Re: [PATCH v3 2/2] PCI: mediatek-gen3: Add support for disable dvfsrc voltage request

[Qizhong Cheng <qizhong.cheng@mediatek.com>]

Reviewed-by: Qizhong Cheng <qizhong.cheng@mediatek.com>
Tested-by: Qizhong Cheng <qizhong.cheng@mediatek.com>

On Wed, 2021-06-30 at 10:49 +0800, Jianjun Wang wrote:
> PCIe Gen3 PHY layer cannot work properly when the requested voltage
> is lower than a specific level(e.g. 0.55V, it's depends on
> the chip manufacturing process).
> 
> When the dvfsrc feature is implemented, the requested voltage
> may be reduced to a lower level in suspend mode, hence that
> the MAC layer will assert a HW signal to request the dvfsrc
> to raise voltage to normal mode, and it will wait the voltage
> ready signal from dvfsrc to decide if the LTSSM can start normally.
> 
> When the dvfsrc feature is not implemented, the MAC layer still
> assert the voltage request to dvfsrc when exit suspend mode,
> but will not receive the voltage ready signal, in this case,
> the LTSSM cannot start normally, and the PCIe link will be failed.
> 
> Add support for disable dvfsrc voltage request, if the property of
> "disable-dvfsrc-vlt-req" is presented in device node, we assume that
> the requested voltage is always higher enough to keep the PCIe Gen3
> PHY active, and the voltage request to dvfsrc should be disabled.
> 
> Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
> ---
>  drivers/pci/controller/pcie-mediatek-gen3.c | 31 +++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/drivers/pci/controller/pcie-mediatek-gen3.c b/drivers/pci/controller/pcie-mediatek-gen3.c
> index 3c5b97716d40..028014707588 100644
> --- a/drivers/pci/controller/pcie-mediatek-gen3.c
> +++ b/drivers/pci/controller/pcie-mediatek-gen3.c
> @@ -79,6 +79,9 @@
>  #define PCIE_ICMD_PM_REG		0x198
>  #define PCIE_TURN_OFF_LINK		BIT(4)
>  
> +#define PCIE_MISC_CTRL_REG		0x348
> +#define PCIE_DISABLE_DVFSRC_VLT_REQ	BIT(1)
> +
>  #define PCIE_TRANS_TABLE_BASE_REG	0x800
>  #define PCIE_ATR_SRC_ADDR_MSB_OFFSET	0x4
>  #define PCIE_ATR_TRSL_ADDR_LSB_OFFSET	0x8
> @@ -297,6 +300,34 @@ static int mtk_pcie_startup_port(struct mtk_pcie_port *port)
>  	val &= ~PCIE_INTX_ENABLE;
>  	writel_relaxed(val, port->base + PCIE_INT_ENABLE_REG);
>  
> +	/*
> +	 * PCIe Gen3 PHY layer can not work properly when the requested voltage
> +	 * is lower than a specific level(e.g. 0.55V, it's depends on
> +	 * the chip manufacturing process).
> +	 *
> +	 * When the dvfsrc feature is implemented, the requested voltage
> +	 * might be reduced to a lower level in suspend mode, hence that
> +	 * the MAC layer will assert a HW signal to request the dvfsrc
> +	 * to raise voltage to normal mode, and it will wait the voltage
> +	 * ready signal from dvfsrc to start the LTSSM normally.
> +	 *
> +	 * When the dvfsrc feature is not implemented, the MAC layer still
> +	 * assert the voltage request to dvfsrc when exit suspend mode,
> +	 * but will not get the voltage ready signal, in this case, the LTSSM
> +	 * cannot start normally, and the PCIe link will be failed.
> +	 *
> +	 * If the property of "disable-dvfsrc-vlt-req" is presented
> +	 * in device node, we assume that the requested voltage is always
> +	 * higher enough to keep the PCIe Gen3 PHY active, and the voltage
> +	 * request to dvfsrc should be disabled.
> +	 */
> +	val = readl_relaxed(port->base + PCIE_MISC_CTRL_REG);
> +	val &= ~PCIE_DISABLE_DVFSRC_VLT_REQ;
> +	if (of_property_read_bool(port->dev->of_node, "disable-dvfsrc-vlt-req"))
> +		val |= PCIE_DISABLE_DVFSRC_VLT_REQ;
> +
> +	writel_relaxed(val, port->base + PCIE_MISC_CTRL_REG);
> +
>  	/* Assert all reset signals */
>  	val = readl_relaxed(port->base + PCIE_RST_CTRL_REG);
>  	val |= PCIE_MAC_RSTB | PCIE_PHY_RSTB | PCIE_BRG_RSTB | PCIE_PE_RSTB;