* [PATCH v2 0/7] clk: qcom: add camera clock controller driver for SM8450 SoC @ 2022-03-14 11:42 Vladimir Zapolskiy 2022-03-14 11:42 ` [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings Vladimir Zapolskiy 2022-03-14 11:42 ` [PATCH v2 2/7] arm64: dts: qcom: sm8450: Add description of camera clock controller Vladimir Zapolskiy 0 siblings, 2 replies; 5+ messages in thread From: Vladimir Zapolskiy @ 2022-03-14 11:42 UTC (permalink / raw) To: Rob Herring, Bjorn Andersson Cc: Andy Gross, Stephen Boyd, Michael Turquette, devicetree, linux-arm-msm, linux-clk The patchset adds support of a camera clock controller found on QCOM SM8450 SoC, noticeably a camcc pll2 is a new "rivian evo" type of pll, its generic support is added in the series. Note that SM8450 ES variant has a slightly different configurtion, the published version is intended to support SM8450 CS SoC. Changes from v1 to v2: * updated qcom,camcc-sm8450.yaml according to review comments from Rob, * changed qcom,camcc-sm8450.h licence to dual one, * disabled camcc device tree node by default, * added Stephen's tag, * rebased the series on top of clk-for-5.18 Vladimir Zapolskiy (7): dt-bindings: clock: add QCOM SM8450 camera clock bindings arm64: dts: qcom: sm8450: Add description of camera clock controller clk: qcom: clk-alpha-pll: fix clk_trion_pll_configure description clk: qcom: clk-alpha-pll: limit exported symbols to GPL licensed code clk: qcom: clk-alpha-pll: export lucid evo PLL configuration interfaces clk: qcom: clk-alpha-pll: add rivian evo PLL configuration interfaces clk: qcom: add camera clock controller driver for SM8450 SoC .../bindings/clock/qcom,camcc-sm8450.yaml | 89 + arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 + drivers/clk/qcom/Kconfig | 7 + drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/camcc-sm8450.c | 2869 +++++++++++++++++ drivers/clk/qcom/clk-alpha-pll.c | 145 +- drivers/clk/qcom/clk-alpha-pll.h | 11 +- include/dt-bindings/clock/qcom,camcc-sm8450.h | 159 + 8 files changed, 3295 insertions(+), 6 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml create mode 100644 drivers/clk/qcom/camcc-sm8450.c create mode 100644 include/dt-bindings/clock/qcom,camcc-sm8450.h -- 2.33.0 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings 2022-03-14 11:42 [PATCH v2 0/7] clk: qcom: add camera clock controller driver for SM8450 SoC Vladimir Zapolskiy @ 2022-03-14 11:42 ` Vladimir Zapolskiy 2022-03-14 14:42 ` Rob Herring 2022-04-13 2:53 ` Bjorn Andersson 2022-03-14 11:42 ` [PATCH v2 2/7] arm64: dts: qcom: sm8450: Add description of camera clock controller Vladimir Zapolskiy 1 sibling, 2 replies; 5+ messages in thread From: Vladimir Zapolskiy @ 2022-03-14 11:42 UTC (permalink / raw) To: Rob Herring, Bjorn Andersson Cc: Andy Gross, Stephen Boyd, Michael Turquette, devicetree, linux-arm-msm, linux-clk The change adds device tree bindings for camera clock controller found on SM8450 SoC. Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> --- Changes from v1 to v2: * updated qcom,camcc-sm8450.yaml according to review comments from Rob, * changed qcom,camcc-sm8450.h license to dual one. .../bindings/clock/qcom,camcc-sm8450.yaml | 89 ++++++++++ include/dt-bindings/clock/qcom,camcc-sm8450.h | 159 ++++++++++++++++++ 2 files changed, 248 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml create mode 100644 include/dt-bindings/clock/qcom,camcc-sm8450.h diff --git a/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml b/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml new file mode 100644 index 000000000000..2ea0fc12dd69 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml @@ -0,0 +1,89 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/qcom,camcc-sm8450.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Camera Clock & Reset Controller Binding for SM8450 + +maintainers: + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> + +description: | + Qualcomm camera clock control module which supports the clocks, resets and + power domains on SM8450. + + See also dt-bindings/clock/qcom,camcc-sm8450.h + +properties: + compatible: + const: qcom,sm8450-camcc + + clocks: + items: + - description: Camera AHB clock from GCC + - description: Board XO source + - description: Board active XO source + - description: Sleep clock source + + clock-names: + items: + - const: iface + - const: bi_tcxo + - const: bi_tcxo_ao + - const: sleep_clk + + power-domains: + maxItems: 1 + description: + A phandle and PM domain specifier for the MMCX power domain. + + required-opps: + description: + A phandle to an OPP node describing required MMCX performance point. + + '#clock-cells': + const: 1 + + '#reset-cells': + const: 1 + + '#power-domain-cells': + const: 1 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - required-opps + - '#clock-cells' + - '#reset-cells' + - '#power-domain-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sm8450.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/power/qcom-rpmpd.h> + clock-controller@ade0000 { + compatible = "qcom,sm8450-camcc"; + reg = <0 0xade0000 0 0x20000>; + clocks = <&gcc GCC_CAMERA_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>, + <&sleep_clk>; + clock-names = "iface", bi_tcxo", "bi_tcxo_ao", "sleep_clk"; + power-domains = <&rpmhpd SM8450_MMCX>; + required-opps = <&rpmhpd_opp_low_svs>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; +... diff --git a/include/dt-bindings/clock/qcom,camcc-sm8450.h b/include/dt-bindings/clock/qcom,camcc-sm8450.h new file mode 100644 index 000000000000..7ff67acf301a --- /dev/null +++ b/include/dt-bindings/clock/qcom,camcc-sm8450.h @@ -0,0 +1,159 @@ +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ +/* + * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved. + */ + +#ifndef _DT_BINDINGS_CLK_QCOM_CAM_CC_SM8450_H +#define _DT_BINDINGS_CLK_QCOM_CAM_CC_SM8450_H + +/* CAM_CC clocks */ +#define CAM_CC_BPS_AHB_CLK 0 +#define CAM_CC_BPS_CLK 1 +#define CAM_CC_BPS_CLK_SRC 2 +#define CAM_CC_BPS_FAST_AHB_CLK 3 +#define CAM_CC_CAMNOC_AXI_CLK 4 +#define CAM_CC_CAMNOC_AXI_CLK_SRC 5 +#define CAM_CC_CAMNOC_DCD_XO_CLK 6 +#define CAM_CC_CCI_0_CLK 7 +#define CAM_CC_CCI_0_CLK_SRC 8 +#define CAM_CC_CCI_1_CLK 9 +#define CAM_CC_CCI_1_CLK_SRC 10 +#define CAM_CC_CORE_AHB_CLK 11 +#define CAM_CC_CPAS_AHB_CLK 12 +#define CAM_CC_CPAS_BPS_CLK 13 +#define CAM_CC_CPAS_FAST_AHB_CLK 14 +#define CAM_CC_CPAS_IFE_0_CLK 15 +#define CAM_CC_CPAS_IFE_1_CLK 16 +#define CAM_CC_CPAS_IFE_2_CLK 17 +#define CAM_CC_CPAS_IFE_LITE_CLK 18 +#define CAM_CC_CPAS_IPE_NPS_CLK 19 +#define CAM_CC_CPAS_SBI_CLK 20 +#define CAM_CC_CPAS_SFE_0_CLK 21 +#define CAM_CC_CPAS_SFE_1_CLK 22 +#define CAM_CC_CPHY_RX_CLK_SRC 23 +#define CAM_CC_CSI0PHYTIMER_CLK 24 +#define CAM_CC_CSI0PHYTIMER_CLK_SRC 25 +#define CAM_CC_CSI1PHYTIMER_CLK 26 +#define CAM_CC_CSI1PHYTIMER_CLK_SRC 27 +#define CAM_CC_CSI2PHYTIMER_CLK 28 +#define CAM_CC_CSI2PHYTIMER_CLK_SRC 29 +#define CAM_CC_CSI3PHYTIMER_CLK 30 +#define CAM_CC_CSI3PHYTIMER_CLK_SRC 31 +#define CAM_CC_CSI4PHYTIMER_CLK 32 +#define CAM_CC_CSI4PHYTIMER_CLK_SRC 33 +#define CAM_CC_CSI5PHYTIMER_CLK 34 +#define CAM_CC_CSI5PHYTIMER_CLK_SRC 35 +#define CAM_CC_CSID_CLK 36 +#define CAM_CC_CSID_CLK_SRC 37 +#define CAM_CC_CSID_CSIPHY_RX_CLK 38 +#define CAM_CC_CSIPHY0_CLK 39 +#define CAM_CC_CSIPHY1_CLK 40 +#define CAM_CC_CSIPHY2_CLK 41 +#define CAM_CC_CSIPHY3_CLK 42 +#define CAM_CC_CSIPHY4_CLK 43 +#define CAM_CC_CSIPHY5_CLK 44 +#define CAM_CC_FAST_AHB_CLK_SRC 45 +#define CAM_CC_GDSC_CLK 46 +#define CAM_CC_ICP_AHB_CLK 47 +#define CAM_CC_ICP_CLK 48 +#define CAM_CC_ICP_CLK_SRC 49 +#define CAM_CC_IFE_0_CLK 50 +#define CAM_CC_IFE_0_CLK_SRC 51 +#define CAM_CC_IFE_0_DSP_CLK 52 +#define CAM_CC_IFE_0_FAST_AHB_CLK 53 +#define CAM_CC_IFE_1_CLK 54 +#define CAM_CC_IFE_1_CLK_SRC 55 +#define CAM_CC_IFE_1_DSP_CLK 56 +#define CAM_CC_IFE_1_FAST_AHB_CLK 57 +#define CAM_CC_IFE_2_CLK 58 +#define CAM_CC_IFE_2_CLK_SRC 59 +#define CAM_CC_IFE_2_DSP_CLK 60 +#define CAM_CC_IFE_2_FAST_AHB_CLK 61 +#define CAM_CC_IFE_LITE_AHB_CLK 62 +#define CAM_CC_IFE_LITE_CLK 63 +#define CAM_CC_IFE_LITE_CLK_SRC 64 +#define CAM_CC_IFE_LITE_CPHY_RX_CLK 65 +#define CAM_CC_IFE_LITE_CSID_CLK 66 +#define CAM_CC_IFE_LITE_CSID_CLK_SRC 67 +#define CAM_CC_IPE_NPS_AHB_CLK 68 +#define CAM_CC_IPE_NPS_CLK 69 +#define CAM_CC_IPE_NPS_CLK_SRC 70 +#define CAM_CC_IPE_NPS_FAST_AHB_CLK 71 +#define CAM_CC_IPE_PPS_CLK 72 +#define CAM_CC_IPE_PPS_FAST_AHB_CLK 73 +#define CAM_CC_JPEG_CLK 74 +#define CAM_CC_JPEG_CLK_SRC 75 +#define CAM_CC_MCLK0_CLK 76 +#define CAM_CC_MCLK0_CLK_SRC 77 +#define CAM_CC_MCLK1_CLK 78 +#define CAM_CC_MCLK1_CLK_SRC 79 +#define CAM_CC_MCLK2_CLK 80 +#define CAM_CC_MCLK2_CLK_SRC 81 +#define CAM_CC_MCLK3_CLK 82 +#define CAM_CC_MCLK3_CLK_SRC 83 +#define CAM_CC_MCLK4_CLK 84 +#define CAM_CC_MCLK4_CLK_SRC 85 +#define CAM_CC_MCLK5_CLK 86 +#define CAM_CC_MCLK5_CLK_SRC 87 +#define CAM_CC_MCLK6_CLK 88 +#define CAM_CC_MCLK6_CLK_SRC 89 +#define CAM_CC_MCLK7_CLK 90 +#define CAM_CC_MCLK7_CLK_SRC 91 +#define CAM_CC_PLL0 92 +#define CAM_CC_PLL0_OUT_EVEN 93 +#define CAM_CC_PLL0_OUT_ODD 94 +#define CAM_CC_PLL1 95 +#define CAM_CC_PLL1_OUT_EVEN 96 +#define CAM_CC_PLL2 97 +#define CAM_CC_PLL3 98 +#define CAM_CC_PLL3_OUT_EVEN 99 +#define CAM_CC_PLL4 100 +#define CAM_CC_PLL4_OUT_EVEN 101 +#define CAM_CC_PLL5 102 +#define CAM_CC_PLL5_OUT_EVEN 103 +#define CAM_CC_PLL6 104 +#define CAM_CC_PLL6_OUT_EVEN 105 +#define CAM_CC_PLL7 106 +#define CAM_CC_PLL7_OUT_EVEN 107 +#define CAM_CC_PLL8 108 +#define CAM_CC_PLL8_OUT_EVEN 109 +#define CAM_CC_QDSS_DEBUG_CLK 110 +#define CAM_CC_QDSS_DEBUG_CLK_SRC 111 +#define CAM_CC_QDSS_DEBUG_XO_CLK 112 +#define CAM_CC_SBI_AHB_CLK 113 +#define CAM_CC_SBI_CLK 114 +#define CAM_CC_SFE_0_CLK 115 +#define CAM_CC_SFE_0_CLK_SRC 116 +#define CAM_CC_SFE_0_FAST_AHB_CLK 117 +#define CAM_CC_SFE_1_CLK 118 +#define CAM_CC_SFE_1_CLK_SRC 119 +#define CAM_CC_SFE_1_FAST_AHB_CLK 120 +#define CAM_CC_SLEEP_CLK 121 +#define CAM_CC_SLEEP_CLK_SRC 122 +#define CAM_CC_SLOW_AHB_CLK_SRC 123 +#define CAM_CC_XO_CLK_SRC 124 + +/* CAM_CC resets */ +#define CAM_CC_BPS_BCR 0 +#define CAM_CC_ICP_BCR 1 +#define CAM_CC_IFE_0_BCR 2 +#define CAM_CC_IFE_1_BCR 3 +#define CAM_CC_IFE_2_BCR 4 +#define CAM_CC_IPE_0_BCR 5 +#define CAM_CC_QDSS_DEBUG_BCR 6 +#define CAM_CC_SBI_BCR 7 +#define CAM_CC_SFE_0_BCR 8 +#define CAM_CC_SFE_1_BCR 9 + +/* CAM_CC GDSCRs */ +#define BPS_GDSC 0 +#define IPE_0_GDSC 1 +#define SBI_GDSC 2 +#define IFE_0_GDSC 3 +#define IFE_1_GDSC 4 +#define IFE_2_GDSC 5 +#define SFE_0_GDSC 6 +#define SFE_1_GDSC 7 +#define TITAN_TOP_GDSC 8 + +#endif -- 2.33.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings 2022-03-14 11:42 ` [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings Vladimir Zapolskiy @ 2022-03-14 14:42 ` Rob Herring 2022-04-13 2:53 ` Bjorn Andersson 1 sibling, 0 replies; 5+ messages in thread From: Rob Herring @ 2022-03-14 14:42 UTC (permalink / raw) To: Vladimir Zapolskiy Cc: linux-clk, Michael Turquette, Bjorn Andersson, Stephen Boyd, Rob Herring, Andy Gross, linux-arm-msm, devicetree On Mon, 14 Mar 2022 13:42:10 +0200, Vladimir Zapolskiy wrote: > The change adds device tree bindings for camera clock controller > found on SM8450 SoC. > > Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> > --- > Changes from v1 to v2: > * updated qcom,camcc-sm8450.yaml according to review comments from Rob, > * changed qcom,camcc-sm8450.h license to dual one. > > .../bindings/clock/qcom,camcc-sm8450.yaml | 89 ++++++++++ > include/dt-bindings/clock/qcom,camcc-sm8450.h | 159 ++++++++++++++++++ > 2 files changed, 248 insertions(+) > create mode 100644 Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml > create mode 100644 include/dt-bindings/clock/qcom,camcc-sm8450.h > My bot found errors running 'make DT_CHECKER_FLAGS=-m dt_binding_check' on your patch (DT_CHECKER_FLAGS is new in v5.13): yamllint warnings/errors: dtschema/dtc warnings/errors: Error: Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.example.dts:30.34-35 syntax error FATAL ERROR: Unable to parse input tree make[1]: *** [scripts/Makefile.lib:378: Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.example.dt.yaml] Error 1 make[1]: *** Waiting for unfinished jobs.... make: *** [Makefile:1398: dt_binding_check] Error 2 doc reference errors (make refcheckdocs): See https://patchwork.ozlabs.org/patch/1605035 This check can fail if there are any dependencies. The base for a patch series is generally the most recent rc1. If you already ran 'make dt_binding_check' and didn't see the above error(s), then make sure 'yamllint' is installed and dt-schema is up to date: pip3 install dtschema --upgrade Please check and re-submit. ^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings 2022-03-14 11:42 ` [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings Vladimir Zapolskiy 2022-03-14 14:42 ` Rob Herring @ 2022-04-13 2:53 ` Bjorn Andersson 1 sibling, 0 replies; 5+ messages in thread From: Bjorn Andersson @ 2022-04-13 2:53 UTC (permalink / raw) To: Vladimir Zapolskiy Cc: Rob Herring, Andy Gross, Stephen Boyd, Michael Turquette, devicetree, linux-arm-msm, linux-clk On Mon 14 Mar 06:42 CDT 2022, Vladimir Zapolskiy wrote: > The change adds device tree bindings for camera clock controller > found on SM8450 SoC. > This series looks good to me. I had some very minor suggestions on the driver implementation side, please fix those up and address the DT warning reported by Rob, so we can get an ack from the DT maintainers. Thanks, Bjorn > Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> > --- > Changes from v1 to v2: > * updated qcom,camcc-sm8450.yaml according to review comments from Rob, > * changed qcom,camcc-sm8450.h license to dual one. > > .../bindings/clock/qcom,camcc-sm8450.yaml | 89 ++++++++++ > include/dt-bindings/clock/qcom,camcc-sm8450.h | 159 ++++++++++++++++++ > 2 files changed, 248 insertions(+) > create mode 100644 Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml > create mode 100644 include/dt-bindings/clock/qcom,camcc-sm8450.h > > diff --git a/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml b/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml > new file mode 100644 > index 000000000000..2ea0fc12dd69 > --- /dev/null > +++ b/Documentation/devicetree/bindings/clock/qcom,camcc-sm8450.yaml > @@ -0,0 +1,89 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/clock/qcom,camcc-sm8450.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Qualcomm Camera Clock & Reset Controller Binding for SM8450 > + > +maintainers: > + - Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> > + > +description: | > + Qualcomm camera clock control module which supports the clocks, resets and > + power domains on SM8450. > + > + See also dt-bindings/clock/qcom,camcc-sm8450.h > + > +properties: > + compatible: > + const: qcom,sm8450-camcc > + > + clocks: > + items: > + - description: Camera AHB clock from GCC > + - description: Board XO source > + - description: Board active XO source > + - description: Sleep clock source > + > + clock-names: > + items: > + - const: iface > + - const: bi_tcxo > + - const: bi_tcxo_ao > + - const: sleep_clk > + > + power-domains: > + maxItems: 1 > + description: > + A phandle and PM domain specifier for the MMCX power domain. > + > + required-opps: > + description: > + A phandle to an OPP node describing required MMCX performance point. > + > + '#clock-cells': > + const: 1 > + > + '#reset-cells': > + const: 1 > + > + '#power-domain-cells': > + const: 1 > + > + reg: > + maxItems: 1 > + > +required: > + - compatible > + - reg > + - clocks > + - clock-names > + - power-domains > + - required-opps > + - '#clock-cells' > + - '#reset-cells' > + - '#power-domain-cells' > + > +additionalProperties: false > + > +examples: > + - | > + #include <dt-bindings/clock/qcom,gcc-sm8450.h> > + #include <dt-bindings/clock/qcom,rpmh.h> > + #include <dt-bindings/power/qcom-rpmpd.h> > + clock-controller@ade0000 { > + compatible = "qcom,sm8450-camcc"; > + reg = <0 0xade0000 0 0x20000>; > + clocks = <&gcc GCC_CAMERA_AHB_CLK>, > + <&rpmhcc RPMH_CXO_CLK>, > + <&rpmhcc RPMH_CXO_CLK_A>, > + <&sleep_clk>; > + clock-names = "iface", bi_tcxo", "bi_tcxo_ao", "sleep_clk"; > + power-domains = <&rpmhpd SM8450_MMCX>; > + required-opps = <&rpmhpd_opp_low_svs>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + #power-domain-cells = <1>; > + }; > +... > diff --git a/include/dt-bindings/clock/qcom,camcc-sm8450.h b/include/dt-bindings/clock/qcom,camcc-sm8450.h > new file mode 100644 > index 000000000000..7ff67acf301a > --- /dev/null > +++ b/include/dt-bindings/clock/qcom,camcc-sm8450.h > @@ -0,0 +1,159 @@ > +/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */ > +/* > + * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved. > + */ > + > +#ifndef _DT_BINDINGS_CLK_QCOM_CAM_CC_SM8450_H > +#define _DT_BINDINGS_CLK_QCOM_CAM_CC_SM8450_H > + > +/* CAM_CC clocks */ > +#define CAM_CC_BPS_AHB_CLK 0 > +#define CAM_CC_BPS_CLK 1 > +#define CAM_CC_BPS_CLK_SRC 2 > +#define CAM_CC_BPS_FAST_AHB_CLK 3 > +#define CAM_CC_CAMNOC_AXI_CLK 4 > +#define CAM_CC_CAMNOC_AXI_CLK_SRC 5 > +#define CAM_CC_CAMNOC_DCD_XO_CLK 6 > +#define CAM_CC_CCI_0_CLK 7 > +#define CAM_CC_CCI_0_CLK_SRC 8 > +#define CAM_CC_CCI_1_CLK 9 > +#define CAM_CC_CCI_1_CLK_SRC 10 > +#define CAM_CC_CORE_AHB_CLK 11 > +#define CAM_CC_CPAS_AHB_CLK 12 > +#define CAM_CC_CPAS_BPS_CLK 13 > +#define CAM_CC_CPAS_FAST_AHB_CLK 14 > +#define CAM_CC_CPAS_IFE_0_CLK 15 > +#define CAM_CC_CPAS_IFE_1_CLK 16 > +#define CAM_CC_CPAS_IFE_2_CLK 17 > +#define CAM_CC_CPAS_IFE_LITE_CLK 18 > +#define CAM_CC_CPAS_IPE_NPS_CLK 19 > +#define CAM_CC_CPAS_SBI_CLK 20 > +#define CAM_CC_CPAS_SFE_0_CLK 21 > +#define CAM_CC_CPAS_SFE_1_CLK 22 > +#define CAM_CC_CPHY_RX_CLK_SRC 23 > +#define CAM_CC_CSI0PHYTIMER_CLK 24 > +#define CAM_CC_CSI0PHYTIMER_CLK_SRC 25 > +#define CAM_CC_CSI1PHYTIMER_CLK 26 > +#define CAM_CC_CSI1PHYTIMER_CLK_SRC 27 > +#define CAM_CC_CSI2PHYTIMER_CLK 28 > +#define CAM_CC_CSI2PHYTIMER_CLK_SRC 29 > +#define CAM_CC_CSI3PHYTIMER_CLK 30 > +#define CAM_CC_CSI3PHYTIMER_CLK_SRC 31 > +#define CAM_CC_CSI4PHYTIMER_CLK 32 > +#define CAM_CC_CSI4PHYTIMER_CLK_SRC 33 > +#define CAM_CC_CSI5PHYTIMER_CLK 34 > +#define CAM_CC_CSI5PHYTIMER_CLK_SRC 35 > +#define CAM_CC_CSID_CLK 36 > +#define CAM_CC_CSID_CLK_SRC 37 > +#define CAM_CC_CSID_CSIPHY_RX_CLK 38 > +#define CAM_CC_CSIPHY0_CLK 39 > +#define CAM_CC_CSIPHY1_CLK 40 > +#define CAM_CC_CSIPHY2_CLK 41 > +#define CAM_CC_CSIPHY3_CLK 42 > +#define CAM_CC_CSIPHY4_CLK 43 > +#define CAM_CC_CSIPHY5_CLK 44 > +#define CAM_CC_FAST_AHB_CLK_SRC 45 > +#define CAM_CC_GDSC_CLK 46 > +#define CAM_CC_ICP_AHB_CLK 47 > +#define CAM_CC_ICP_CLK 48 > +#define CAM_CC_ICP_CLK_SRC 49 > +#define CAM_CC_IFE_0_CLK 50 > +#define CAM_CC_IFE_0_CLK_SRC 51 > +#define CAM_CC_IFE_0_DSP_CLK 52 > +#define CAM_CC_IFE_0_FAST_AHB_CLK 53 > +#define CAM_CC_IFE_1_CLK 54 > +#define CAM_CC_IFE_1_CLK_SRC 55 > +#define CAM_CC_IFE_1_DSP_CLK 56 > +#define CAM_CC_IFE_1_FAST_AHB_CLK 57 > +#define CAM_CC_IFE_2_CLK 58 > +#define CAM_CC_IFE_2_CLK_SRC 59 > +#define CAM_CC_IFE_2_DSP_CLK 60 > +#define CAM_CC_IFE_2_FAST_AHB_CLK 61 > +#define CAM_CC_IFE_LITE_AHB_CLK 62 > +#define CAM_CC_IFE_LITE_CLK 63 > +#define CAM_CC_IFE_LITE_CLK_SRC 64 > +#define CAM_CC_IFE_LITE_CPHY_RX_CLK 65 > +#define CAM_CC_IFE_LITE_CSID_CLK 66 > +#define CAM_CC_IFE_LITE_CSID_CLK_SRC 67 > +#define CAM_CC_IPE_NPS_AHB_CLK 68 > +#define CAM_CC_IPE_NPS_CLK 69 > +#define CAM_CC_IPE_NPS_CLK_SRC 70 > +#define CAM_CC_IPE_NPS_FAST_AHB_CLK 71 > +#define CAM_CC_IPE_PPS_CLK 72 > +#define CAM_CC_IPE_PPS_FAST_AHB_CLK 73 > +#define CAM_CC_JPEG_CLK 74 > +#define CAM_CC_JPEG_CLK_SRC 75 > +#define CAM_CC_MCLK0_CLK 76 > +#define CAM_CC_MCLK0_CLK_SRC 77 > +#define CAM_CC_MCLK1_CLK 78 > +#define CAM_CC_MCLK1_CLK_SRC 79 > +#define CAM_CC_MCLK2_CLK 80 > +#define CAM_CC_MCLK2_CLK_SRC 81 > +#define CAM_CC_MCLK3_CLK 82 > +#define CAM_CC_MCLK3_CLK_SRC 83 > +#define CAM_CC_MCLK4_CLK 84 > +#define CAM_CC_MCLK4_CLK_SRC 85 > +#define CAM_CC_MCLK5_CLK 86 > +#define CAM_CC_MCLK5_CLK_SRC 87 > +#define CAM_CC_MCLK6_CLK 88 > +#define CAM_CC_MCLK6_CLK_SRC 89 > +#define CAM_CC_MCLK7_CLK 90 > +#define CAM_CC_MCLK7_CLK_SRC 91 > +#define CAM_CC_PLL0 92 > +#define CAM_CC_PLL0_OUT_EVEN 93 > +#define CAM_CC_PLL0_OUT_ODD 94 > +#define CAM_CC_PLL1 95 > +#define CAM_CC_PLL1_OUT_EVEN 96 > +#define CAM_CC_PLL2 97 > +#define CAM_CC_PLL3 98 > +#define CAM_CC_PLL3_OUT_EVEN 99 > +#define CAM_CC_PLL4 100 > +#define CAM_CC_PLL4_OUT_EVEN 101 > +#define CAM_CC_PLL5 102 > +#define CAM_CC_PLL5_OUT_EVEN 103 > +#define CAM_CC_PLL6 104 > +#define CAM_CC_PLL6_OUT_EVEN 105 > +#define CAM_CC_PLL7 106 > +#define CAM_CC_PLL7_OUT_EVEN 107 > +#define CAM_CC_PLL8 108 > +#define CAM_CC_PLL8_OUT_EVEN 109 > +#define CAM_CC_QDSS_DEBUG_CLK 110 > +#define CAM_CC_QDSS_DEBUG_CLK_SRC 111 > +#define CAM_CC_QDSS_DEBUG_XO_CLK 112 > +#define CAM_CC_SBI_AHB_CLK 113 > +#define CAM_CC_SBI_CLK 114 > +#define CAM_CC_SFE_0_CLK 115 > +#define CAM_CC_SFE_0_CLK_SRC 116 > +#define CAM_CC_SFE_0_FAST_AHB_CLK 117 > +#define CAM_CC_SFE_1_CLK 118 > +#define CAM_CC_SFE_1_CLK_SRC 119 > +#define CAM_CC_SFE_1_FAST_AHB_CLK 120 > +#define CAM_CC_SLEEP_CLK 121 > +#define CAM_CC_SLEEP_CLK_SRC 122 > +#define CAM_CC_SLOW_AHB_CLK_SRC 123 > +#define CAM_CC_XO_CLK_SRC 124 > + > +/* CAM_CC resets */ > +#define CAM_CC_BPS_BCR 0 > +#define CAM_CC_ICP_BCR 1 > +#define CAM_CC_IFE_0_BCR 2 > +#define CAM_CC_IFE_1_BCR 3 > +#define CAM_CC_IFE_2_BCR 4 > +#define CAM_CC_IPE_0_BCR 5 > +#define CAM_CC_QDSS_DEBUG_BCR 6 > +#define CAM_CC_SBI_BCR 7 > +#define CAM_CC_SFE_0_BCR 8 > +#define CAM_CC_SFE_1_BCR 9 > + > +/* CAM_CC GDSCRs */ > +#define BPS_GDSC 0 > +#define IPE_0_GDSC 1 > +#define SBI_GDSC 2 > +#define IFE_0_GDSC 3 > +#define IFE_1_GDSC 4 > +#define IFE_2_GDSC 5 > +#define SFE_0_GDSC 6 > +#define SFE_1_GDSC 7 > +#define TITAN_TOP_GDSC 8 > + > +#endif > -- > 2.33.0 > ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v2 2/7] arm64: dts: qcom: sm8450: Add description of camera clock controller 2022-03-14 11:42 [PATCH v2 0/7] clk: qcom: add camera clock controller driver for SM8450 SoC Vladimir Zapolskiy 2022-03-14 11:42 ` [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings Vladimir Zapolskiy @ 2022-03-14 11:42 ` Vladimir Zapolskiy 1 sibling, 0 replies; 5+ messages in thread From: Vladimir Zapolskiy @ 2022-03-14 11:42 UTC (permalink / raw) To: Rob Herring, Bjorn Andersson Cc: Andy Gross, Stephen Boyd, Michael Turquette, devicetree, linux-arm-msm, linux-clk The change adds description of QCOm SM8450 camera clock controller. Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> --- Changes from v1 to v2: * disabled camcc device tree node by default arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi index 10c25ad2d0c7..62e06874d1a8 100644 --- a/arch/arm64/boot/dts/qcom/sm8450.dtsi +++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi @@ -4,6 +4,7 @@ */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/qcom,camcc-sm8450.h> #include <dt-bindings/clock/qcom,gcc-sm8450.h> #include <dt-bindings/clock/qcom,rpmh.h> #include <dt-bindings/gpio/gpio.h> @@ -672,6 +673,25 @@ usb_1_ssphy: phy@88e9200 { }; }; + camcc: clock-controller@ade0000 { + compatible = "qcom,sm8450-camcc"; + reg = <0 0x0ade0000 0 0x20000>; + status = "disabled"; + clocks = <&gcc GCC_CAMERA_AHB_CLK>, + <&rpmhcc RPMH_CXO_CLK>, + <&rpmhcc RPMH_CXO_CLK_A>, + <&sleep_clk>; + clock-names = "iface", + "bi_tcxo", + "bi_tcxo_ao", + "sleep_clk"; + power-domains = <&rpmhpd SM8450_MMCX>; + required-opps = <&rpmhpd_opp_low_svs>; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + }; + pdc: interrupt-controller@b220000 { compatible = "qcom,sm8450-pdc", "qcom,pdc"; reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>; -- 2.33.0 ^ permalink raw reply related [flat|nested] 5+ messages in thread
end of thread, other threads:[~2022-04-13 2:53 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2022-03-14 11:42 [PATCH v2 0/7] clk: qcom: add camera clock controller driver for SM8450 SoC Vladimir Zapolskiy 2022-03-14 11:42 ` [PATCH v2 1/7] dt-bindings: clock: add QCOM SM8450 camera clock bindings Vladimir Zapolskiy 2022-03-14 14:42 ` Rob Herring 2022-04-13 2:53 ` Bjorn Andersson 2022-03-14 11:42 ` [PATCH v2 2/7] arm64: dts: qcom: sm8450: Add description of camera clock controller Vladimir Zapolskiy
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).