From: Sowjanya Komatineni <skomatineni@nvidia.com>
To: <skomatineni@nvidia.com>, <thierry.reding@gmail.com>,
<jonathanh@nvidia.com>, <frankc@nvidia.com>, <hverkuil@xs4all.nl>,
<sakari.ailus@iki.fi>, <robh+dt@kernel.org>,
<helen.koike@collabora.com>
Cc: <digetx@gmail.com>, <sboyd@kernel.org>,
<gregkh@linuxfoundation.org>, <linux-media@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-tegra@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-i2c@vger.kernel.org>
Subject: [RFC PATCH v3 16/18] gpu: host1x: mipi: Split tegra_mipi_calibrate and tegra_mipi_wait
Date: Tue, 14 Jul 2020 21:20:53 -0700 [thread overview]
Message-ID: <1594786855-26506-17-git-send-email-skomatineni@nvidia.com> (raw)
In-Reply-To: <1594786855-26506-1-git-send-email-skomatineni@nvidia.com>
SW can trigger MIPI pads calibration any time after power on
but calibration results will be latched and applied to the pads
by MIPI CAL unit only when the link is in LP-11 state and then
status register will be updated.
For CSI, trigger of pads calibration happen during CSI stream
enable where CSI receiver is kept ready prior to sensor or CSI
transmitter stream start.
So, pads may not be in LP-11 at this time and waiting for the
calibration to be done immediate after calibration start will
result in timeout.
This patch splits tegra_mipi_calibrate() and tegra_mipi_wait()
so triggering for calibration and waiting for it to complete can
happen at different stages.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
---
drivers/gpu/drm/tegra/dsi.c | 7 ++++++-
drivers/gpu/host1x/mipi.c | 17 +++++++++++++----
include/linux/host1x.h | 1 +
3 files changed, 20 insertions(+), 5 deletions(-)
diff --git a/drivers/gpu/drm/tegra/dsi.c b/drivers/gpu/drm/tegra/dsi.c
index 3c09e29..1a76f1f 100644
--- a/drivers/gpu/drm/tegra/dsi.c
+++ b/drivers/gpu/drm/tegra/dsi.c
@@ -670,6 +670,7 @@ static int tegra_dsi_pad_enable(struct tegra_dsi *dsi)
static int tegra_dsi_pad_calibrate(struct tegra_dsi *dsi)
{
u32 value;
+ int ret;
/*
* XXX Is this still needed? The module reset is deasserted right
@@ -693,7 +694,11 @@ static int tegra_dsi_pad_calibrate(struct tegra_dsi *dsi)
DSI_PAD_PREEMP_PD(0x03) | DSI_PAD_PREEMP_PU(0x3);
tegra_dsi_writel(dsi, value, DSI_PAD_CONTROL_3);
- return tegra_mipi_calibrate(dsi->mipi);
+ ret = tegra_mipi_calibrate(dsi->mipi);
+ if (ret < 0)
+ return ret;
+
+ return tegra_mipi_wait(dsi->mipi);
}
static void tegra_dsi_set_timeout(struct tegra_dsi *dsi, unsigned long bclk,
diff --git a/drivers/gpu/host1x/mipi.c b/drivers/gpu/host1x/mipi.c
index 259e70c..e606464 100644
--- a/drivers/gpu/host1x/mipi.c
+++ b/drivers/gpu/host1x/mipi.c
@@ -293,18 +293,29 @@ int tegra_mipi_disable(struct tegra_mipi_device *dev)
}
EXPORT_SYMBOL(tegra_mipi_disable);
-static int tegra_mipi_wait(struct tegra_mipi *mipi)
+int tegra_mipi_wait(struct tegra_mipi_device *device)
{
+ struct tegra_mipi *mipi = device->mipi;
void __iomem *status_reg = mipi->regs + (MIPI_CAL_STATUS << 2);
u32 value;
int err;
+ err = clk_enable(device->mipi->clk);
+ if (err < 0)
+ return err;
+
+ mutex_lock(&device->mipi->lock);
+
err = readl_relaxed_poll_timeout(status_reg, value,
!(value & MIPI_CAL_STATUS_ACTIVE) &&
(value & MIPI_CAL_STATUS_DONE), 50,
250000);
+ mutex_unlock(&device->mipi->lock);
+ clk_disable(device->mipi->clk);
+
return err;
}
+EXPORT_SYMBOL(tegra_mipi_wait);
int tegra_mipi_calibrate(struct tegra_mipi_device *device)
{
@@ -370,12 +381,10 @@ int tegra_mipi_calibrate(struct tegra_mipi_device *device)
value |= MIPI_CAL_CTRL_START;
tegra_mipi_writel(device->mipi, value, MIPI_CAL_CTRL);
- err = tegra_mipi_wait(device->mipi);
-
mutex_unlock(&device->mipi->lock);
clk_disable(device->mipi->clk);
- return err;
+ return 0;
}
EXPORT_SYMBOL(tegra_mipi_calibrate);
diff --git a/include/linux/host1x.h b/include/linux/host1x.h
index 9e67841..20c885d 100644
--- a/include/linux/host1x.h
+++ b/include/linux/host1x.h
@@ -334,5 +334,6 @@ void tegra_mipi_free(struct tegra_mipi_device *device);
int tegra_mipi_enable(struct tegra_mipi_device *device);
int tegra_mipi_disable(struct tegra_mipi_device *device);
int tegra_mipi_calibrate(struct tegra_mipi_device *device);
+int tegra_mipi_wait(struct tegra_mipi_device *device);
#endif
--
2.7.4
next prev parent reply other threads:[~2020-07-15 4:20 UTC|newest]
Thread overview: 44+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-15 4:20 [RFC PATCH v3 00/18] Support for Tegra video capture from external sensor Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 01/18] dt-bindings: i2c: tegra: Document Tegra210 VI I2C clocks and power-domains Sowjanya Komatineni
2020-07-16 13:25 ` Thierry Reding
2020-07-15 4:20 ` [RFC PATCH v3 02/18] arm64: tegra: Add missing clocks and power-domains to Tegra210 VI I2C Sowjanya Komatineni
2020-07-16 13:25 ` Thierry Reding
2020-07-15 4:20 ` [RFC PATCH v3 03/18] i2c: tegra: Don't mark VI I2C as IRQ safe runtime PM Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 04/18] i2c: tegra: Remove NULL pointer check before clk_enable/disable/prepare/unprepare Sowjanya Komatineni
2020-07-16 20:25 ` Dmitry Osipenko
2020-07-15 4:20 ` [RFC PATCH v3 05/18] i2c: tegra: Fix the error path in tegra_i2c_runtime_resume Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 06/18] i2c: tegra: Fix runtime resume to re-init VI I2C Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 07/18] i2c: tegra: Avoid tegra_i2c_init_dma() for Tegra210 vi i2c Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 08/18] media: tegra-video: Fix channel format alignment Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 09/18] media: tegra-video: Enable TPG based on kernel config Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 10/18] media: tegra-video: Update format lookup to offset based Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 11/18] dt-bindings: tegra: Update VI and CSI bindings with port info Sowjanya Komatineni
2020-07-16 19:09 ` Rob Herring
2020-07-15 4:20 ` [RFC PATCH v3 12/18] media: tegra-video: Add support for external sensor capture Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 13/18] media: tegra-video: Add support for selection ioctl ops Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 14/18] gpu: host1x: mipi: Update tegra_mipi_request() to be node based Sowjanya Komatineni
2020-07-16 20:26 ` Dmitry Osipenko
2020-07-15 4:20 ` [RFC PATCH v3 15/18] gpu: host1x: mipi: Use readl_relaxed_poll_timeout in tegra_mipi_wait Sowjanya Komatineni
2020-07-15 4:20 ` Sowjanya Komatineni [this message]
2020-07-16 20:38 ` [RFC PATCH v3 16/18] gpu: host1x: mipi: Split tegra_mipi_calibrate and tegra_mipi_wait Dmitry Osipenko
2020-07-16 21:09 ` Sowjanya Komatineni
2020-07-16 21:18 ` Dmitry Osipenko
2020-07-16 22:49 ` Sowjanya Komatineni
2020-07-16 23:01 ` Dmitry Osipenko
2020-07-16 23:06 ` Sowjanya Komatineni
2020-07-16 23:09 ` Sowjanya Komatineni
2020-07-16 23:47 ` Dmitry Osipenko
2020-07-17 0:16 ` Sowjanya Komatineni
2020-07-17 4:46 ` Sowjanya Komatineni
2020-07-17 15:01 ` Dmitry Osipenko
2020-07-17 15:41 ` Sowjanya Komatineni
2020-07-17 20:14 ` Dmitry Osipenko
2020-07-15 4:20 ` [RFC PATCH v3 17/18] media: tegra-video: Add CSI MIPI pads calibration Sowjanya Komatineni
2020-07-15 4:20 ` [RFC PATCH v3 18/18] media: tegra-video: Compute settle times based on the clock rate Sowjanya Komatineni
2020-07-17 10:54 ` [RFC PATCH v3 00/18] Support for Tegra video capture from external sensor Hans Verkuil
2020-07-17 16:34 ` Sowjanya Komatineni
2020-07-17 17:08 ` Hans Verkuil
2020-07-17 17:23 ` Sowjanya Komatineni
2020-07-17 17:38 ` Sowjanya Komatineni
2020-07-17 17:48 ` Sowjanya Komatineni
2020-07-20 4:41 ` Sowjanya Komatineni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1594786855-26506-17-git-send-email-skomatineni@nvidia.com \
--to=skomatineni@nvidia.com \
--cc=devicetree@vger.kernel.org \
--cc=digetx@gmail.com \
--cc=frankc@nvidia.com \
--cc=gregkh@linuxfoundation.org \
--cc=helen.koike@collabora.com \
--cc=hverkuil@xs4all.nl \
--cc=jonathanh@nvidia.com \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=sakari.ailus@iki.fi \
--cc=sboyd@kernel.org \
--cc=thierry.reding@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).