From: Sowjanya Komatineni <skomatineni@nvidia.com>
To: <adrian.hunter@intel.com>, <ulf.hansson@linaro.org>,
<thierry.reding@gmail.com>, <jonathanh@nvidia.com>,
<robh+dt@kernel.org>
Cc: <skomatineni@nvidia.com>, <linux-tegra@vger.kernel.org>,
<linux-kernel@vger.kernel.org>, <linux-mmc@vger.kernel.org>,
<devicetree@vger.kernel.org>, <stable@vger.kernel.org>
Subject: [PATCH v6 7/7] sdhci: tegra: Add missing TMCLK for data timeout
Date: Wed, 26 Aug 2020 20:50:01 -0700 [thread overview]
Message-ID: <1598500201-5987-8-git-send-email-skomatineni@nvidia.com> (raw)
In-Reply-To: <1598500201-5987-1-git-send-email-skomatineni@nvidia.com>
commit b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Tegra210 and later has a separate sdmmc_legacy_tm (TMCLK) used by Tegra
SDMMC hawdware for data timeout to achive better timeout than using
SDCLK and using TMCLK is recommended.
USE_TMCLK_FOR_DATA_TIMEOUT bit in Tegra SDMMC register
SDHCI_TEGRA_VENDOR_SYS_SW_CTRL can be used to choose either TMCLK or
SDCLK for data timeout.
Default USE_TMCLK_FOR_DATA_TIMEOUT bit is set to 1 and TMCLK is used
for data timeout by Tegra SDMMC hardware and having TMCLK not enabled
is not recommended.
So, this patch adds quirk NVQUIRK_HAS_TMCLK for SoC having separate
timeout clock and keeps TMCLK enabled all the time.
Fixes: b5a84ecf025a ("mmc: tegra: Add Tegra210 support")
Cc: stable <stable@vger.kernel.org> # 5.4
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
---
drivers/mmc/host/sdhci-tegra.c | 90 ++++++++++++++++++++++++++++++++++++++----
1 file changed, 82 insertions(+), 8 deletions(-)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 31ed321..f69ca8d 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -13,6 +13,7 @@
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/of.h>
+#include <linux/of_clk.h>
#include <linux/of_device.h>
#include <linux/pinctrl/consumer.h>
#include <linux/regulator/consumer.h>
@@ -110,6 +111,12 @@
#define NVQUIRK_DIS_CARD_CLK_CONFIG_TAP BIT(8)
#define NVQUIRK_CQHCI_DCMD_R1B_CMD_TIMING BIT(9)
+/*
+ * NVQUIRK_HAS_TMCLK is for SoC's having separate timeout clock for Tegra
+ * SDMMC hardware data timeout.
+ */
+#define NVQUIRK_HAS_TMCLK BIT(10)
+
/* SDMMC CQE Base Address for Tegra Host Ver 4.1 and Higher */
#define SDHCI_TEGRA_CQE_BASE_ADDR 0xF000
@@ -140,6 +147,7 @@ struct sdhci_tegra_autocal_offsets {
struct sdhci_tegra {
const struct sdhci_tegra_soc_data *soc_data;
struct gpio_desc *power_gpio;
+ struct clk *tmclk;
bool ddr_signaling;
bool pad_calib_required;
bool pad_control_available;
@@ -1433,7 +1441,8 @@ static const struct sdhci_tegra_soc_data soc_data_tegra210 = {
NVQUIRK_HAS_PADCALIB |
NVQUIRK_DIS_CARD_CLK_CONFIG_TAP |
NVQUIRK_ENABLE_SDR50 |
- NVQUIRK_ENABLE_SDR104,
+ NVQUIRK_ENABLE_SDR104 |
+ NVQUIRK_HAS_TMCLK,
.min_tap_delay = 106,
.max_tap_delay = 185,
};
@@ -1471,6 +1480,7 @@ static const struct sdhci_tegra_soc_data soc_data_tegra186 = {
NVQUIRK_DIS_CARD_CLK_CONFIG_TAP |
NVQUIRK_ENABLE_SDR50 |
NVQUIRK_ENABLE_SDR104 |
+ NVQUIRK_HAS_TMCLK |
NVQUIRK_CQHCI_DCMD_R1B_CMD_TIMING,
.min_tap_delay = 84,
.max_tap_delay = 136,
@@ -1483,7 +1493,8 @@ static const struct sdhci_tegra_soc_data soc_data_tegra194 = {
NVQUIRK_HAS_PADCALIB |
NVQUIRK_DIS_CARD_CLK_CONFIG_TAP |
NVQUIRK_ENABLE_SDR50 |
- NVQUIRK_ENABLE_SDR104,
+ NVQUIRK_ENABLE_SDR104 |
+ NVQUIRK_HAS_TMCLK,
.min_tap_delay = 96,
.max_tap_delay = 139,
};
@@ -1611,15 +1622,76 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
goto err_power_req;
}
- clk = devm_clk_get(mmc_dev(host->mmc), NULL);
- if (IS_ERR(clk)) {
- rc = PTR_ERR(clk);
+ /*
+ * Tegra210 and later has separate SDMMC_LEGACY_TM clock used for
+ * hardware data timeout clock and SW can choose TMCLK or SDCLK for
+ * hardware data timeout through the bit USE_TMCLK_FOR_DATA_TIMEOUT
+ * of the register SDHCI_TEGRA_VENDOR_SYS_SW_CTRL.
+ *
+ * USE_TMCLK_FOR_DATA_TIMEOUT bit default is set to 1 and SDMMC uses
+ * 12Mhz TMCLK which is advertised in host capability register.
+ * With TMCLK of 12Mhz provides maximum data timeout period that can
+ * be achieved is 11s better than using SDCLK for data timeout.
+ *
+ * So, TMCLK is set to 12Mhz and kept enabled all the time on SoC's
+ * supporting separate TMCLK.
+ *
+ * Old device tree has single sdhci clock. So with addition of TMCLK,
+ * retrieving sdhci clock by "sdhci" clock name based on number of
+ * clocks in sdhci device node.
+ */
+
+ if (of_clk_get_parent_count(pdev->dev.of_node) == 1) {
+ if (soc_data->nvquirks & NVQUIRK_HAS_TMCLK)
+ dev_warn(&pdev->dev,
+ "missing tmclk in the device tree\n");
+
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk)) {
+ rc = PTR_ERR(clk);
- if (rc != -EPROBE_DEFER)
- dev_err(&pdev->dev, "failed to get clock: %d\n", rc);
+ if (rc != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "failed to get sdhci clock: %d\n", rc);
- goto err_clk_get;
+ goto err_power_req;
+ }
+ } else {
+ if (soc_data->nvquirks & NVQUIRK_HAS_TMCLK) {
+ clk = devm_clk_get(&pdev->dev, "tmclk");
+ if (IS_ERR(clk)) {
+ rc = PTR_ERR(clk);
+ if (rc == -EPROBE_DEFER)
+ goto err_power_req;
+
+ dev_warn(&pdev->dev,
+ "failed to get tmclk: %d\n", rc);
+ clk = NULL;
+ }
+
+ clk_set_rate(clk, 12000000);
+ rc = clk_prepare_enable(clk);
+ if (rc) {
+ dev_err(&pdev->dev,
+ "failed to enable tmclk: %d\n", rc);
+ goto err_power_req;
+ }
+
+ tegra_host->tmclk = clk;
+ }
+
+ clk = devm_clk_get(&pdev->dev, "sdhci");
+ if (IS_ERR(clk)) {
+ rc = PTR_ERR(clk);
+
+ if (rc != -EPROBE_DEFER)
+ dev_err(&pdev->dev,
+ "failed to get sdhci clock: %d\n", rc);
+
+ goto err_clk_get;
+ }
}
+
clk_prepare_enable(clk);
pltfm_host->clk = clk;
@@ -1654,6 +1726,7 @@ static int sdhci_tegra_probe(struct platform_device *pdev)
err_rst_get:
clk_disable_unprepare(pltfm_host->clk);
err_clk_get:
+ clk_disable_unprepare(tegra_host->tmclk);
err_power_req:
err_parse_dt:
sdhci_pltfm_free(pdev);
@@ -1671,6 +1744,7 @@ static int sdhci_tegra_remove(struct platform_device *pdev)
reset_control_assert(tegra_host->rst);
usleep_range(2000, 4000);
clk_disable_unprepare(pltfm_host->clk);
+ clk_disable_unprepare(tegra_host->tmclk);
sdhci_pltfm_free(pdev);
--
2.7.4
next prev parent reply other threads:[~2020-08-27 3:50 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-27 3:49 [PATCH v6 0/7] Fix timeout clock used by hardware data timeout Sowjanya Komatineni
2020-08-27 3:49 ` [PATCH v6 1/7] sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra210 Sowjanya Komatineni
2020-08-27 3:49 ` [PATCH v6 2/7] sdhci: tegra: Remove SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK for Tegra186 Sowjanya Komatineni
2020-08-27 3:49 ` [PATCH v6 3/7] dt-bindings: mmc: tegra: Add tmclk for Tegra210 and later Sowjanya Komatineni
2020-08-27 8:53 ` Jon Hunter
2020-08-27 3:49 ` [PATCH v6 4/7] arm64: tegra: Add missing timeout clock to Tegra210 SDMMC Sowjanya Komatineni
2020-08-27 3:49 ` [PATCH v6 5/7] arm64: tegra: Add missing timeout clock to Tegra186 SDMMC nodes Sowjanya Komatineni
2020-08-27 3:50 ` [PATCH v6 6/7] arm64: tegra: Add missing timeout clock to Tegra194 " Sowjanya Komatineni
2020-08-27 3:50 ` Sowjanya Komatineni [this message]
2020-08-27 8:40 ` [PATCH v6 7/7] sdhci: tegra: Add missing TMCLK for data timeout Jon Hunter
2020-08-27 15:03 ` Sowjanya Komatineni
2020-08-27 15:14 ` Jon Hunter
2020-08-27 15:43 ` Sowjanya Komatineni
2020-08-27 15:51 ` Jon Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1598500201-5987-8-git-send-email-skomatineni@nvidia.com \
--to=skomatineni@nvidia.com \
--cc=adrian.hunter@intel.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mmc@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=stable@vger.kernel.org \
--cc=thierry.reding@gmail.com \
--cc=ulf.hansson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).