From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <mturquette@baylibre.com>, <sboyd@kernel.org>,
<nicolas.ferre@microchip.com>, <alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <robh+dt@kernel.org>
Cc: <eugen.hristev@microchip.com>, <linux-clk@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
Claudiu Beznea <claudiu.beznea@microchip.com>
Subject: [PATCH v3 09/11] clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
Date: Fri, 6 Nov 2020 11:28:02 +0200 [thread overview]
Message-ID: <1604654884-30339-10-git-send-email-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <1604654884-30339-1-git-send-email-claudiu.beznea@microchip.com>
Since CPU PLL feeds both CPU clock and MCK0, MCK0 cannot go higher
than 200MHz and MCK0 maximum prescaller is 5 limit the CPU PLL at
1GHz to avoid MCK0 overclocking while CPU PLL is changed by DVFS.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
drivers/clk/at91/sama7g5.c | 61 +++++++++++++++++++++++++++++++++++-----------
1 file changed, 47 insertions(+), 14 deletions(-)
diff --git a/drivers/clk/at91/sama7g5.c b/drivers/clk/at91/sama7g5.c
index 662e667d1098..3924f256da67 100644
--- a/drivers/clk/at91/sama7g5.c
+++ b/drivers/clk/at91/sama7g5.c
@@ -89,11 +89,40 @@ static const struct clk_pll_layout pll_layout_divio = {
.endiv_shift = 30,
};
+/*
+ * CPU PLL output range.
+ * Notice: The upper limit has been setup to 1000000002 due to hardware
+ * block which cannot output exactly 1GHz.
+ */
+static const struct clk_range cpu_pll_outputs[] = {
+ { .min = 2343750, .max = 1000000002 },
+};
+
+/* PLL output range. */
+static const struct clk_range pll_outputs[] = {
+ { .min = 2343750, .max = 1200000000 },
+};
+
+/* CPU PLL characteristics. */
+static const struct clk_pll_characteristics cpu_pll_characteristics = {
+ .input = { .min = 12000000, .max = 50000000 },
+ .num_output = ARRAY_SIZE(cpu_pll_outputs),
+ .output = cpu_pll_outputs,
+};
+
+/* PLL characteristics. */
+static const struct clk_pll_characteristics pll_characteristics = {
+ .input = { .min = 12000000, .max = 50000000 },
+ .num_output = ARRAY_SIZE(pll_outputs),
+ .output = pll_outputs,
+};
+
/**
* PLL clocks description
* @n: clock name
* @p: clock parent
* @l: clock layout
+ * @c: clock characteristics
* @t: clock type
* @f: clock flags
* @eid: export index in sama7g5->chws[] array
@@ -102,6 +131,7 @@ static const struct {
const char *n;
const char *p;
const struct clk_pll_layout *l;
+ const struct clk_pll_characteristics *c;
u32 f;
u8 t;
u8 eid;
@@ -110,12 +140,14 @@ static const struct {
{ .n = "cpupll_fracck",
.p = "mainck",
.l = &pll_layout_frac,
+ .c = &cpu_pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_IS_CRITICAL, },
{ .n = "cpupll_divpmcck",
.p = "cpupll_fracck",
.l = &pll_layout_divpmc,
+ .c = &cpu_pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_IS_CRITICAL | CLK_SET_RATE_PARENT,
.eid = PMC_CPUPLL, },
@@ -125,12 +157,14 @@ static const struct {
{ .n = "syspll_fracck",
.p = "mainck",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_IS_CRITICAL | CLK_SET_RATE_GATE, },
{ .n = "syspll_divpmcck",
.p = "syspll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_IS_CRITICAL | CLK_SET_RATE_GATE,
.eid = PMC_SYSPLL, },
@@ -140,12 +174,14 @@ static const struct {
{ .n = "ddrpll_fracck",
.p = "mainck",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_IS_CRITICAL | CLK_SET_RATE_GATE, },
{ .n = "ddrpll_divpmcck",
.p = "ddrpll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_IS_CRITICAL | CLK_SET_RATE_GATE, },
},
@@ -154,12 +190,14 @@ static const struct {
{ .n = "imgpll_fracck",
.p = "mainck",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_SET_RATE_GATE, },
{ .n = "imgpll_divpmcck",
.p = "imgpll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE |
CLK_SET_RATE_PARENT, },
@@ -169,12 +207,14 @@ static const struct {
{ .n = "baudpll_fracck",
.p = "mainck",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_SET_RATE_GATE, },
{ .n = "baudpll_divpmcck",
.p = "baudpll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE |
CLK_SET_RATE_PARENT, },
@@ -184,12 +224,14 @@ static const struct {
{ .n = "audiopll_fracck",
.p = "main_xtal",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_SET_RATE_GATE, },
{ .n = "audiopll_divpmcck",
.p = "audiopll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE |
CLK_SET_RATE_PARENT,
@@ -198,6 +240,7 @@ static const struct {
{ .n = "audiopll_diviock",
.p = "audiopll_fracck",
.l = &pll_layout_divio,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE |
CLK_SET_RATE_PARENT,
@@ -208,12 +251,14 @@ static const struct {
{ .n = "ethpll_fracck",
.p = "main_xtal",
.l = &pll_layout_frac,
+ .c = &pll_characteristics,
.t = PLL_TYPE_FRAC,
.f = CLK_SET_RATE_GATE, },
{ .n = "ethpll_divpmcck",
.p = "ethpll_fracck",
.l = &pll_layout_divpmc,
+ .c = &pll_characteristics,
.t = PLL_TYPE_DIV,
.f = CLK_SET_RATE_GATE | CLK_SET_PARENT_GATE |
CLK_SET_RATE_PARENT, },
@@ -774,18 +819,6 @@ static const struct {
.pp_chg_id = INT_MIN, },
};
-/* PLL output range. */
-static const struct clk_range pll_outputs[] = {
- { .min = 2343750, .max = 1200000000 },
-};
-
-/* PLL characteristics. */
-static const struct clk_pll_characteristics pll_characteristics = {
- .input = { .min = 12000000, .max = 50000000 },
- .num_output = ARRAY_SIZE(pll_outputs),
- .output = pll_outputs,
-};
-
/* MCK0 characteristics. */
static const struct clk_master_characteristics mck0_characteristics = {
.output = { .min = 50000000, .max = 200000000 },
@@ -902,7 +935,7 @@ static void __init sama7g5_pmc_setup(struct device_node *np)
hw = sam9x60_clk_register_frac_pll(regmap,
&pmc_pll_lock, sama7g5_plls[i][j].n,
sama7g5_plls[i][j].p, parent_hw, i,
- &pll_characteristics,
+ sama7g5_plls[i][j].c,
sama7g5_plls[i][j].l,
sama7g5_plls[i][j].f);
break;
@@ -911,7 +944,7 @@ static void __init sama7g5_pmc_setup(struct device_node *np)
hw = sam9x60_clk_register_div_pll(regmap,
&pmc_pll_lock, sama7g5_plls[i][j].n,
sama7g5_plls[i][j].p, i,
- &pll_characteristics,
+ sama7g5_plls[i][j].c,
sama7g5_plls[i][j].l,
sama7g5_plls[i][j].f);
break;
--
2.7.4
next prev parent reply other threads:[~2020-11-06 9:29 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-06 9:27 [PATCH v3 00/11] clk: at91: adapt for dvfs Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 01/11] clk: at91: sama7g5: fix compilation error Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 02/11] dt-bindings: clock: at91: add sama7g5 pll defines Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 03/11] clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 04/11] clk: at91: clk-master: add 5th divisor for mck master Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 05/11] clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics Claudiu Beznea
2020-11-06 9:27 ` [PATCH v3 06/11] clk: at91: clk-sam9x60-pll: allow runtime changes for pll Claudiu Beznea
2020-11-06 9:28 ` [PATCH v3 07/11] clk: at91: sama7g5: remove mck0 from parent list of other clocks Claudiu Beznea
2020-11-06 9:28 ` [PATCH v3 08/11] clk: at91: sama7g5: decrease lower limit for MCK0 rate Claudiu Beznea
2020-11-06 9:28 ` Claudiu Beznea [this message]
2020-11-06 9:28 ` [PATCH v3 10/11] clk: at91: clk-master: re-factor master clock Claudiu Beznea
2020-11-06 9:28 ` [PATCH v3 11/11] clk: at91: sama7g5: register cpu clock Claudiu Beznea
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1604654884-30339-10-git-send-email-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=eugen.hristev@microchip.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=mturquette@baylibre.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).