From: Anson Huang <Anson.Huang@nxp.com>
To: robh+dt@kernel.org, mark.rutland@arm.com, shawnguo@kernel.org,
s.hauer@pengutronix.de, kernel@pengutronix.de,
festevam@gmail.com, jun.li@nxp.com, daniel.baluta@nxp.com,
ping.bai@nxp.com, leonard.crestez@nxp.com,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org
Cc: Linux-imx@nxp.com
Subject: [PATCH V2 1/3] arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort
Date: Tue, 8 Oct 2019 09:25:53 +0800 [thread overview]
Message-ID: <1570497955-19481-1-git-send-email-Anson.Huang@nxp.com> (raw)
The iomuxc node is being put at end of file because of its huge
pinctrl data. I2C devices should be placed in alphabetical sort.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
---
new patch.
---
arch/arm64/boot/dts/freescale/imx8mm-evk.dts | 124 +++++++++++++--------------
1 file changed, 62 insertions(+), 62 deletions(-)
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index f7a15f3..f6d367c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -94,68 +94,6 @@
};
};
-&sai3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_sai3>;
- assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
- assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
- assigned-clock-rates = <24576000>;
- status = "okay";
-};
-
-&snvs_pwrkey {
- status = "okay";
-};
-
-&uart2 { /* console */
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- status = "okay";
-};
-
-&usbotg1 {
- dr_mode = "otg";
- hnp-disable;
- srp-disable;
- adp-disable;
- usb-role-switch;
- status = "okay";
-
- port {
- usb1_drd_sw: endpoint {
- remote-endpoint = <&typec1_dr_sw>;
- };
- };
-};
-
-&usdhc2 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
- cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
- bus-width = <4>;
- vmmc-supply = <®_usdhc2_vmmc>;
- status = "okay";
-};
-
-&usdhc3 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc3>;
- pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-};
-
-&wdog1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- fsl,ext-reset-output;
- status = "okay";
-};
-
&i2c1 {
clock-frequency = <400000>;
pinctrl-names = "default";
@@ -306,6 +244,68 @@
};
};
+&sai3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sai3>;
+ assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+ assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+ assigned-clock-rates = <24576000>;
+ status = "okay";
+};
+
+&snvs_pwrkey {
+ status = "okay";
+};
+
+&uart2 { /* console */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&usbotg1 {
+ dr_mode = "otg";
+ hnp-disable;
+ srp-disable;
+ adp-disable;
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb1_drd_sw: endpoint {
+ remote-endpoint = <&typec1_dr_sw>;
+ };
+ };
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+ cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ vmmc-supply = <®_usdhc2_vmmc>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
&iomuxc {
pinctrl-names = "default";
--
2.7.4
next reply other threads:[~2019-10-08 1:25 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-08 1:25 Anson Huang [this message]
2019-10-08 1:25 ` [PATCH V2 2/3] arm64: dts: imx8mm-evk: Add i2c3 support Anson Huang
2019-10-08 1:43 ` Fabio Estevam
2019-10-08 1:25 ` [PATCH V2 3/3] arm64: dts: imx8mm-evk: Enable pca6416 on i2c3 bus Anson Huang
2019-10-14 13:16 ` [PATCH V2 1/3] arm64: dts: imx8mm-evk: Adjust i2c nodes following alphabetical sort Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1570497955-19481-1-git-send-email-Anson.Huang@nxp.com \
--to=anson.huang@nxp.com \
--cc=Linux-imx@nxp.com \
--cc=daniel.baluta@nxp.com \
--cc=devicetree@vger.kernel.org \
--cc=festevam@gmail.com \
--cc=jun.li@nxp.com \
--cc=kernel@pengutronix.de \
--cc=leonard.crestez@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=ping.bai@nxp.com \
--cc=robh+dt@kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).