[PATCH 6/6] arm64: dts: imx8mn-evk: add sdio wifi support

[haibo.chen@nxp.com]

From: Haibo Chen <haibo.chen@nxp.com>

Add sdio wifi support on imx8mn-evk board.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi | 59 +++++++++++++++++++
 1 file changed, 59 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
index 85e65f8719ea..00064f198423 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
@@ -28,6 +28,13 @@
 		reg = <0x0 0x40000000 0 0x80000000>;
 	};
 
+	usdhc1_pwrseq: usdhc1_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc1_gpio>;
+		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -205,6 +212,19 @@
 	};
 };
 
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	fsl,sdio-async-interrupt-enabled;
+	status = "okay";
+};
+
 &usdhc2 {
 	assigned-clocks = <&clk IMX8MN_CLK_USDHC2>;
 	assigned-clock-rates = <200000000>;
@@ -303,6 +323,45 @@
 		>;
 	};
 
+	pinctrl_usdhc1_gpio: usdhc1grpgpio {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_RESET_B_GPIO2_IO10	0x41
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK		0x190
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d0
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d0
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d0
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK		0x194
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d4
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d4
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d4
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK		0x196
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0	0x1d6
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1	0x1d6
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2	0x1d6
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3	0x1d6
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x41
-- 
2.17.1