From: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
To: <agross@kernel.org>, <bjorn.andersson@linaro.org>,
<robh+dt@kernel.org>, <linux-arm-msm@vger.kernel.org>,
<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
<quic_rohkumar@quicinc.com>, <srinivas.kandagatla@linaro.org>,
<dianders@chromium.org>, <swboyd@chromium.org>,
<judyhsiao@chromium.org>
Cc: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>,
"Venkata Prasad Potturu" <quic_potturu@quicinc.com>
Subject: [PATCH v9 04/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0 and CRD 2.0
Date: Thu, 21 Apr 2022 20:17:31 +0530 [thread overview]
Message-ID: <1650552459-21077-5-git-send-email-quic_srivasam@quicinc.com> (raw)
In-Reply-To: <1650552459-21077-1-git-send-email-quic_srivasam@quicinc.com>
Add wcd9385 codec node for audio use case on sc7280 based platforms
of revision 3 and 4 (aka CRD 1.0 and 2.0).
Add tlmm gpio property for switching CTIA/OMTP Headset.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Co-developed-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
Signed-off-by: Venkata Prasad Potturu <quic_potturu@quicinc.com>
---
arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts | 8 +++++
arch/arm64/boot/dts/qcom/sc7280-idp.dtsi | 50 ++++++++++++++++++++++++++++++
2 files changed, 58 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
index 344338a..462d655 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
@@ -87,6 +87,14 @@ ap_ts_pen_1v8: &i2c13 {
pins = "gpio51";
};
+&wcd938x {
+ pinctrl-names = "default", "sleep", "us_euro_hs_sel";
+ pinctrl-0 = <&wcd_reset_n>;
+ pinctrl-1 = <&wcd_reset_n_sleep>;
+ pinctrl-2 = <&us_euro_hs_sel>;
+ us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
+
&tlmm {
tp_int_odl: tp-int-odl {
pins = "gpio7";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index 6cb5fc4..b711ad0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -20,6 +20,34 @@
serial1 = &uart7;
};
+ wcd938x: audio-codec-1 {
+ compatible = "qcom,wcd9385-codec";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&wcd_reset_n>;
+ pinctrl-1 = <&wcd_reset_n_sleep>;
+
+ reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ vdd-rxtx-supply = <&vreg_l18b_1p8>;
+ vdd-io-supply = <&vreg_l18b_1p8>;
+ vdd-buck-supply = <&vreg_l17b_1p8>;
+ vdd-mic-bias-supply = <&vreg_bob>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+ 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ #sound-dai-cells = <1>;
+ };
+
gpio-keys {
compatible = "gpio-keys";
label = "gpio-keys";
@@ -678,6 +706,28 @@
function = "gpio";
bias-pull-down;
};
+
+ us_euro_hs_sel: us-euro-hs-sel {
+ pins = "gpio81";
+ function = "gpio";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ wcd_reset_n: wcd-reset-n {
+ pins = "gpio83";
+ function = "gpio";
+ drive-strength = <8>;
+ output-high;
+ };
+
+ wcd_reset_n_sleep: wcd-reset-n-sleep {
+ pins = "gpio83";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ output-low;
+ };
};
&remoteproc_wpss {
--
2.7.4
next prev parent reply other threads:[~2022-04-21 14:49 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-04-21 14:47 [PATCH v9 00/12] Add soundcard support for sc7280 based platforms Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 01/12] arm64: dts: qcom: sc7280: Add nodes for soundwire and va tx rx digital macro codecs Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 02/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 1.0 and CRD 2.0 Srinivasa Rao Mandadapu
2022-04-21 16:17 ` Matthias Kaehlcke
2022-04-22 13:42 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 03/12] arm64: dts: qcom: sc7280: Enable digital codecs and soundwire for CRD 3.0/3.1 Srinivasa Rao Mandadapu
2022-04-21 16:28 ` Matthias Kaehlcke
2022-04-22 13:44 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` Srinivasa Rao Mandadapu [this message]
2022-04-21 16:44 ` [PATCH v9 04/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 1.0 and CRD 2.0 Matthias Kaehlcke
2022-04-21 14:47 ` [PATCH v9 05/12] arm64: dts: qcom: sc7280: Add wcd9385 codec node for CRD 3.0/3.1 Srinivasa Rao Mandadapu
2022-04-21 16:57 ` Matthias Kaehlcke
2022-04-22 13:46 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 06/12] arm64: dts: qcom: sc7280: Add max98360a codec for CRD 1.0 and 2.0 Srinivasa Rao Mandadapu
2022-04-21 17:00 ` Matthias Kaehlcke
2022-04-21 14:47 ` [PATCH v9 07/12] arm64: dts: qcom: sc7280: Add max98360a codec node for CRD 3.0/3.1 Srinivasa Rao Mandadapu
2022-04-21 17:11 ` Matthias Kaehlcke
2022-04-22 13:48 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 08/12] arm64: dts: qcom: sc7280: Add lpass cpu node Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 09/12] arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 1.0 and CRD 2.0 Srinivasa Rao Mandadapu
2022-04-21 17:13 ` Matthias Kaehlcke
2022-04-22 13:49 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 10/12] arm64: dts: qcom: sc7280: Enable lpass cpu node for CRD 3.0/3.1 Srinivasa Rao Mandadapu
2022-04-21 17:18 ` Matthias Kaehlcke
2022-04-21 14:47 ` [PATCH v9 11/12] arm64: dts: qcom: sc7280: Add sound node for CRD 1.0 and CRD 2.0 Srinivasa Rao Mandadapu
2022-04-21 17:56 ` Matthias Kaehlcke
2022-04-22 13:51 ` Srinivasa Rao Mandadapu
2022-04-21 14:47 ` [PATCH v9 12/12] arm64: dts: qcom: sc7280: Add sound node for CRD 3.0/3.1 Srinivasa Rao Mandadapu
2022-04-21 18:03 ` Matthias Kaehlcke
2022-04-22 13:52 ` Srinivasa Rao Mandadapu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1650552459-21077-5-git-send-email-quic_srivasam@quicinc.com \
--to=quic_srivasam@quicinc.com \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=judyhsiao@chromium.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=quic_potturu@quicinc.com \
--cc=quic_rohkumar@quicinc.com \
--cc=robh+dt@kernel.org \
--cc=srinivas.kandagatla@linaro.org \
--cc=swboyd@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).