> for the
+			supported LPCG clock indices.
+- clock-output-names:	Shall be the corresponding names of the outputs.
+			NOTE this property must be specified in the same order
+			as the clock-indices property.
+- power-domains:	Should contain the power domain used by this clock.
+
+Legacy binding (DEPRECATED):
 - compatible:	Should be one of:
 		  "fsl,imx8qxp-lpcg-adma",
 		  "fsl,imx8qxp-lpcg-conn",
@@ -33,10 +48,19 @@ Examples:
 
 #include <dt-bindings/clock/imx8qxp-clock.h>
 
-conn_lpcg: clock-controller@5b200000 {
-	compatible = "fsl,imx8qxp-lpcg-conn";
-	reg = <0x5b200000 0xb0000>;
+sdhc0_lpcg: clock-controller@5b200000 {
+	compatible = "fsl,imx8qxp-lpcg";
+	reg = <0x5b200000 0x10000>;
 	#clock-cells = <1>;
+	clocks = <&sdhc0_clk IMX_SC_PM_CLK_PER>,
+		 <&conn_ipg_clk>, <&conn_axi_clk>;
+	clock-indices = <IMX_LPCG_CLK_0>,
+			<IMX_LPCG_CLK_4>,
+			<IMX_LPCG_CLK_5>;
+	clock-output-names = "sdhc0_lpcg_per_clk",
+			     "sdhc0_lpcg_ipg_clk",
+			     "sdhc0_lpcg_ahb_clk";
+	power-domains = <&pd IMX_SC_R_SDHC_0>;
 };
 
 usdhc1: mmc@5b010000 {
@@ -44,8 +68,8 @@ usdhc1: mmc@5b010000 {
 	interrupt-parent = <&gic>;
 	interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
 	reg = <0x5b010000 0x10000>;
-	clocks = <&conn_lpcg IMX8QXP_CONN_LPCG_SDHC0_IPG_CLK>,
-		 <&conn_lpcg IMX8QXP_CONN_LPCG_SDHC0_PER_CLK>,
-		 <&conn_lpcg IMX8QXP_CONN_LPCG_SDHC0_HCLK>;
+	clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>,
+		 <&sdhc0_lpcg IMX_LPCG_CLK_0>,
+		 <&sdhc0_lpcg IMX_LPCG_CLK_5>;
 	clock-names = "ipg", "per", "ahb";
 };
diff --git a/include/dt-bindings/clock/imx8-lpcg.h b/include/dt-bindings/clock/imx8-lpcg.h
new file mode 100644
index 0000000..df90aad
--- /dev/null
+++ b/include/dt-bindings/clock/imx8-lpcg.h
@@ -0,0 +1,14 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Copyright 2019 NXP
+ *   Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+#define IMX_LPCG_CLK_0	0
+#define IMX_LPCG_CLK_1	4
+#define IMX_LPCG_CLK_2	8
+#define IMX_LPCG_CLK_3	12
+#define IMX_LPCG_CLK_4	16
+#define IMX_LPCG_CLK_5	20
+#define IMX_LPCG_CLK_6	24
+#define IMX_LPCG_CLK_7	28
-- 
2.7.4

Re: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[Shawn Guo]

On Tue, Aug 20, 2019 at 07:13:15AM -0400, Dong Aisheng wrote:
> There's a few limitations on the original one cell clock binding
> (#clock-cells = <1>) that we have to define some SW clock IDs for device
> tree to reference. This may cause troubles if we want to use common
> clock IDs for multi platforms support when the clock of those platforms
> are mostly the same.
> e.g. Current clock IDs name are defined with SS prefix.
> 
> However the device may reside in different SS across CPUs, that means the
> SS prefix may not valid anymore for a new SoC. Furthermore, the device
> availability of those clocks may also vary a bit.
> 
> For such situation, we want to eliminate the using of SW Clock IDs and
> change to use a more close to HW one instead.
> For SCU clocks usage, only two params required: Resource id + Clock Type.
> Both parameters are platform independent. So we could use two cells binding
> to pass those parameters,
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>

I'm fine with it.

Acked-by: Shawn Guo <shawnguo@kernel.org>

Shawn

> ---
> ChangeLog:
> v3->v4:
>  * add some comments for various clock types
> v2->v3:
>  * Changed to two cells binding and register all clocks in driver
>    instead of parse from device tree.
> v1->v2:
>  * changed to one cell binding inspired by arm,scpi.txt
>    Documentation/devicetree/bindings/arm/arm,scpi.txt
>    Resource ID is encoded in 'reg' property.
>    Clock type is encoded in generic clock-indices property.
>    Then we don't have to search all the DT nodes to fetch
>    those two value to construct clocks which is relatively
>    low efficiency.
>  * Add required power-domain property as well.
> ---
>  .../devicetree/bindings/arm/freescale/fsl,scu.txt  | 12 ++++++-----
>  include/dt-bindings/firmware/imx/rsrc.h            | 23 ++++++++++++++++++++++
>  2 files changed, 30 insertions(+), 5 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> index a575e42..8cee5bf 100644
> --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> @@ -89,7 +89,10 @@ Required properties:
>  			  "fsl,imx8qm-clock"
>  			  "fsl,imx8qxp-clock"
>  			followed by "fsl,scu-clk"
> -- #clock-cells:		Should be 1. Contains the Clock ID value.
> +- #clock-cells:		Should be either
> +			2: Contains the Resource and Clock ID value.
> +			or
> +			1: Contains the Clock ID value. (DEPRECATED)
>  - clocks:		List of clock specifiers, must contain an entry for
>  			each required entry in clock-names
>  - clock-names:		Should include entries "xtal_32KHz", "xtal_24MHz"
> @@ -184,7 +187,7 @@ firmware {
>  
>  		clk: clk {
>  			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
> -			#clock-cells = <1>;
> +			#clock-cells = <2>;
>  		};
>  
>  		iomuxc {
> @@ -229,8 +232,7 @@ serial@5a060000 {
>  	...
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_lpuart0>;
> -	clocks = <&clk IMX8QXP_UART0_CLK>,
> -		 <&clk IMX8QXP_UART0_IPG_CLK>;
> -	clock-names = "per", "ipg";
> +	clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>;
> +	clock-names = "ipg";
>  	power-domains = <&pd IMX_SC_R_UART_0>;
>  };
> diff --git a/include/dt-bindings/firmware/imx/rsrc.h b/include/dt-bindings/firmware/imx/rsrc.h
> index 4e61f64..24c153d 100644
> --- a/include/dt-bindings/firmware/imx/rsrc.h
> +++ b/include/dt-bindings/firmware/imx/rsrc.h
> @@ -547,4 +547,27 @@
>  #define IMX_SC_R_ATTESTATION		545
>  #define IMX_SC_R_LAST			546
>  
> +/*
> + * Defines for SC PM CLK
> + */
> +
> +/* Normal device resource clock */
> +#define IMX_SC_PM_CLK_SLV_BUS		0	/* Slave bus clock */
> +#define IMX_SC_PM_CLK_MST_BUS		1	/* Master bus clock */
> +#define IMX_SC_PM_CLK_PER		2	/* Peripheral clock */
> +#define IMX_SC_PM_CLK_PHY		3	/* Phy clock */
> +#define IMX_SC_PM_CLK_MISC		4	/* Misc clock */
> +
> +/* Special clock types which do not belong to above normal clock types */
> +#define IMX_SC_PM_CLK_MISC0		0	/* Misc 0 clock */
> +#define IMX_SC_PM_CLK_MISC1		1	/* Misc 1 clock */
> +#define IMX_SC_PM_CLK_MISC2		2	/* Misc 2 clock */
> +#define IMX_SC_PM_CLK_MISC3		3	/* Misc 3 clock */
> +#define IMX_SC_PM_CLK_MISC4		4	/* Misc 4 clock */
> +
> +/* Special clock types for CPU/PLL/BYPASS only */
> +#define IMX_SC_PM_CLK_CPU		2	/* CPU clock */
> +#define IMX_SC_PM_CLK_PLL		4	/* PLL */
> +#define IMX_SC_PM_CLK_BYPASS		4	/* Bypass clock */
> +
>  #endif /* __DT_BINDINGS_RSCRC_IMX_H */
> -- 
> 2.7.4
> 

Re: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Shawn Guo]

On Tue, Aug 20, 2019 at 07:13:16AM -0400, Dong Aisheng wrote:
> MX8QM and MX8QXP LPCG Clocks are mostly the same except they may reside
> in different subsystems across CPUs and also vary a bit on the availability.
> 
> Same as SCU clock, we want to move the clock definition into device tree
> which can fully decouple the dependency of Clock ID definition from device
> tree and make us be able to write a fully generic lpcg clock driver.
> 
> And we can also use the existence of clock nodes in device tree to address
> the device and clock availability differences across different SoCs.
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>

Acked-by: Shawn Guo <shawnguo@kernel.org>

RE: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Aisheng Dong]

Hi Shawn,

> From: Shawn Guo <shawnguo@kernel.org>
> Sent: Sunday, August 25, 2019 3:21 AM
> Subject: Re: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to
> parse clocks from device tree
> 
> On Tue, Aug 20, 2019 at 07:13:16AM -0400, Dong Aisheng wrote:
> > MX8QM and MX8QXP LPCG Clocks are mostly the same except they may
> > reside in different subsystems across CPUs and also vary a bit on the
> availability.
> >
> > Same as SCU clock, we want to move the clock definition into device
> > tree which can fully decouple the dependency of Clock ID definition
> > from device tree and make us be able to write a fully generic lpcg clock
> driver.
> >
> > And we can also use the existence of clock nodes in device tree to
> > address the device and clock availability differences across different SoCs.
> >
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Stephen Boyd <sboyd@kernel.org>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> > Cc: Sascha Hauer <kernel@pengutronix.de>
> > Cc: Michael Turquette <mturquette@baylibre.com>
> > Cc: devicetree@vger.kernel.org
> > Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> 
> Acked-by: Shawn Guo <shawnguo@kernel.org>

Thanks for the review.
Do you think if we have a chance to catch up v5.4?
Will this patch set go through Clock tree or your tree?

Regards
Aisheng

RE: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Aisheng Dong]

> From: Shawn Guo <shawnguo@kernel.org>
> Sent: Sunday, August 25, 2019 3:21 AM
> Subject: Re: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to
> parse clocks from device tree
> 
> On Tue, Aug 20, 2019 at 07:13:16AM -0400, Dong Aisheng wrote:
> > MX8QM and MX8QXP LPCG Clocks are mostly the same except they may
> > reside in different subsystems across CPUs and also vary a bit on the
> availability.
> >
> > Same as SCU clock, we want to move the clock definition into device
> > tree which can fully decouple the dependency of Clock ID definition
> > from device tree and make us be able to write a fully generic lpcg clock
> driver.
> >
> > And we can also use the existence of clock nodes in device tree to
> > address the device and clock availability differences across different SoCs.
> >
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Stephen Boyd <sboyd@kernel.org>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> > Cc: Sascha Hauer <kernel@pengutronix.de>
> > Cc: Michael Turquette <mturquette@baylibre.com>
> > Cc: devicetree@vger.kernel.org
> > Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> 
> Acked-by: Shawn Guo <shawnguo@kernel.org>

Thanks Shawn.

Stephen & Rob,
Would you help review if you're also ok with this binding?
We need this to be finalized early for the following work.

Regards
Aisheng

RE: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[Aisheng Dong]

> From: Shawn Guo <shawnguo@kernel.org>
> Sent: Sunday, August 25, 2019 3:20 AM
> Subject: Re: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to
> parse clocks from device tree
> 
> On Tue, Aug 20, 2019 at 07:13:15AM -0400, Dong Aisheng wrote:
> > There's a few limitations on the original one cell clock binding
> > (#clock-cells = <1>) that we have to define some SW clock IDs for
> > device tree to reference. This may cause troubles if we want to use
> > common clock IDs for multi platforms support when the clock of those
> > platforms are mostly the same.
> > e.g. Current clock IDs name are defined with SS prefix.
> >
> > However the device may reside in different SS across CPUs, that means
> > the SS prefix may not valid anymore for a new SoC. Furthermore, the
> > device availability of those clocks may also vary a bit.
> >
> > For such situation, we want to eliminate the using of SW Clock IDs and
> > change to use a more close to HW one instead.
> > For SCU clocks usage, only two params required: Resource id + Clock Type.
> > Both parameters are platform independent. So we could use two cells
> > binding to pass those parameters,
> >
> > Cc: Rob Herring <robh+dt@kernel.org>
> > Cc: Stephen Boyd <sboyd@kernel.org>
> > Cc: Shawn Guo <shawnguo@kernel.org>
> > Cc: Sascha Hauer <kernel@pengutronix.de>
> > Cc: Michael Turquette <mturquette@baylibre.com>
> > Cc: devicetree@vger.kernel.org
> > Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> 
> I'm fine with it.
> 
> Acked-by: Shawn Guo <shawnguo@kernel.org>
> 

And this one.

Stephen & Rob,
Do you have change to look at it?

We need this to be finalized early for the following work.

Regards
Aisheng


> Shawn
> 
> > ---
> > ChangeLog:
> > v3->v4:
> >  * add some comments for various clock types
> > v2->v3:
> >  * Changed to two cells binding and register all clocks in driver
> >    instead of parse from device tree.
> > v1->v2:
> >  * changed to one cell binding inspired by arm,scpi.txt
> >    Documentation/devicetree/bindings/arm/arm,scpi.txt
> >    Resource ID is encoded in 'reg' property.
> >    Clock type is encoded in generic clock-indices property.
> >    Then we don't have to search all the DT nodes to fetch
> >    those two value to construct clocks which is relatively
> >    low efficiency.
> >  * Add required power-domain property as well.
> > ---
> >  .../devicetree/bindings/arm/freescale/fsl,scu.txt  | 12 ++++++-----
> >  include/dt-bindings/firmware/imx/rsrc.h            | 23
> ++++++++++++++++++++++
> >  2 files changed, 30 insertions(+), 5 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > index a575e42..8cee5bf 100644
> > --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt
> > @@ -89,7 +89,10 @@ Required properties:
> >  			  "fsl,imx8qm-clock"
> >  			  "fsl,imx8qxp-clock"
> >  			followed by "fsl,scu-clk"
> > -- #clock-cells:		Should be 1. Contains the Clock ID value.
> > +- #clock-cells:		Should be either
> > +			2: Contains the Resource and Clock ID value.
> > +			or
> > +			1: Contains the Clock ID value. (DEPRECATED)
> >  - clocks:		List of clock specifiers, must contain an entry for
> >  			each required entry in clock-names
> >  - clock-names:		Should include entries "xtal_32KHz", "xtal_24MHz"
> > @@ -184,7 +187,7 @@ firmware {
> >
> >  		clk: clk {
> >  			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
> > -			#clock-cells = <1>;
> > +			#clock-cells = <2>;
> >  		};
> >
> >  		iomuxc {
> > @@ -229,8 +232,7 @@ serial@5a060000 {
> >  	...
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_lpuart0>;
> > -	clocks = <&clk IMX8QXP_UART0_CLK>,
> > -		 <&clk IMX8QXP_UART0_IPG_CLK>;
> > -	clock-names = "per", "ipg";
> > +	clocks = <&uart0_clk IMX_SC_R_UART_0 IMX_SC_PM_CLK_PER>;
> > +	clock-names = "ipg";
> >  	power-domains = <&pd IMX_SC_R_UART_0>;  }; diff --git
> > a/include/dt-bindings/firmware/imx/rsrc.h
> > b/include/dt-bindings/firmware/imx/rsrc.h
> > index 4e61f64..24c153d 100644
> > --- a/include/dt-bindings/firmware/imx/rsrc.h
> > +++ b/include/dt-bindings/firmware/imx/rsrc.h
> > @@ -547,4 +547,27 @@
> >  #define IMX_SC_R_ATTESTATION		545
> >  #define IMX_SC_R_LAST			546
> >
> > +/*
> > + * Defines for SC PM CLK
> > + */
> > +
> > +/* Normal device resource clock */
> > +#define IMX_SC_PM_CLK_SLV_BUS		0	/* Slave bus clock */
> > +#define IMX_SC_PM_CLK_MST_BUS		1	/* Master bus clock */
> > +#define IMX_SC_PM_CLK_PER		2	/* Peripheral clock */
> > +#define IMX_SC_PM_CLK_PHY		3	/* Phy clock */
> > +#define IMX_SC_PM_CLK_MISC		4	/* Misc clock */
> > +
> > +/* Special clock types which do not belong to above normal clock types */
> > +#define IMX_SC_PM_CLK_MISC0		0	/* Misc 0 clock */
> > +#define IMX_SC_PM_CLK_MISC1		1	/* Misc 1 clock */
> > +#define IMX_SC_PM_CLK_MISC2		2	/* Misc 2 clock */
> > +#define IMX_SC_PM_CLK_MISC3		3	/* Misc 3 clock */
> > +#define IMX_SC_PM_CLK_MISC4		4	/* Misc 4 clock */
> > +
> > +/* Special clock types for CPU/PLL/BYPASS only */
> > +#define IMX_SC_PM_CLK_CPU		2	/* CPU clock */
> > +#define IMX_SC_PM_CLK_PLL		4	/* PLL */
> > +#define IMX_SC_PM_CLK_BYPASS		4	/* Bypass clock */
> > +
> >  #endif /* __DT_BINDINGS_RSCRC_IMX_H */
> > --
> > 2.7.4
> >

Re: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[Rob Herring]

On Tue, 20 Aug 2019 07:13:15 -0400, Dong Aisheng wrote:
> There's a few limitations on the original one cell clock binding
> (#clock-cells = <1>) that we have to define some SW clock IDs for device
> tree to reference. This may cause troubles if we want to use common
> clock IDs for multi platforms support when the clock of those platforms
> are mostly the same.
> e.g. Current clock IDs name are defined with SS prefix.
> 
> However the device may reside in different SS across CPUs, that means the
> SS prefix may not valid anymore for a new SoC. Furthermore, the device
> availability of those clocks may also vary a bit.
> 
> For such situation, we want to eliminate the using of SW Clock IDs and
> change to use a more close to HW one instead.
> For SCU clocks usage, only two params required: Resource id + Clock Type.
> Both parameters are platform independent. So we could use two cells binding
> to pass those parameters,
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> ---
> ChangeLog:
> v3->v4:
>  * add some comments for various clock types
> v2->v3:
>  * Changed to two cells binding and register all clocks in driver
>    instead of parse from device tree.
> v1->v2:
>  * changed to one cell binding inspired by arm,scpi.txt
>    Documentation/devicetree/bindings/arm/arm,scpi.txt
>    Resource ID is encoded in 'reg' property.
>    Clock type is encoded in generic clock-indices property.
>    Then we don't have to search all the DT nodes to fetch
>    those two value to construct clocks which is relatively
>    low efficiency.
>  * Add required power-domain property as well.
> ---
>  .../devicetree/bindings/arm/freescale/fsl,scu.txt  | 12 ++++++-----
>  include/dt-bindings/firmware/imx/rsrc.h            | 23 ++++++++++++++++++++++
>  2 files changed, 30 insertions(+), 5 deletions(-)
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Rob Herring]

On Tue, 20 Aug 2019 07:13:16 -0400, Dong Aisheng wrote:
> MX8QM and MX8QXP LPCG Clocks are mostly the same except they may reside
> in different subsystems across CPUs and also vary a bit on the availability.
> 
> Same as SCU clock, we want to move the clock definition into device tree
> which can fully decouple the dependency of Clock ID definition from device
> tree and make us be able to write a fully generic lpcg clock driver.
> 
> And we can also use the existence of clock nodes in device tree to address
> the device and clock availability differences across different SoCs.
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> ---
> ChangeLog:
> v3->v4:
>  * change bit-offset property to clock-indices
>  * use constant macro to define clock indinces
>  * drop hw-autogate property which is still not used by drivers
> v2->v3:
>  * no changes
> v1->v2:
>  * Update example
>  * Add power domain property
> ---
>  .../devicetree/bindings/clock/imx8qxp-lpcg.txt     | 36 ++++++++++++++++++----
>  include/dt-bindings/clock/imx8-lpcg.h              | 14 +++++++++
>  2 files changed, 44 insertions(+), 6 deletions(-)
>  create mode 100644 include/dt-bindings/clock/imx8-lpcg.h
> 

Reviewed-by: Rob Herring <robh@kernel.org>

Re: [PATCH V4 01/11] dt-bindings: firmware: imx-scu: new binding to parse clocks from device tree

[Stephen Boyd]

Quoting Dong Aisheng (2019-08-20 04:13:15)
> There's a few limitations on the original one cell clock binding
> (#clock-cells = <1>) that we have to define some SW clock IDs for device
> tree to reference. This may cause troubles if we want to use common
> clock IDs for multi platforms support when the clock of those platforms
> are mostly the same.
> e.g. Current clock IDs name are defined with SS prefix.
> 
> However the device may reside in different SS across CPUs, that means the
> SS prefix may not valid anymore for a new SoC. Furthermore, the device
> availability of those clocks may also vary a bit.
> 
> For such situation, we want to eliminate the using of SW Clock IDs and
> change to use a more close to HW one instead.
> For SCU clocks usage, only two params required: Resource id + Clock Type.
> Both parameters are platform independent. So we could use two cells binding
> to pass those parameters,
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> ---

Reviewed-by: Stephen Boyd <sboyd@kernel.org>

Re: [PATCH V4 02/11] dt-bindings: clock: imx-lpcg: add support to parse clocks from device tree

[Stephen Boyd]

Quoting Dong Aisheng (2019-08-20 04:13:16)
> MX8QM and MX8QXP LPCG Clocks are mostly the same except they may reside
> in different subsystems across CPUs and also vary a bit on the availability.
> 
> Same as SCU clock, we want to move the clock definition into device tree
> which can fully decouple the dependency of Clock ID definition from device
> tree and make us be able to write a fully generic lpcg clock driver.
> 
> And we can also use the existence of clock nodes in device tree to address
> the device and clock availability differences across different SoCs.
> 
> Cc: Rob Herring <robh+dt@kernel.org>
> Cc: Stephen Boyd <sboyd@kernel.org>
> Cc: Shawn Guo <shawnguo@kernel.org>
> Cc: Sascha Hauer <kernel@pengutronix.de>
> Cc: Michael Turquette <mturquette@baylibre.com>
> Cc: devicetree@vger.kernel.org
> Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
> ---

Reviewed-by: Stephen Boyd <sboyd@kernel.org>

> ChangeLog:
> v3->v4:
>  * change bit-offset property to clock-indices
>  * use constant macro to define clock indinces
>  * drop hw-autogate property which is still not used by drivers
> v2->v3:
>  * no changes
> v1->v2:
>  * Update example
>  * Add power domain property
> ---
>  .../devicetree/bindings/clock/imx8qxp-lpcg.txt     | 36 ++++++++++++++++++----
>  include/dt-bindings/clock/imx8-lpcg.h              | 14 +++++++++
>  2 files changed, 44 insertions(+), 6 deletions(-)
>  create mode 100644 include/dt-bindings/clock/imx8-lpcg.h
> 
> diff --git a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
> index 965cfa4..cad8fc4 100644
> --- a/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
> +++ b/Documentation/devicetree/bindings/clock/imx8qxp-lpcg.txt
> @@ -11,6 +11,21 @@ enabled by these control bits, it might still not be running based
>  on the base resource.
>  
>  Required properties:
> +- compatible:          Should be one of:
> +                         "fsl,imx8qxp-lpcg"
> +                         "fsl,imx8qm-lpcg" followed by "fsl,imx8qxp-lpcg".
> +- reg:                 Address and length of the register set.
> +- #clock-cells:                Should be 1. One LPCG supports multiple clocks.
> +- clocks:              Input parent clocks phandle array for each clock.
> +- clock-indices:       An integer array indicating the bit offset for each clock.
> +                       Refer to <include/dt-bindings/clock/imx8-lpcg.h> for the
> +                       supported LPCG clock indices.

This is an interesting solution.

> +- clock-output-names:  Shall be the corresponding names of the outputs.
> +                       NOTE this property must be specified in the same order
> +                       as the clock-indices property.
> +- power-domains:       Should contain the power domain used by this clock.
> +
> +Legacy binding (DEPRECATED):
>  - compatible:  Should be one of:
>                   "fsl,imx8qxp-lpcg-adma",
>                   "fsl,imx8qxp-lpcg-conn",