From: Kieran Bingham <kieran.bingham@ideasonboard.com>
To: Petko Manolov <petko.manolov@konsulko.com>, linux-media@vger.kernel.org
Cc: sakari.ailus@iki.fi, devicetree@vger.kernel.org,
Petko Manolov <petko.manolov@konsulko.com>
Subject: Re: [PATCH v5 1/2] media: ovm6211: Adds support for OVM6211
Date: Wed, 09 Mar 2022 11:51:27 +0000 [thread overview]
Message-ID: <164682668750.856468.1538708322661359680@Monstersaurus> (raw)
In-Reply-To: <20220309102215.891001-2-petko.manolov@konsulko.com>
Hi Petko,
Quoting Petko Manolov (2022-03-09 10:22:14)
> OVM6211 is a black and white 160 kpixel (400x400) camera sensor from OmniVision.
> It supports 400x400, 200x200 and 100x100 image sizes. With careful register
Looking below, I see you only have 400x400 and 400x200 modes
implemented. It might be worth stating that here in the commit message.
I started looking through here with the assumption you are supporting
{400x400}, {200x200}, and {100x100}, but can see it's actually {400x400}
and {400x200}.
> programming it is possible to have non-square sizes as well. The output formats
> are 8/10-bit RAW, this driver is only using the former. OVM6211 supports a
> single lane MIPI transmitter interface with up to 600 Mbps data rate.
Is it possible to implement the HBLANK/VBLANK controls on this sensor? I
see some settings for frame intervals but not blanking. Perhaps the
blanking is fixed? (I see it's a global shutter sensor, I'm not sure if
that makes a difference here...)
Also I see there is exposure control, but no gain. Should
V4L2_CID_ANALOGUE_GAIN be implemented/supported?
https://www.ovt.com/wp-content/uploads/2022/01/OVM6211-PB-v1.6-WEB.pdf
shows at least that there is a gain control component.
>
> Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
> ---
> drivers/media/i2c/Kconfig | 10 +
> drivers/media/i2c/Makefile | 1 +
> drivers/media/i2c/ovm6211.c | 1018 +++++++++++++++++++++++++++++++++++
> 3 files changed, 1029 insertions(+)
> create mode 100644 drivers/media/i2c/ovm6211.c
>
> diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> index fe66093b8849..aebe6a5f237e 100644
> --- a/drivers/media/i2c/Kconfig
> +++ b/drivers/media/i2c/Kconfig
> @@ -1049,6 +1049,16 @@ config VIDEO_OV5648
> To compile this driver as a module, choose M here: the
> module will be called ov5648.
>
> +config VIDEO_OVM6211
> + tristate "OmniVision OVM6211 sensor support"
> + depends on I2C && VIDEO_V4L2
> + help
> + This is a Video4Linux2 sensor driver for the OmniVision
> + OVM6211 camera.
> +
> + To compile this driver as a module, choose M here: the
> + module will be called ovm6211.
> +
> config VIDEO_OV6650
> tristate "OmniVision OV6650 sensor support"
> depends on I2C && VIDEO_V4L2
> diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> index f6b80ef6f41d..9e9998966c18 100644
> --- a/drivers/media/i2c/Makefile
> +++ b/drivers/media/i2c/Makefile
> @@ -78,6 +78,7 @@ obj-$(CONFIG_VIDEO_OV5670) += ov5670.o
> obj-$(CONFIG_VIDEO_OV5675) += ov5675.o
> obj-$(CONFIG_VIDEO_OV5693) += ov5693.o
> obj-$(CONFIG_VIDEO_OV5695) += ov5695.o
> +obj-$(CONFIG_VIDEO_OVM6211) += ovm6211.o
> obj-$(CONFIG_VIDEO_OV6650) += ov6650.o
> obj-$(CONFIG_VIDEO_OV7251) += ov7251.o
> obj-$(CONFIG_VIDEO_OV7640) += ov7640.o
> diff --git a/drivers/media/i2c/ovm6211.c b/drivers/media/i2c/ovm6211.c
> new file mode 100644
> index 000000000000..7cfcc0bf5e48
> --- /dev/null
> +++ b/drivers/media/i2c/ovm6211.c
> @@ -0,0 +1,1018 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (C) 2021 Petko Manolov <petko.manolov@konsulko.com>
> + * Copyright (C) 2021 DEKA Research & Development Corp.
> + */
> +
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/regmap.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +#include <linux/types.h>
> +#include <media/v4l2-async.h>
> +#include <media/v4l2-ctrls.h>
> +#include <media/v4l2-device.h>
> +#include <media/v4l2-event.h>
> +#include <media/v4l2-fwnode.h>
> +#include <media/v4l2-subdev.h>
> +
> +/* System Control */
> +#define OVM6211_SC_MODE_SELECT 0x0100
> +#define OVM6211_SC_SOFTWARE_RESET 0x0103
> +#define OVM6211_SC_SCCB_ID1 0x0109
> +#define OVM6211_SC_CHIP_ID_HIGH 0x300a
> +#define OVM6211_SC_CHIP_ID_LOW 0x300b
> +#define OVM6211_SC_REG0C 0x300c
> +#define OVM6211_SC_REG10 0x3010
> +#define OVM6211_SC_MIPI_PHY 0x3012
> +#define OVM6211_SC_MIPI_PHY2 0x3013
> +#define OVM6211_SC_MIPI_SC_CTRL0 0x3014
> +#define OVM6211_SC_MIPI_SC_CTRL1 0x3015
> +#define OVM6211_SC_CLKRST0 0x3016
> +#define OVM6211_SC_CLKRST1 0x3017
> +#define OVM6211_SC_CLKRST2 0x3018
> +#define OVM6211_SC_CLKRST3 0x3019
> +#define OVM6211_SC_CLKRST4 0x301a
> +#define OVM6211_SC_CLKRST5 0x301b
> +#define OVM6211_SC_CLKRST6 0x301c
> +#define OVM6211_SC_CLOCK_SEL 0x301e
> +#define OVM6211_SC_MISC_CTRL 0x301f
> +#define OVM6211_SC_LOW_PWR_CTRL 0x3023
> +#define OVM6211_SC_REG27 0x3027
> +#define OVM6211_SC_GP_IO_IN1 0x3029
> +#define OVM6211_SC_GP_IO_IN2 0x302a
> +#define OVM6211_SC_SCCB_ID2 0x302b
> +#define OVM6211_SC_AUTO_SLEEP_PERIOD0 0x302c
> +#define OVM6211_SC_AUTO_SLEEP_PERIOD1 0x302d
> +#define OVM6211_SC_AUTO_SLEEP_PERIOD2 0x302e
> +#define OVM6211_SC_AUTO_SLEEP_PERIOD3 0x302f
> +#define OVM6211_SC_LP_CTRL0 0x3030
> +#define OVM6211_SC_REG37 0x3037
> +#define OVM6211_SC_REG3B 0x303b
> +/* PLL Control */
> +#define OVM6211_PLL_PLL0 0x3080
> +#define OVM6211_PLL_PLL1 0x3081
> +#define OVM6211_PLL_PLL2 0x3082
> +#define OVM6211_PLL_PLL18 0x3098
> +#define OVM6211_PLL_PLL19 0x3099
> +#define OVM6211_PLL_PLL1A 0x309a
> +#define OVM6211_PLL_PLL1B 0x309b
> +#define OVM6211_PLL_PLL1C 0x309c
> +#define OVM6211_PLL_PLL1D 0x309d
> +#define OVM6211_PLL_PLL1E 0x309e
> +#define OVM6211_PLL_PLL1F 0x309f
> +#define OVM6211_PLL_VT_PIX_CLK_DIV 0x30b0
> +#define OVM6211_PLL_VT_SYS_CLK_DIV 0x30b1
> +#define OVM6211_PLL_MULTIPLIER 0x30b3
> +#define OVM6211_PLL_PLL1_PRE_PLL_DIV 0x30b4
> +#define OVM6211_PLL_PLL1_OP_PIX_CLK_DIV 0x30b5
> +#define OVM6211_PLL_PLL1_OP_SYS_CLK_DIV 0x30b6
> +/* SCCB and group hold */
> +#define OVM6211_SB_SRB_CTRL 0x3106
> +#define OVM6211_SB_SWITCH 0x31ff
> +/* AEC/AGC */
> +#define OVM6211_AEC_EXPO1 0x3500
> +#define OVM6211_AEC_EXPO2 0x3501
> +#define OVM6211_AEC_EXPO3 0x3502
> +#define OVM6211_AEC_MANUAL 0x3503
> +#define OVM6211_AGC_MAN_SNR_GAIN1 0x3504
> +#define OVM6211_AGC_MAN_SNR_GAIN2 0x3505
> +/* timing conrol registers */
> +#define OVM6211_TVTS_HI 0x380e
> +#define OVM6211_TVTS_LO 0x380f
> +/*Strobe frame span registers*/
> +#define OVM6211_STROBE_SPAN1 0x3b8d
> +#define OVM6211_STROBE_SPAN2 0x3b8e
> +#define OVM6211_STROBE_SPAN3 0x3b8f
> +/* format control */
> +#define OVM6211_DATA_MAX_H 0x4300
> +#define OVM6211_DATA_MIN_H 0x4301
> +#define OVM6211_CLIP_L 0x4302
> +#define OVM6211_FORMAT_CTRL3 0x4303
> +#define OVM6211_FORMAT_CTRL4 0x4304
> +#define OVM6211_VSYNC_WIDTH_H 0x4311
> +#define OVM6211_VSYNC_WIDTH_L 0x4312
> +#define OVM6211_VSYNC_CTRL 0x4313
> +#define OVM6211_VSYNC_DELAY1 0x4314
> +#define OVM6211_VSYNC_DELAY2 0x4315
> +#define OVM6211_VSYNC_DELAY3 0x4316
> +#define OVM6211_TST_PATTERN_CTRL 0x4320
> +/* MIPI */
> +#define OVM6211_MIPI_CTRL00 0x4800
> +#define OVM6211_MIPI_CTRL01 0x4801
> +#define OVM6211_MIPI_CTRL02 0x4802
> +#define OVM6211_MIPI_CTRL03 0x4803
> +#define OVM6211_MIPI_CTRL04 0x4804
> +#define OVM6211_MIPI_CTRL05 0x4805
> +#define OVM6211_MIPI_CTRL06 0x4806
> +#define OVM6211_MIPI_MAX_FRAME_COUNT_H 0x4810
> +#define OVM6211_MIPI_MAX_FRAME_COUNT_L 0x4811
> +#define OVM6211_MIPI_SHORT_PKT_COUNTER_H 0x4812
> +#define OVM6211_MIPI_SHORT_PKT_COUNTER_L 0x4813
> +#define OVM6211_MIPI_CTRL14 0x4814
> +#define OVM6211_MIPI_DT_SPKT 0x4815
> +#define OVM6211_MIPI_REG_MAX_H 0x4835
> +#define OVM6211_MIPI_REG_MAX_L 0x4836
> +#define OVM6211_PCLK_PERIOD 0x4837
> +#define OVM6211_WKUP_DLY 0x4838
> +#define OVM6211_DIR_DLY 0x483a
> +#define OVM6211_MIPI_LP_GPIO 0x483b
> +#define OVM6211_MIPI_CTRL3C 0x483c
> +#define OVM6211_T_TA_GO 0x483d
> +#define OVM6211_T_TA_SURE 0x483e
> +#define OVM6211_T_TA_GET 0x483f
> +#define OVM6211_MIPI_CLIP_MAX_H 0x4846
> +#define OVM6211_MIPI_CLIP_MAX_L 0x4847
> +#define OVM6211_MIPI_CLIP_MIN_H 0x4848
> +#define OVM6211_MIPI_CLIP_MIN_L 0x4848
> +#define OVM6211_REG_INTR_MAN 0x4850
> +#define OVM6211_REG_TX_WR 0x4851
> +/* ISP top */
> +#define OVM6211_ISP_CTRL00 0x5000
> +#define OVM6211_ISP_CTRL01 0x5001
> +#define OVM6211_ISP_CTRL02 0x5002
> +#define OVM6211_ISP_CTRL03 0x5003
> +#define OVM6211_ISP_CTRL04 0x5004
> +#define OVM6211_ISP_CTRL05 0x5005
> +#define OVM6211_ISP_CTRL06 0x5006
> +#define OVM6211_ISP_CTRL07 0x5007
> +#define OVM6211_ISP_CTRL08 0x5008
> +#define OVM6211_ISP_CTRL09 0x5009
> +/* window control */
> +#define OVM6211_MAN_XSTART_OFF_H 0x5a00
> +#define OVM6211_MAN_XSTART_OFF_L 0x5a01
> +#define OVM6211_MAN_YSTART_OFF_H 0x5a02
> +#define OVM6211_MAN_YSTART_OFF_L 0x5a03
> +#define OVM6211_MAN_WIN_WIDTH_H 0x5a04
> +#define OVM6211_MAN_WIN_WIDTH_L 0x5a05
> +#define OVM6211_MAN_WIN_HEIGHT_H 0x5a06
> +#define OVM6211_MAN_WIN_HEIGHT_L 0x5a07
> +#define OVM6211_WIN_MAN 0x5a08
> +
> +#define OVM6211_LAST_REG 0x5e08
> +/* end of OVM6211 definitions */
> +
> +#define DEF_LINK_FREQ 38400000LL
> +
> +enum ovm6211_mode_id {
> + OVM6211_MODE_Y8_400_200 = 0,
> + OVM6211_MODE_Y8_400_400,
> + OVM6211_NUM_MODES,
> +};
> +
> +struct ovm6211_pixfmt {
> + u32 code;
> + u32 colorspace;
> +};
> +
> +static const struct ovm6211_pixfmt ovm6211_formats[] = {
> + { MEDIA_BUS_FMT_Y8_1X8, V4L2_COLORSPACE_RAW, },
> + { MEDIA_BUS_FMT_Y8_1X8, V4L2_COLORSPACE_RAW, },
Is one entry enough here?
The color space isn't even used is it?
It could probably be hardcoded in ovm6211_enum_mbus_code(), and then get
rid of struct ovm6211_pixfmt too?
Unless you expect other bus formats or colorspace to be supported?
> +};
> +
> +enum ovm6211_framerate_ids {
> + OVM6211_10_FPS = 0,
> + OVM6211_15_FPS,
> + OVM6211_30_FPS,
> + OVM6211_45_FPS,
> + OVM6211_60_FPS,
> + OVM6211_NUM_FRAMERATES,
> +};
> +
> +static const int ovm6211_framerates[] = {
> + [OVM6211_10_FPS] = 10,
> + [OVM6211_15_FPS] = 15,
> + [OVM6211_30_FPS] = 30,
> + [OVM6211_45_FPS] = 45,
> + [OVM6211_60_FPS] = 60,
> +};
> +
> +/* regulator supplies */
> +static const char * const ovm6211_supply_name[] = {
> + "dovdd",
> + "avdd",
> +};
> +
> +static const struct regmap_config ovm6211_regmap_config = {
> + .reg_bits = 16,
> + .val_bits = 8,
> + .max_register = OVM6211_LAST_REG,
> + .cache_type = REGCACHE_NONE,
> +};
> +
> +struct reg_value {
> + u16 reg_addr;
> + u8 val;
> + u8 mask;
> + u32 delay_ms;
> +};
> +
> +struct ovm6211_mode_info {
> + enum ovm6211_mode_id id;
> + u32 width;
> + u32 height;
> + const struct reg_value *reg_data;
> + u32 reg_data_size;
> + u32 pixel_clock;
> +};
> +
> +struct ovm6211_ctrls {
> + struct v4l2_ctrl_handler handler;
> + struct {
> + struct v4l2_ctrl *auto_exp;
> + struct v4l2_ctrl *exposure;
> + };
> + struct {
> + struct v4l2_ctrl *auto_gain;
> + struct v4l2_ctrl *gain;
> + };
> + struct v4l2_ctrl *link_freq;
> +};
> +
> +struct ovm6211_dev {
> + struct i2c_client *i2c_client;
> + struct regmap *regmap;
> + struct v4l2_subdev sd;
> + struct media_pad pad;
> + struct v4l2_fwnode_endpoint ep; /* the parsed DT endpoint info */
> +
> + struct regulator_bulk_data supplies[ARRAY_SIZE(ovm6211_supply_name)];
> + struct gpio_desc *reset_gpio;
> + struct gpio_desc *pwdn_gpio;
> +
> + struct mutex lock;
> +
> + struct v4l2_mbus_framefmt fmt;
> +
> + const struct ovm6211_mode_info *cur_mode;
> + enum ovm6211_framerate_ids cur_fr_id;
> + struct v4l2_fract frame_interval;
> +
> + struct ovm6211_ctrls ctrls;
> +
> + u32 exposure;
> + bool pending_mode_change;
> + bool pending_fi_change;
> + bool streaming;
> +};
> +
> +static inline struct ovm6211_dev *to_ovm6211_dev(struct v4l2_subdev *sd)
> +{
> + return container_of(sd, struct ovm6211_dev, sd);
> +}
> +
> +static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
> +{
> + return &container_of(ctrl->handler, struct ovm6211_dev,
> + ctrls.handler)->sd;
> +}
> +
> +static const struct reg_value ovm6211_init_y8_400_400[] = {
> + {0x0103, 0x01, 0, 0}, {0x0100, 0x00, 0, 0}, {0x3005, 0x08, 0, 0},
> + {0x3013, 0x12, 0, 0}, {0x3014, 0x04, 0, 0}, {0x3016, 0x10, 0, 0},
> + {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0}, {0x301a, 0x00, 0, 0},
> + {0x301b, 0x00, 0, 0}, {0x301c, 0x00, 0, 0}, {0x3037, 0xf0, 0, 0},
> + {0x3080, 0x01, 0, 0}, {0x3081, 0x00, 0, 0}, {0x3082, 0x01, 0, 0},
> + {0x3098, 0x04, 0, 0}, {0x3099, 0x28, 0, 0}, {0x309a, 0x06, 0, 0},
> + {0x309b, 0x04, 0, 0}, {0x309c, 0x00, 0, 0}, {0x309d, 0x00, 0, 0},
> + {0x309e, 0x01, 0, 0}, {0x309f, 0x00, 0, 0}, {0x30b0, 0x08, 0, 0},
> + {0x30b1, 0x02, 0, 0}, {0x30b2, 0x00, 0, 0}, {0x30b3, 0x28, 0, 0},
> + {0x30b4, 0x02, 0, 0}, {0x30b5, 0x00, 0, 0}, {0x3106, 0xd9, 0, 0},
> + {0x3500, 0x00, 0, 0}, {0x3501, 0x1b, 0, 0}, {0x3502, 0x20, 0, 0},
> + {0x3503, 0x07, 0, 0}, {0x3509, 0x10, 0, 0}, {0x350b, 0x10, 0, 0},
> + {0x3600, 0xfc, 0, 0}, {0x3620, 0xb7, 0, 0}, {0x3621, 0x05, 0, 0},
> + {0x3626, 0x31, 0, 0}, {0x3627, 0x40, 0, 0}, {0x3632, 0xa3, 0, 0},
> + {0x3633, 0x34, 0, 0}, {0x3634, 0x40, 0, 0}, {0x3636, 0x00, 0, 0},
> + {0x3660, 0x80, 0, 0}, {0x3662, 0x03, 0, 0}, {0x3664, 0xf0, 0, 0},
> + {0x366a, 0x10, 0, 0}, {0x366b, 0x06, 0, 0}, {0x3680, 0xf4, 0, 0},
> + {0x3681, 0x50, 0, 0}, {0x3682, 0x00, 0, 0}, {0x3708, 0x20, 0, 0},
> + {0x3709, 0x40, 0, 0}, {0x370d, 0x03, 0, 0}, {0x373b, 0x02, 0, 0},
> + {0x373c, 0x08, 0, 0}, {0x3742, 0x00, 0, 0}, {0x3744, 0x16, 0, 0},
> + {0x3745, 0x08, 0, 0}, {0x3781, 0xfc, 0, 0}, {0x3788, 0x00, 0, 0},
> + {0x3800, 0x00, 0, 0}, {0x3801, 0x04, 0, 0}, {0x3802, 0x00, 0, 0},
> + {0x3803, 0x04, 0, 0}, {0x3804, 0x01, 0, 0}, {0x3805, 0x9b, 0, 0},
> + {0x3806, 0x01, 0, 0}, {0x3807, 0x9b, 0, 0}, {0x3808, 0x01, 0, 0},
> + {0x3809, 0x90, 0, 0}, {0x380a, 0x01, 0, 0}, {0x380b, 0x90, 0, 0},
> + {0x380c, 0x05, 0, 0}, {0x380d, 0xf2, 0, 0}, {0x380e, 0x03, 0, 0},
> + {0x380f, 0x6c, 0, 0}, {0x3810, 0x00, 0, 0}, {0x3811, 0x04, 0, 0},
> + {0x3812, 0x00, 0, 0}, {0x3813, 0x04, 0, 0}, {0x3814, 0x11, 0, 0},
> + {0x3815, 0x11, 0, 0}, {0x3820, 0x00, 0, 0}, {0x3821, 0x00, 0, 0},
> + {0x382b, 0xfa, 0, 0}, {0x382f, 0x04, 0, 0}, {0x3832, 0x00, 0, 0},
> + {0x3833, 0x05, 0, 0}, {0x3834, 0x00, 0, 0}, {0x3835, 0x05, 0, 0},
> + {0x3882, 0x04, 0, 0}, {0x3883, 0x00, 0, 0}, {0x38a4, 0x10, 0, 0},
> + {0x38a5, 0x00, 0, 0}, {0x38b1, 0x03, 0, 0}, {0x3b80, 0x00, 0, 0},
> + {0x3b81, 0xff, 0, 0}, {0x3b82, 0x10, 0, 0}, {0x3b83, 0x00, 0, 0},
> + {0x3b84, 0x08, 0, 0}, {0x3b85, 0x00, 0, 0}, {0x3b86, 0x01, 0, 0},
> + {0x3b87, 0x00, 0, 0}, {0x3b88, 0x00, 0, 0}, {0x3b89, 0x00, 0, 0},
> + {0x3b8a, 0x00, 0, 0}, {0x3b8b, 0x05, 0, 0}, {0x3b8c, 0x00, 0, 0},
> + {0x3b8d, 0x00, 0, 0}, {0x3b8e, 0x01, 0, 0}, {0x3b8f, 0xb2, 0, 0},
> + {0x3b94, 0x05, 0, 0}, {0x3b95, 0xf2, 0, 0}, {0x3b96, 0xc0, 0, 0},
> + {0x4004, 0x04, 0, 0}, {0x404e, 0x01, 0, 0}, {0x4801, 0x0f, 0, 0},
> + {0x4806, 0x0f, 0, 0}, {0x4837, 0x43, 0, 0}, {0x5a08, 0x00, 0, 0},
> + {0x5a01, 0x00, 0, 0}, {0x5a03, 0x00, 0, 0}, {0x5a04, 0x10, 0, 0},
> + {0x5a05, 0xa0, 0, 0}, {0x5a06, 0x0c, 0, 0}, {0x5a07, 0x78, 0, 0},
> +};
> +
> +static const struct reg_value ovm6211_init_y8_400_200[] = {
> + {0x0103, 0x01, 0, 0}, {0x0100, 0x00, 0, 0}, {0x3005, 0x08, 0, 0},
> + {0x3013, 0x12, 0, 0}, {0x3014, 0x04, 0, 0}, {0x3016, 0x10, 0, 0},
> + {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0}, {0x301a, 0x00, 0, 0},
> + {0x301b, 0x00, 0, 0}, {0x301c, 0x00, 0, 0}, {0x3037, 0xf0, 0, 0},
> + {0x3080, 0x01, 0, 0}, {0x3081, 0x00, 0, 0}, {0x3082, 0x01, 0, 0},
> + {0x3098, 0x04, 0, 0}, {0x3099, 0x28, 0, 0}, {0x309a, 0x06, 0, 0},
> + {0x309b, 0x04, 0, 0}, {0x309c, 0x00, 0, 0}, {0x309d, 0x00, 0, 0},
> + {0x309e, 0x01, 0, 0}, {0x309f, 0x00, 0, 0}, {0x30b0, 0x08, 0, 0},
> + {0x30b1, 0x02, 0, 0}, {0x30b2, 0x00, 0, 0}, {0x30b3, 0x28, 0, 0},
> + {0x30b4, 0x02, 0, 0}, {0x30b5, 0x00, 0, 0}, {0x3106, 0xd9, 0, 0},
> + {0x3500, 0x00, 0, 0}, {0x3501, 0x1b, 0, 0}, {0x3502, 0x20, 0, 0},
> + {0x3503, 0x07, 0, 0}, {0x3509, 0x10, 0, 0}, {0x350b, 0x10, 0, 0},
> + {0x3600, 0xfc, 0, 0}, {0x3620, 0xb7, 0, 0}, {0x3621, 0x05, 0, 0},
> + {0x3626, 0x31, 0, 0}, {0x3627, 0x40, 0, 0}, {0x3632, 0xa3, 0, 0},
> + {0x3633, 0x34, 0, 0}, {0x3634, 0x40, 0, 0}, {0x3636, 0x00, 0, 0},
> + {0x3660, 0x80, 0, 0}, {0x3662, 0x03, 0, 0}, {0x3664, 0xf0, 0, 0},
> + {0x366a, 0x10, 0, 0}, {0x366b, 0x06, 0, 0}, {0x3680, 0xf4, 0, 0},
> + {0x3681, 0x50, 0, 0}, {0x3682, 0x00, 0, 0}, {0x3708, 0x20, 0, 0},
> + {0x3709, 0x40, 0, 0}, {0x370d, 0x03, 0, 0}, {0x373b, 0x02, 0, 0},
> + {0x373c, 0x08, 0, 0}, {0x3742, 0x00, 0, 0}, {0x3744, 0x16, 0, 0},
> + {0x3745, 0x08, 0, 0}, {0x3781, 0xfc, 0, 0}, {0x3788, 0x00, 0, 0},
> + {0x3800, 0x00, 0, 0}, {0x3801, 0x04, 0, 0}, {0x3802, 0x00, 0, 0},
> + {0x3803, 0x04, 0, 0}, {0x3804, 0x01, 0, 0}, {0x3805, 0x9b, 0, 0},
> + {0x3806, 0x01, 0, 0}, {0x3807, 0x9b, 0, 0}, {0x3808, 0x01, 0, 0},
> + {0x3809, 0x90, 0, 0}, {0x380a, 0x00, 0, 0}, {0x380b, 0xc8, 0, 0},
> + {0x380c, 0x05, 0, 0}, {0x380d, 0xf2, 0, 0}, {0x380e, 0x0d, 0, 0},
> + {0x380f, 0xb0, 0, 0}, {0x3810, 0x00, 0, 0}, {0x3811, 0x04, 0, 0},
> + {0x3812, 0x00, 0, 0}, {0x3813, 0x9a, 0, 0}, {0x3814, 0x11, 0, 0},
> + {0x3815, 0x11, 0, 0}, {0x3820, 0x00, 0, 0}, {0x3821, 0x00, 0, 0},
> + {0x382b, 0xfa, 0, 0}, {0x382f, 0x04, 0, 0}, {0x3832, 0x00, 0, 0},
> + {0x3833, 0x05, 0, 0}, {0x3834, 0x00, 0, 0}, {0x3835, 0x05, 0, 0},
> + {0x3882, 0x04, 0, 0}, {0x3883, 0x00, 0, 0}, {0x38a4, 0x10, 0, 0},
> + {0x38a5, 0x00, 0, 0}, {0x38b1, 0x03, 0, 0}, {0x3b80, 0x00, 0, 0},
> + {0x3b81, 0xff, 0, 0}, {0x3b82, 0x10, 0, 0}, {0x3b83, 0x00, 0, 0},
> + {0x3b84, 0x08, 0, 0}, {0x3b85, 0x00, 0, 0}, {0x3b86, 0x01, 0, 0},
> + {0x3b87, 0x00, 0, 0}, {0x3b88, 0x00, 0, 0}, {0x3b89, 0x00, 0, 0},
> + {0x3b8a, 0x00, 0, 0}, {0x3b8b, 0x05, 0, 0}, {0x3b8c, 0x00, 0, 0},
> + {0x3b8d, 0x00, 0, 0}, {0x3b8e, 0x01, 0, 0}, {0x3b8f, 0xb2, 0, 0},
> + {0x3b94, 0x05, 0, 0}, {0x3b95, 0xf2, 0, 0}, {0x3b96, 0xc0, 0, 0},
> + {0x4004, 0x04, 0, 0}, {0x404e, 0x01, 0, 0}, {0x4801, 0x0f, 0, 0},
> + {0x4806, 0x0f, 0, 0}, {0x4837, 0x43, 0, 0}, {0x5a08, 0x00, 0, 0},
> + {0x5a01, 0x00, 0, 0}, {0x5a03, 0x00, 0, 0}, {0x5a04, 0x10, 0, 0},
> + {0x5a05, 0xa0, 0, 0}, {0x5a06, 0x0c, 0, 0}, {0x5a07, 0x78, 0, 0},
> +};
> +
> +static struct ovm6211_mode_info
> +ovm6211_mode_data[OVM6211_NUM_MODES] = {
> + {OVM6211_MODE_Y8_400_200,
> + 400, 200,
> + ovm6211_init_y8_400_200,
> + ARRAY_SIZE(ovm6211_init_y8_400_200),
> + 400 * 400 * 60 * 2,
> + },
> + {OVM6211_MODE_Y8_400_400,
> + 400, 400,
> + ovm6211_init_y8_400_400,
> + ARRAY_SIZE(ovm6211_init_y8_400_400),
> + 400 * 400 * 60 * 2,
> + },
> +};
> +
> +static const s64 link_freq_menu_items[] = {
> + DEF_LINK_FREQ,
> +};
> +
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> +static int ovm6211_get_register(struct v4l2_subdev *sd,
> + struct v4l2_dbg_register *reg)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + struct regmap *regmap = sensor->regmap;
> + unsigned int val = 0;
> + int ret;
> +
> + ret = regmap_read(regmap, reg->reg, &val);
> + reg->val = val;
> + reg->size = 1;
> +
> + return ret;
> +}
> +
> +static int ovm6211_set_register(struct v4l2_subdev *sd,
> + const struct v4l2_dbg_register *reg)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + struct regmap *regmap = sensor->regmap;
> +
> + return regmap_write(regmap, reg->reg, reg->val & 0xff);
> +}
> +#endif
> +
> +static int ovm6211_write_reg(struct ovm6211_dev *sensor, u16 reg, u8 val)
> +{
> + struct i2c_client *client = sensor->i2c_client;
> + struct regmap *regmap = sensor->regmap;
> + int ret;
> +
> + ret = regmap_write(regmap, reg, val);
> + if (ret < 0)
> + dev_err(&client->dev, "error writing reg %u\n", reg);
> +
> + return ret;
> +}
> +
> +static int ovm6211_read_reg(struct ovm6211_dev *sensor, u16 reg, u8 *val)
> +{
> + struct i2c_client *client = sensor->i2c_client;
> + struct regmap *regmap = sensor->regmap;
> + unsigned int r;
> + int ret;
> +
> + ret = regmap_read(regmap, reg, &r);
> + if (ret < 0)
> + dev_err(&client->dev, "error reading reg %u\n", reg);
> + *val = r & 0xff;
> +
> + return ret;
> +}
> +
> +static int ovm6211_mod_reg(struct ovm6211_dev *sensor, u16 reg, u8 mask, u8 val)
> +{
> + u8 readval;
> + int ret;
> +
> + ret = ovm6211_read_reg(sensor, reg, &readval);
> + if (ret)
> + return ret;
> +
> + readval &= ~mask;
> + val &= mask;
> + val |= readval;
> +
> + return ovm6211_write_reg(sensor, reg, val);
> +}
> +
> +static int ovm6211_load_regs(struct ovm6211_dev *sensor,
> + const struct ovm6211_mode_info *mode)
> +{
> + const struct reg_value *regs = mode->reg_data;
> + unsigned int i;
> + u32 delay_ms;
> + u16 reg_addr;
> + u8 mask, val;
> + int ret = 0;
> +
> + for (i = 0; i < mode->reg_data_size; ++i, ++regs) {
> + delay_ms = regs->delay_ms;
> + reg_addr = regs->reg_addr;
> + val = regs->val;
> + mask = regs->mask;
> +
> + if (mask)
> + ret = ovm6211_mod_reg(sensor, reg_addr, mask, val);
> + else
> + ret = ovm6211_write_reg(sensor, reg_addr, val);
> +
> + if (ret)
> + break;
> +
> + if (delay_ms)
> + usleep_range(1000 * delay_ms, 1000 * delay_ms + 100);
> + }
> +
> + return ret;
> +}
> +
> +static void ovm6211_soft_reset(struct ovm6211_dev *sensor)
> +{
> + ovm6211_write_reg(sensor, OVM6211_SC_SOFTWARE_RESET, 0x01);
> + usleep_range(5000, 9000);
> + ovm6211_write_reg(sensor, OVM6211_SC_SOFTWARE_RESET, 0x00);
> +}
> +
> +static int ovm6211_set_exposure(struct ovm6211_dev *sensor, u32 exposure)
> +{
> + u32 ce;
> + u8 v;
> +
> + ovm6211_read_reg(sensor, OVM6211_TVTS_HI, &v);
> + ce = v << 8;
> + ovm6211_read_reg(sensor, OVM6211_TVTS_LO, &v);
> + ce |= v;
> + ce -= 4;
> +
> + if (ce < exposure)
> + exposure = ce;
> +
> + ovm6211_mod_reg(sensor, OVM6211_AEC_MANUAL, 1, 1);
> +
> + ovm6211_write_reg(sensor, OVM6211_AEC_EXPO1, (exposure >> 12) & 0x0f);
> + ovm6211_write_reg(sensor, OVM6211_AEC_EXPO2, (exposure >> 4) & 0xff);
> + ovm6211_write_reg(sensor, OVM6211_AEC_EXPO3, (exposure << 4) & 0xf0);
> +
> + /* set strobe width equal to exposure time */
> + ovm6211_write_reg(sensor, OVM6211_STROBE_SPAN1,
> + (exposure >> 16) & 0xff);
> + ovm6211_write_reg(sensor, OVM6211_STROBE_SPAN2,
> + (exposure >> 8) & 0xff);
> + ovm6211_write_reg(sensor, OVM6211_STROBE_SPAN3, (exposure) & 0xff);
> +
> + return 0;
> +}
> +
> +static int internal_set_stream(struct ovm6211_dev *sensor, bool on)
> +{
> + u8 hi, lo;
> +
> + if (sensor->pending_fi_change == false)
> + goto stream;
> +
> + switch (sensor->cur_fr_id) {
> + case OVM6211_10_FPS:
> + hi = 0x14;
> + lo = 0x88;
> + break;
> + case OVM6211_15_FPS:
> + hi = 0x0d;
> + lo = 0xb0;
> + break;
> + case OVM6211_30_FPS:
> + hi = 0x06;
> + lo = 0xd8;
> + break;
> + case OVM6211_45_FPS:
> + hi = 0x04;
> + lo = 0x90;
> + break;
> + case OVM6211_60_FPS:
> + hi = 0x03;
> + lo = 0x6c;
> + break;
> + case OVM6211_NUM_FRAMERATES:
> + return -EINVAL;
> + }
> +
> + sensor->pending_fi_change = false;
> + ovm6211_write_reg(sensor, OVM6211_TVTS_HI, hi);
> + ovm6211_write_reg(sensor, OVM6211_TVTS_LO, lo);
> +stream:
> + ovm6211_write_reg(sensor, OVM6211_SC_MODE_SELECT, 0);
> + if (on) {
> + usleep_range(4000, 5000);
> + if (sensor->exposure)
> + ovm6211_set_exposure(sensor, sensor->exposure);
> + ovm6211_write_reg(sensor, OVM6211_SC_MODE_SELECT, 1);
> + sensor->streaming = true;
> + } else {
> + sensor->streaming = false;
> + }
> +
> + return 0;
> +}
> +
> +static struct ovm6211_mode_info *ovm6211_find_mode(int w, int h)
> +{
> + return v4l2_find_nearest_size(ovm6211_mode_data,
> + ARRAY_SIZE(ovm6211_mode_data),
> + width, height, w, h);
> +}
> +
> +static int ovm6211_set_mode(struct ovm6211_dev *sensor)
> +{
> + const struct ovm6211_mode_info *mode = sensor->cur_mode;
> +
> + ovm6211_soft_reset(sensor);
> + ovm6211_load_regs(sensor, mode);
> +
> + return 0;
> +}
> +
> +/* --------------- Subdev Operations --------------- */
> +
> +static int ovm6211_get_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_format *format)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + struct v4l2_mbus_framefmt *fmt;
> +
> + mutex_lock(&sensor->lock);
> +
> + if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
> + fmt = v4l2_subdev_get_try_format(&sensor->sd, state, format->pad);
> + format->format = *fmt;
> + } else {
> + /* these are hardcoded as we don't support anything else */
> + format->format.colorspace = V4L2_COLORSPACE_RAW;
> + format->format.field = V4L2_FIELD_NONE;
> + format->format.code = MEDIA_BUS_FMT_Y8_1X8;
> + format->format.width = sensor->cur_mode->width;
> + format->format.height = sensor->cur_mode->height;
> + }
> +
> + mutex_unlock(&sensor->lock);
> +
> + return 0;
> +}
> +
> +static int ovm6211_set_fmt(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_format *format)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + struct v4l2_mbus_framefmt *fmt = &format->format;
> + struct ovm6211_mode_info *mode;
> +
> + mutex_lock(&sensor->lock);
> +
> + if (sensor->streaming)
> + return -EBUSY;
> +
> + /* these are hardcoded as we don't support anything else */
> + format->format.colorspace = V4L2_COLORSPACE_RAW;
> + format->format.field = V4L2_FIELD_NONE;
> + format->format.code = MEDIA_BUS_FMT_Y8_1X8;
> + mode = ovm6211_find_mode(format->format.width, format->format.height);
> + format->format.width = mode->width;
> + format->format.height = mode->height;
> +
> + if (format->which == V4L2_SUBDEV_FORMAT_TRY) {
> + fmt = v4l2_subdev_get_try_format(&sensor->sd, state, format->pad);
> + *fmt = format->format;
> + goto out;
> + }
> + sensor->cur_mode = mode;
> +out:
> + mutex_unlock(&sensor->lock);
> +
> + return 0;
> +}
> +
> +/*
> + * Sensor Controls.
> + */
> +
> +static int ovm6211_set_ctrl_exposure(struct ovm6211_dev *sensor, enum
> + v4l2_exposure_auto_type auto_exposure)
> +{
> + struct ovm6211_ctrls *ctrls = &sensor->ctrls;
> +
> + if (auto_exposure == V4L2_EXPOSURE_AUTO) {
> + sensor->exposure = 0;
> + } else {
> + sensor->exposure = ctrls->exposure->val;
> + ovm6211_set_exposure(sensor, sensor->exposure);
> + }
> +
> + return 0;
> +}
> +
> +static int ovm6211_s_ctrl(struct v4l2_ctrl *ctrl)
> +{
> + struct v4l2_subdev *sd = ctrl_to_sd(ctrl);
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + int ret;
> +
> + switch (ctrl->id) {
> + case V4L2_CID_EXPOSURE_AUTO:
> + ret = ovm6211_set_ctrl_exposure(sensor, ctrl->val);
> + break;
> + case V4L2_CID_LINK_FREQ:
Is this actually adjustable? Or should LINK_FREQ always return DEF_LINK_FREQ?
Aha perhaps it does because it's a menu entry with only one entry ...
> + return 0;
> + case V4L2_CID_PIXEL_RATE:
Is it valid to just openly accept any LINK_FREQ/PIXEL_RATE?
> + return 0;
> + default:
> + ret = -EINVAL;
> + break;
> + }
> +
> + return ret;
> +}
> +
> +static const struct v4l2_ctrl_ops ovm6211_ctrl_ops = {
> + .s_ctrl = ovm6211_s_ctrl,
> +};
> +
> +static int ovm6211_init_controls(struct ovm6211_dev *sensor)
> +{
> + const struct v4l2_ctrl_ops *ops = &ovm6211_ctrl_ops;
> + struct ovm6211_ctrls *ctrls = &sensor->ctrls;
> + struct v4l2_ctrl_handler *hdl = &ctrls->handler;
> + int ret;
> +
> + v4l2_ctrl_handler_init(hdl, 16);
> +
> + hdl->lock = &sensor->lock;
> +
> + ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_EXPOSURE_AUTO,
> + V4L2_EXPOSURE_MANUAL, 0,
> + V4L2_EXPOSURE_AUTO);
> + ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE,
> + 0, 65535, 1, 0);
> + v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false);
> + ctrls->link_freq = v4l2_ctrl_new_int_menu(hdl, ops, V4L2_CID_LINK_FREQ,
> + 0, 0, link_freq_menu_items);
> +
> + if (hdl->error) {
> + ret = hdl->error;
> + goto free_ctrls;
> + }
> +
> + ctrls->exposure->flags |= V4L2_CTRL_FLAG_VOLATILE;
> + sensor->sd.ctrl_handler = hdl;
> +
> + return 0;
> +
> +free_ctrls:
> + v4l2_ctrl_handler_free(hdl);
> + return ret;
> +}
> +
> +static int ovm6211_g_frame_interval(struct v4l2_subdev *sd,
> + struct v4l2_subdev_frame_interval *fi)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> +
> + mutex_lock(&sensor->lock);
> + fi->interval = sensor->frame_interval;
> + mutex_unlock(&sensor->lock);
> +
> + return 0;
> +}
> +
> +static int internal_set_frame_interval(struct ovm6211_dev *sensor, struct
> + v4l2_subdev_frame_interval *fi)
> +{
> + u32 fr_rate;
> + int i, ret = -EINVAL;
> +
> + if (fi->interval.numerator == 0)
> + goto out;
> +
> + fr_rate = fi->interval.denominator / fi->interval.numerator;
> +
> + for (i = 0; i < ARRAY_SIZE(ovm6211_framerates); i++) {
> + if (ovm6211_framerates[i] == fr_rate)
> + break;
> + }
> +
> + if (i == ARRAY_SIZE(ovm6211_framerates))
> + goto out;
> +
> + sensor->cur_fr_id = i;
> + sensor->frame_interval = fi->interval;
> + ret = 0;
> +out:
> + return ret;
> +}
> +
> +static int ovm6211_s_frame_interval(struct v4l2_subdev *sd,
> + struct v4l2_subdev_frame_interval *fi)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + int ret;
> +
> + mutex_lock(&sensor->lock);
> + ret = internal_set_frame_interval(sensor, fi);
> + sensor->pending_fi_change = true;
> + mutex_unlock(&sensor->lock);
> +
> + return ret;
> +}
> +
> +static int ovm6211_enum_mbus_code(struct v4l2_subdev *sd,
> + struct v4l2_subdev_state *state,
> + struct v4l2_subdev_mbus_code_enum *code)
> +{
> + if (code->index >= ARRAY_SIZE(ovm6211_formats))
> + return -EINVAL;
> +
> + code->code = ovm6211_formats[code->index].code;
> +
> + return 0;
> +}
> +
> +static int ovm6211_s_stream(struct v4l2_subdev *sd, int enable)
> +{
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> + int ret = 0;
> +
> + mutex_lock(&sensor->lock);
> +
> + if (enable)
> + ret = ovm6211_set_mode(sensor);
> + internal_set_stream(sensor, enable);
> +
> + mutex_unlock(&sensor->lock);
> +
> + return ret;
> +}
> +
> +static const struct v4l2_subdev_core_ops ovm6211_core_ops = {
> +#ifdef CONFIG_VIDEO_ADV_DEBUG
> + .g_register = ovm6211_get_register,
> + .s_register = ovm6211_set_register,
> +#endif
> +};
> +
> +static const struct v4l2_subdev_video_ops ovm6211_video_ops = {
> + .g_frame_interval = ovm6211_g_frame_interval,
> + .s_frame_interval = ovm6211_s_frame_interval,
> + .s_stream = ovm6211_s_stream,
> +};
> +
> +static const struct v4l2_subdev_pad_ops ovm6211_pad_ops = {
> + .enum_mbus_code = ovm6211_enum_mbus_code,
> + .get_fmt = ovm6211_get_fmt,
> + .set_fmt = ovm6211_set_fmt,
> +};
> +
> +static const struct v4l2_subdev_ops ovm6211_subdev_ops = {
> + .core = &ovm6211_core_ops,
> + .video = &ovm6211_video_ops,
> + .pad = &ovm6211_pad_ops,
> +};
> +
> +static int ovm6211_get_regulators(struct ovm6211_dev *sensor)
> +{
> + unsigned int i;
> +
> + for (i = 0; i < ARRAY_SIZE(ovm6211_supply_name); i++)
> + sensor->supplies[i].supply = ovm6211_supply_name[i];
> +
> + return devm_regulator_bulk_get(&sensor->i2c_client->dev,
> + ARRAY_SIZE(ovm6211_supply_name),
> + sensor->supplies);
> +}
> +
> +static int ovm6211_check_chip_id(struct ovm6211_dev *sensor)
> +{
> + struct i2c_client *client = sensor->i2c_client;
> + struct regmap *regmap = sensor->regmap;
> + unsigned int cid;
> + int ret = 0;
> +
> + ret = regmap_read(regmap, OVM6211_SC_CHIP_ID_HIGH, &cid);
> + if (ret || cid != 0x67) {
> + ret = ENXIO;
> + goto err;
> + }
> +
> + ret = regmap_read(regmap, OVM6211_SC_CHIP_ID_LOW, &cid);
> + if (ret || cid != 0x10) {
> + ret = -ENXIO;
> + goto err;
> + }
> +
> + ret = regmap_read(regmap, OVM6211_SC_REG0C, &cid);
> + if (ret)
> + goto err;
> +
> + dev_info(&client->dev,"found OVM6211, sub revision: 0x%02X\n", cid);
> + return 0;
> +err:
> + dev_err(&client->dev, "failed to detect OVM6211\n");
> + return ret;
> +}
> +
> +static int ovm6211_probe(struct i2c_client *client)
> +{
> + struct device *dev = &client->dev;
> + struct fwnode_handle *endpoint;
> + struct ovm6211_dev *sensor;
> + struct v4l2_mbus_framefmt *fmt;
> + int ret;
> +
> + sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
> + if (!sensor)
> + return -ENOMEM;
> +
> + sensor->i2c_client = client;
> +
> + fmt = &sensor->fmt;
> + fmt->code = MEDIA_BUS_FMT_Y8_1X8;
> + fmt->colorspace = V4L2_COLORSPACE_RAW;
> + fmt->field = V4L2_FIELD_NONE;
> + fmt->quantization = V4L2_QUANTIZATION_FULL_RANGE;
> + fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace);
> + fmt->width = 400;
> + fmt->height = 200;
Is the 400x200 mode just subsampling?
Should 400x200 be listed as a supported image size in your commit
message?
> +
> + sensor->frame_interval.numerator = 1;
> + sensor->frame_interval.denominator = ovm6211_framerates[OVM6211_45_FPS];
> + sensor->cur_fr_id = OVM6211_45_FPS;
> + sensor->cur_mode = &ovm6211_mode_data[OVM6211_MODE_Y8_400_200];
> +
> + sensor->ep.bus_type = V4L2_MBUS_CSI2_DPHY;
> + endpoint = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev), NULL);
> + if (!endpoint) {
> + dev_err(dev, "endpoint node not found\n");
> + return -EINVAL;
> + }
> +
> + ret = v4l2_fwnode_endpoint_parse(endpoint, &sensor->ep);
> + fwnode_handle_put(endpoint);
> + if (ret) {
> + dev_err(dev, "Could not parse endpoint\n");
> + return ret;
> + }
> +
> + /* request optional power down pin */
> + sensor->pwdn_gpio = devm_gpiod_get_optional(dev, "powerdown",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(sensor->pwdn_gpio))
> + return PTR_ERR(sensor->pwdn_gpio);
> +
> + /* request optional reset pin */
> + sensor->reset_gpio = devm_gpiod_get_optional(dev, "reset",
> + GPIOD_OUT_HIGH);
> + if (IS_ERR(sensor->reset_gpio))
> + return PTR_ERR(sensor->reset_gpio);
> +
> + sensor->regmap = devm_regmap_init_i2c(client, &ovm6211_regmap_config);
> + if (IS_ERR(sensor->regmap)) {
> + dev_err(dev, "regmap init failed\n");
> + return PTR_ERR(sensor->regmap);
> + }
> +
> + v4l2_i2c_subdev_init(&sensor->sd, client, &ovm6211_subdev_ops);
> +
> + mutex_init(&sensor->lock);
> +
> + sensor->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE |
> + V4L2_SUBDEV_FL_HAS_EVENTS;
> + sensor->pad.flags = MEDIA_PAD_FL_SOURCE;
> + sensor->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> + ret = media_entity_pads_init(&sensor->sd.entity, 1, &sensor->pad);
> + if (ret)
> + goto entity_cleanup;
> +
> + ret = ovm6211_get_regulators(sensor);
> + if (ret)
> + goto entity_cleanup;
> +
> + ret = ovm6211_check_chip_id(sensor);
> + if (ret)
> + goto entity_cleanup;
> +
> + ret = ovm6211_init_controls(sensor);
> + if (ret)
> + goto entity_cleanup;
> +
> + ovm6211_load_regs(sensor, sensor->cur_mode);
> +
> + ret = v4l2_async_register_subdev_sensor(&sensor->sd);
> + if (ret)
> + goto free_ctrls;
> +
> + return 0;
> +
> +free_ctrls:
> + v4l2_ctrl_handler_free(&sensor->ctrls.handler);
> +entity_cleanup:
> + media_entity_cleanup(&sensor->sd.entity);
> + mutex_destroy(&sensor->lock);
> +
> + return ret;
> +}
> +
> +static int ovm6211_remove(struct i2c_client *client)
> +{
> + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> + struct ovm6211_dev *sensor = to_ovm6211_dev(sd);
> +
> + v4l2_async_unregister_subdev(&sensor->sd);
> + media_entity_cleanup(&sensor->sd.entity);
> + v4l2_ctrl_handler_free(&sensor->ctrls.handler);
> + mutex_destroy(&sensor->lock);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id ovm6211_id[] = {
> + { "ovm6211", 0 },
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ovm6211_id);
> +
> +static const struct of_device_id ovm6211_dt_ids[] = {
> + { .compatible = "ovti,ovm6211" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, ovm6211_dt_ids);
> +
> +static struct i2c_driver ovm6211_i2c_driver = {
> + .driver = {
> + .name = "ovm6211",
> + .of_match_table = ovm6211_dt_ids,
> + },
> + .probe_new = ovm6211_probe,
> + .remove = ovm6211_remove,
> +};
> +
> +module_i2c_driver(ovm6211_i2c_driver);
> +
> +MODULE_AUTHOR("Petko Manolov <petko.manolov@konsulko.com>");
> +MODULE_DESCRIPTION("OVM6211 MIPI Camera Subdev Driver");
> +MODULE_LICENSE("GPL");
> --
> 2.30.2
>
next prev parent reply other threads:[~2022-03-09 11:51 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-03-09 10:22 [PATCH v5 0/2] media: ovm6211: Adds support for OVM6211 Petko Manolov
2022-03-09 10:22 ` [PATCH v5 1/2] " Petko Manolov
2022-03-09 11:51 ` Kieran Bingham [this message]
2022-03-09 12:56 ` Dave Stevenson
2022-03-10 12:19 ` kernel test robot
2022-04-19 9:42 ` Sakari Ailus
2022-03-09 10:22 ` [PATCH v5 2/2] dt-bindings: media: add ovti,ovm6211 bindings Petko Manolov
2022-03-09 13:59 ` Rob Herring
2022-03-09 16:20 ` Petko Manolov
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=164682668750.856468.1538708322661359680@Monstersaurus \
--to=kieran.bingham@ideasonboard.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=petko.manolov@konsulko.com \
--cc=sakari.ailus@iki.fi \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox