From: Georgii Staroselskii <georgii.staroselskii@emlid.com>
To: mripard@kernel.org, wens@csie.org, robh+dt@kernel.org,
mark.rutland@arm.com
Cc: linux-sunxi@googlegroups.com,
linux-arm-kernel@lists.infradead.org, devicetree@vger.kernel.org,
Georgii Staroselskii <georgii.staroselskii@emlid.com>
Subject: [PATCH 2/2] arm: dts: sunxi: Add Neutis N5H3 support
Date: Wed, 6 Nov 2019 17:03:18 +0300 [thread overview]
Message-ID: <1573048998-8913-3-git-send-email-georgii.staroselskii@emlid.com> (raw)
In-Reply-To: <1573048998-8913-1-git-send-email-georgii.staroselskii@emlid.com>
Emlid Neutis N5H3 is a version of Emlid Neutis SoM with H3 instead of H5
inside.
6eeb4180d4b9 ("ARM: dts: sunxi: h3-h5: Add Bananapi M2+ v1.2 device")
was used as reference.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
---
arch/arm/boot/dts/Makefile | 1 +
.../dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts | 61 ++++++++++++++++++++++
arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi | 11 ++++
3 files changed, 73 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
create mode 100644 arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 3f13b88..c997b0c 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1119,6 +1119,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-h3-orangepi-zero-plus2.dtb \
sun8i-h3-rervision-dvk.dtb \
+ sun8i-h3-emlid-neutis-n5h3-devboard.dtb \
sun8i-r16-bananapi-m2m.dtb \
sun8i-r16-nintendo-nes-classic.dtb \
sun8i-r16-nintendo-super-nes-classic.dtb \
diff --git a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts b/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
new file mode 100644
index 00000000..3b68750
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3-devboard.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTS for Emlid Neutis N5 Dev board.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgiii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3-emlid-neutis-n5h3.dtsi"
+
+/ {
+ model = "Emlid Neutis N5H3 Developer board";
+ compatible = "emlid,neutis-n5h3-devboard",
+ "emlid,neutis-n5h3",
+ "allwinner,sun8i-h3";
+
+ vdd_cpux: gpio-regulator {
+ compatible = "regulator-gpio";
+ regulator-name = "vdd-cpux";
+ regulator-type = "voltage";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-ramp-delay = <50>; /* 4ms */
+ gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
+ gpios-states = <0x1>;
+ states = <1100000 0x0
+ 1300000 0x1>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_cpux>;
+};
+
+&codec {
+ status = "okay";
+};
+
+&emac {
+ phy-handle = <&int_mii_phy>;
+ phy-mode = "mii";
+ allwinner,leds-active-low;
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi b/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
new file mode 100644
index 00000000..eedd5da
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-emlid-neutis-n5h3.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * DTSI for Emlid Neutis N5 SoM.
+ *
+ * Copyright (C) 2019 Georgii Staroselskii <georgii.staroselskii@emlid.com>
+ */
+
+/dts-v1/;
+
+#include "sun8i-h3.dtsi"
+#include <arm/sunxi-h3-h5-emlid-neutis.dtsi>
--
2.7.4
next prev parent reply other threads:[~2019-11-06 14:09 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-11-06 14:03 [PATCH 0/2] Neutis N5H3 support Georgii Staroselskii
2019-11-06 14:03 ` [PATCH 1/2] arm: dts: allwinner: Split out non-SoC specific parts of Neutis N5 Georgii Staroselskii
2019-11-06 14:03 ` Georgii Staroselskii [this message]
2019-11-12 12:15 ` [PATCH 2/2] arm: dts: sunxi: Add Neutis N5H3 support Maxime Ripard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1573048998-8913-3-git-send-email-georgii.staroselskii@emlid.com \
--to=georgii.staroselskii@emlid.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-sunxi@googlegroups.com \
--cc=mark.rutland@arm.com \
--cc=mripard@kernel.org \
--cc=robh+dt@kernel.org \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).