* [PATCH V1 1/2] ARM: dts: qcom: pm6150: Add PM6150/PM6150L PMIC peripherals
[not found] <1570186257-10254-1-git-send-email-kgunda@codeaurora.org>
@ 2019-10-04 10:50 ` Kiran Gunda
2019-10-04 10:50 ` [PATCH V1 2/2] ARM: dts: qcom: sc7180-regulator: Add RPMh regulators for SC7180 Kiran Gunda
1 sibling, 0 replies; 2+ messages in thread
From: Kiran Gunda @ 2019-10-04 10:50 UTC (permalink / raw)
To: bjorn.andersson, Andy Gross, Rob Herring, Mark Rutland,
linux-arm-msm, devicetree, linux-kernel
Cc: Kiran Gunda
Add PM6150/PM6150L peripherals such as PON, GPIOs, ADC and other
PMIC infra modules.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
---
arch/arm64/boot/dts/qcom/pm6150.dtsi | 82 +++++++++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/pm6150l.dtsi | 47 ++++++++++++++++++++
2 files changed, 129 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/pm6150.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/pm6150l.dtsi
diff --git a/arch/arm64/boot/dts/qcom/pm6150.dtsi b/arch/arm64/boot/dts/qcom/pm6150.dtsi
new file mode 100644
index 0000000..c2389866
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6150.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/thermal/thermal.h>
+
+&spmi_bus {
+ pm6150_lsid0: pmic@0 {
+ compatible = "qcom,pm6150", "qcom,spmi-pmic";
+ reg = <0x0 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm6150_pon: pon@800 {
+ compatible = "qcom,pm8998-pon";
+ reg = <0x800>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ linux,code = <KEY_POWER>;
+ };
+ };
+
+ pm6150_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400>;
+ interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm6150_adc ADC5_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm6150_adc: adc@3100 {
+ compatible = "qcom,spmi-adc5";
+ reg = <0x3100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ adc-chan@ADC5_DIE_TEMP {
+ reg = <ADC5_DIE_TEMP>;
+ label = "die_temp";
+ };
+ };
+
+ pm6150_gpio: gpios@c000 {
+ compatible = "qcom,pm6150-gpio", "qcom,spmi-gpio";
+ reg = <0xc000 0xa00>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
+ <0 0xc1 0 IRQ_TYPE_NONE>,
+ <0 0xc2 0 IRQ_TYPE_NONE>,
+ <0 0xc3 0 IRQ_TYPE_NONE>,
+ <0 0xc4 0 IRQ_TYPE_NONE>,
+ <0 0xc5 0 IRQ_TYPE_NONE>,
+ <0 0xc6 0 IRQ_TYPE_NONE>,
+ <0 0xc7 0 IRQ_TYPE_NONE>;
+
+ interrupt-names = "pm6150_gpio1", "pm6150_gpio2",
+ "pm6150_gpio3", "pm6150_gpio4",
+ "pm6150_gpio5", "pm6150_gpio6",
+ "pm6150_gpio7", "pm6150_gpio8";
+ };
+ };
+
+ pm6150_lsid1: pmic@1 {
+ compatible = "qcom,pm6150", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
new file mode 100644
index 0000000..a262092
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+ pm6150l_lsid4: pmic@4 {
+ compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+ reg = <0x4 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm6150l_gpios: gpios@c000 {
+ compatible = "qcom,pm6150l-gpio", "qcom,spmi-gpio";
+ reg = <0xc000 0xc00>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <4 0xc0 0 IRQ_TYPE_NONE>,
+ <4 0xc1 0 IRQ_TYPE_NONE>,
+ <4 0xc2 0 IRQ_TYPE_NONE>,
+ <4 0xc3 0 IRQ_TYPE_NONE>,
+ <4 0xc4 0 IRQ_TYPE_NONE>,
+ <4 0xc5 0 IRQ_TYPE_NONE>,
+ <4 0xc6 0 IRQ_TYPE_NONE>,
+ <4 0xc7 0 IRQ_TYPE_NONE>,
+ <4 0xc8 0 IRQ_TYPE_NONE>,
+ <4 0xc9 0 IRQ_TYPE_NONE>,
+ <4 0xca 0 IRQ_TYPE_NONE>,
+ <4 0xcb 0 IRQ_TYPE_NONE>;
+
+ interrupt-names = "pm6150l_gpio1", "pm6150l_gpio2",
+ "pm6150l_gpio3", "pm6150l_gpio4",
+ "pm6150l_gpio5", "pm6150l_gpio6",
+ "pm6150l_gpio7", "pm6150l_gpio8",
+ "pm6150l_gpio9", "pm6150l_gpio10",
+ "pm6150l_gpio11", "pm6150l_gpio12";
+ };
+ };
+
+ pm6150l_lsid5: pmic@5 {
+ compatible = "qcom,pm6150l", "qcom,spmi-pmic";
+ reg = <0x5 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 2+ messages in thread* [PATCH V1 2/2] ARM: dts: qcom: sc7180-regulator: Add RPMh regulators for SC7180
[not found] <1570186257-10254-1-git-send-email-kgunda@codeaurora.org>
2019-10-04 10:50 ` [PATCH V1 1/2] ARM: dts: qcom: pm6150: Add PM6150/PM6150L PMIC peripherals Kiran Gunda
@ 2019-10-04 10:50 ` Kiran Gunda
1 sibling, 0 replies; 2+ messages in thread
From: Kiran Gunda @ 2019-10-04 10:50 UTC (permalink / raw)
To: bjorn.andersson, Andy Gross, Rob Herring, Mark Rutland,
linux-arm-msm, devicetree, linux-kernel
Cc: Kiran Gunda
Add regulator devices for SC7180 as RPMh regulators. This ensures
that consumers are able to modify the physical state of PMIC
regulators.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
---
arch/arm64/boot/dts/qcom/sc7180-regulator.dtsi | 210 +++++++++++++++++++++++++
1 file changed, 210 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc7180-regulator.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sc7180-regulator.dtsi b/arch/arm64/boot/dts/qcom/sc7180-regulator.dtsi
new file mode 100644
index 0000000..50a675b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-regulator.dtsi
@@ -0,0 +1,210 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2019, The Linux Foundation. All rights reserved.
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+&apps_rsc {
+ pm6150-rpmh-regulators {
+ compatible = "qcom,pm6150-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_s1a_1p1: smps1 {
+ regulator-min-microvolt = <1128000>;
+ regulator-max-microvolt = <1128000>;
+ };
+
+ vreg_s4a_1p0: smps4 {
+ regulator-min-microvolt = <824000>;
+ regulator-max-microvolt = <1120000>;
+ };
+
+ vreg_s5a_2p0: smps5 {
+ regulator-min-microvolt = <1744000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_l1a_1p2: ldo1 {
+ regulator-min-microvolt = <1178000>;
+ regulator-max-microvolt = <1256000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l2a_1p0: ldo2 {
+ regulator-min-microvolt = <944000>;
+ regulator-max-microvolt = <1056000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l3a_1p0: ldo3 {
+ regulator-min-microvolt = <968000>;
+ regulator-max-microvolt = <1064000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l4a_0p8: ldo4 {
+ regulator-min-microvolt = <824000>;
+ regulator-max-microvolt = <928000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l5a_2p7: ldo5 {
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l6a_0p6: ldo6 {
+ regulator-min-microvolt = <568000>;
+ regulator-max-microvolt = <648000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l9a_0p6: ldo9 {
+ regulator-min-microvolt = <488000>;
+ regulator-max-microvolt = <800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l10a_1p8: ldo10 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l11a_1p8: ldo11 {
+ regulator-min-microvolt = <1696000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l12a_1p8: ldo12 {
+ regulator-min-microvolt = <1696000>;
+ regulator-max-microvolt = <1952000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l13a_1p8: ldo13 {
+ regulator-min-microvolt = <1696000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l14a_1p8: ldo14 {
+ regulator-min-microvolt = <1728000>;
+ regulator-max-microvolt = <1832000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l15a_1p8: ldo15 {
+ regulator-min-microvolt = <1696000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l16a_2p7: ldo16 {
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l17a_3p0: ldo17 {
+ regulator-min-microvolt = <2920000>;
+ regulator-max-microvolt = <3232000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l18a_2p8: ldo18 {
+ regulator-min-microvolt = <2496000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l19a_2p9: ldo19 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+ };
+
+ pm6150l-rpmh-regulators {
+ compatible = "qcom,pm6150l-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_s8c_1p3: smps8 {
+ regulator-min-microvolt = <1120000>;
+ regulator-max-microvolt = <1408000>;
+ };
+
+ vreg_l1c_1p8: ldo1 {
+ regulator-min-microvolt = <1616000>;
+ regulator-max-microvolt = <1984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l2c_1p3: ldo2 {
+ regulator-min-microvolt = <1168000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l3c_1p2: ldo3 {
+ regulator-min-microvolt = <1144000>;
+ regulator-max-microvolt = <1304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l4c_1p8: ldo4 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l5c_1p8: ldo5 {
+ regulator-min-microvolt = <1648000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l6c_2p9: ldo6 {
+ regulator-min-microvolt = <2696000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l7c_3p0: ldo7 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3312000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l8c_1p8: ldo8 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l9c_2p9: ldo9 {
+ regulator-min-microvolt = <2952000>;
+ regulator-max-microvolt = <3304000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l10c_3p3: ldo10 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_l11c_3p3: ldo11 {
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3400000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ };
+ };
+};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 2+ messages in thread