[PATCH net-next v4 0/9] net: lan969x: add RGMII support

[PATCH net-next v4 0/9] net: lan969x: add RGMII support

[Daniel Machon]

== Description:

This series is the fourth of a multi-part series, that prepares and adds
support for the new lan969x switch driver.

The upstreaming efforts is split into multiple series (might change a
bit as we go along):

        1) Prepare the Sparx5 driver for lan969x (merged)

        2) Add support for lan969x (same basic features as Sparx5
           provides excl. FDMA and VCAP, merged).

        3) Add lan969x VCAP functionality (merged).

    --> 4) Add RGMII support.

        5) Add FDMA support.

== RGMII support:

The lan969x switch device includes two RGMII port interfaces (port 28
and 29) supporting data speeds of 1 Gbps, 100 Mbps and 10 Mbps.

== Patch breakdown:

Patch #1 does some preparation work.

Patch #2 adds new function: is_port_rgmii() to the match data ops.

Patch #3 uses the is_port_rgmii() in a number of places.

Patch #4 makes sure that we do not configure an RGMII device as a
         low-speed device, when doing a port config.

Patch #5 makes sure we only return the PCS if the port mode requires
         it.

Patch #6 adds checks for RGMII PHY modes in sparx5_verify_speeds().

Patch #7 adds registers required to configure RGMII.

Patch #8 adds RGMII implementation.

Patch #9 documents RGMII delays in the dt-bindings.

Details are in the commit description of the individual patches

To: UNGLinuxDriver@microchip.com
To: Andrew Lunn <andrew+netdev@lunn.ch>
To: David S. Miller <davem@davemloft.net>
To: Eric Dumazet <edumazet@google.com>
To: Jakub Kicinski <kuba@kernel.org>
To: Paolo Abeni <pabeni@redhat.com>
To: Lars Povlsen <lars.povlsen@microchip.com>
To: Steen Hegelund <Steen.Hegelund@microchip.com>
To: Horatiu Vultur <horatiu.vultur@microchip.com>
To: Russell King <linux@armlinux.org.uk>
To: jacob.e.keller@intel.com
To: robh@kernel.org
To: krzk+dt@kernel.org
To: conor+dt@kernel.org
Cc: devicetree@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: robert.marko@sartura.hr

Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
Changes in v4:

- Split patch #4 in v3 into two patches, where the new patch #5 handles
  PCS selection, by returning the PCS only for ports that require it.

- Got rid of the '|' symbol for {rx,tx}-internal-delay-ps property
  description in the dt-bindings (patch #9).

- Link to v3: https://lore.kernel.org/r/20241118-sparx5-lan969x-switch-driver-4-v3-0-3cefee5e7e3a@microchip.com

Changes in v3:

v2 was kindly tested by Robert Marko. Not carrying the tag to v3 since
we have changes to the handling of the delays.

- Modified lan969x_rgmii_delay_config() to not apply any MAC delay when
  the {rx,tx}-internal-delay-ps properties are missing or set to 0
  (patch #7).

- Removed 'required' constraint from {rx-tx}-internal-delay-ps
  properties. Also added description and default value (Patch #8).

- Link to v2: https://lore.kernel.org/r/20241113-sparx5-lan969x-switch-driver-4-v2-0-0db98ac096d1@microchip.com

Changes in v2:

  Most changes are in patch #7. RGMII implementation has been moved to
  it's own file lan969x_rgmii.c.

  Details:

    - Use ETH_P_8021Q and ETH_P_8021AD instead of the Sparx5 provided
      equivalents (patch #7).
    - Configure MAC delays through "{rx,tx}-internal-delay-ps"
      properties (patch #7).
    - Add selectors for all the phase shifts that the hardware supports
      (instead of only 2.0 ns, patch #7).
    - Add selectors for all the port speeds (instead of only 1000 mbps.)
    - Document RGMII delays in dt-bindings.

  - Link to v1: https://lore.kernel.org/r/20241106-sparx5-lan969x-switch-driver-4-v1-0-f7f7316436bd@microchip.com

---
Daniel Machon (9):
      net: sparx5: do some preparation work
      net: sparx5: add function for RGMII port check
      net: sparx5: use is_port_rgmii() throughout
      net: sparx5: skip low-speed configuration when port is RGMII
      net: sparx5: only return PCS for modes that require it
      net: sparx5: verify RGMII speeds
      net: lan969x: add RGMII registers
      net: lan969x: add RGMII implementation
      dt-bindings: net: sparx5: document RGMII delays

 .../bindings/net/microchip,sparx5-switch.yaml      |  18 ++
 drivers/net/ethernet/microchip/sparx5/Makefile     |   3 +-
 .../ethernet/microchip/sparx5/lan969x/lan969x.c    |   5 +
 .../ethernet/microchip/sparx5/lan969x/lan969x.h    |  10 +
 .../microchip/sparx5/lan969x/lan969x_rgmii.c       | 224 +++++++++++++++++++++
 .../net/ethernet/microchip/sparx5/sparx5_main.c    |  29 ++-
 .../net/ethernet/microchip/sparx5/sparx5_main.h    |   3 +
 .../ethernet/microchip/sparx5/sparx5_main_regs.h   | 145 +++++++++++++
 .../net/ethernet/microchip/sparx5/sparx5_phylink.c |  14 +-
 .../net/ethernet/microchip/sparx5/sparx5_port.c    |  57 ++++--
 .../net/ethernet/microchip/sparx5/sparx5_port.h    |   5 +
 11 files changed, 484 insertions(+), 29 deletions(-)
---
base-commit: 2c27c7663390d28bc71e97500eb68e0ce2a7223f
change-id: 20241104-sparx5-lan969x-switch-driver-4-d59b7820485a

Best regards,
-- 
Daniel Machon <daniel.machon@microchip.com>

[PATCH net-next v4 1/9] net: sparx5: do some preparation work

[Daniel Machon]

The sparx5_port_init() does initial configuration of a variety of
different features and options for each port. Some are shared for all
types of devices, some are not. As it is now, common configuration is
done after configuration of low-speed devices. This will not work when
adding RGMII support in a subsequent patch.

In preparation for lan969x RGMII support, move a block of code, that
configures 2g5 devices, down. This ensures that the configuration common
to all devices is done before configuration of 2g5, 5g, 10g and 25g
devices.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 .../net/ethernet/microchip/sparx5/sparx5_port.c    | 36 +++++++++++-----------
 1 file changed, 18 insertions(+), 18 deletions(-)

diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index f9d1a6bb9bff..f39bf4878e11 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -1067,24 +1067,6 @@ int sparx5_port_init(struct sparx5 *sparx5,
 	if (err)
 		return err;
 
-	/* Configure MAC vlan awareness */
-	err = sparx5_port_max_tags_set(sparx5, port);
-	if (err)
-		return err;
-
-	/* Set Max Length */
-	spx5_rmw(DEV2G5_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
-		 DEV2G5_MAC_MAXLEN_CFG_MAX_LEN,
-		 sparx5,
-		 DEV2G5_MAC_MAXLEN_CFG(port->portno));
-
-	/* 1G/2G5: Signal Detect configuration */
-	spx5_wr(DEV2G5_PCS1G_SD_CFG_SD_POL_SET(sd_pol) |
-		DEV2G5_PCS1G_SD_CFG_SD_SEL_SET(sd_sel) |
-		DEV2G5_PCS1G_SD_CFG_SD_ENA_SET(sd_ena),
-		sparx5,
-		DEV2G5_PCS1G_SD_CFG(port->portno));
-
 	/* Set Pause WM hysteresis */
 	spx5_rmw(QSYS_PAUSE_CFG_PAUSE_START_SET(pause_start) |
 		 QSYS_PAUSE_CFG_PAUSE_STOP_SET(pause_stop) |
@@ -1108,6 +1090,24 @@ int sparx5_port_init(struct sparx5 *sparx5,
 		 ANA_CL_FILTER_CTRL_FILTER_SMAC_MC_DIS,
 		 sparx5, ANA_CL_FILTER_CTRL(port->portno));
 
+	/* Configure MAC vlan awareness */
+	err = sparx5_port_max_tags_set(sparx5, port);
+	if (err)
+		return err;
+
+	/* Set Max Length */
+	spx5_rmw(DEV2G5_MAC_MAXLEN_CFG_MAX_LEN_SET(ETH_MAXLEN),
+		 DEV2G5_MAC_MAXLEN_CFG_MAX_LEN,
+		 sparx5,
+		 DEV2G5_MAC_MAXLEN_CFG(port->portno));
+
+	/* 1G/2G5: Signal Detect configuration */
+	spx5_wr(DEV2G5_PCS1G_SD_CFG_SD_POL_SET(sd_pol) |
+		DEV2G5_PCS1G_SD_CFG_SD_SEL_SET(sd_sel) |
+		DEV2G5_PCS1G_SD_CFG_SD_ENA_SET(sd_ena),
+		sparx5,
+		DEV2G5_PCS1G_SD_CFG(port->portno));
+
 	if (conf->portmode == PHY_INTERFACE_MODE_QSGMII ||
 	    conf->portmode == PHY_INTERFACE_MODE_SGMII) {
 		err = sparx5_serdes_set(sparx5, port, conf);

-- 
2.34.1

[PATCH net-next v4 2/9] net: sparx5: add function for RGMII port check

[Daniel Machon]

The lan969x device contains two RGMII port interfaces, sitting at port
28 and 29. Add function: is_port_rgmii() to the match data ops, that
checks if a given port is an RGMII port or not. For Sparx5, this
function always returns false.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c | 1 +
 drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h | 5 +++++
 drivers/net/ethernet/microchip/sparx5/sparx5_main.c     | 1 +
 drivers/net/ethernet/microchip/sparx5/sparx5_main.h     | 1 +
 drivers/net/ethernet/microchip/sparx5/sparx5_port.h     | 5 +++++
 5 files changed, 13 insertions(+)

diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
index c2afa2176b08..76f0c8635eb9 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
@@ -329,6 +329,7 @@ static const struct sparx5_ops lan969x_ops = {
 	.is_port_5g              = &lan969x_port_is_5g,
 	.is_port_10g             = &lan969x_port_is_10g,
 	.is_port_25g             = &lan969x_port_is_25g,
+	.is_port_rgmii           = &lan969x_port_is_rgmii,
 	.get_port_dev_index      = &lan969x_port_dev_mapping,
 	.get_port_dev_bit        = &lan969x_get_dev_mode_bit,
 	.get_hsch_max_group_rate = &lan969x_get_hsch_max_group_rate,
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
index 2489d0d32dfd..4b91c47d6d21 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
@@ -59,6 +59,11 @@ static inline bool lan969x_port_is_25g(int portno)
 	return false;
 }
 
+static inline bool lan969x_port_is_rgmii(int portno)
+{
+	return portno == 28 || portno == 29;
+}
+
 /* lan969x_calendar.c */
 int lan969x_dsm_calendar_calc(struct sparx5 *sparx5, u32 taxi,
 			      struct sparx5_calendar_data *data);
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
index f61aa15beab7..4be717ba7d37 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
@@ -1072,6 +1072,7 @@ static const struct sparx5_ops sparx5_ops = {
 	.is_port_5g              = &sparx5_port_is_5g,
 	.is_port_10g             = &sparx5_port_is_10g,
 	.is_port_25g             = &sparx5_port_is_25g,
+	.is_port_rgmii           = &sparx5_port_is_rgmii,
 	.get_port_dev_index      = &sparx5_port_dev_mapping,
 	.get_port_dev_bit        = &sparx5_port_dev_mapping,
 	.get_hsch_max_group_rate = &sparx5_get_hsch_max_group_rate,
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
index d5dd953b0a71..c58d7841638e 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
@@ -313,6 +313,7 @@ struct sparx5_ops {
 	bool (*is_port_5g)(int portno);
 	bool (*is_port_10g)(int portno);
 	bool (*is_port_25g)(int portno);
+	bool (*is_port_rgmii)(int portno);
 	u32  (*get_port_dev_index)(struct sparx5 *sparx5, int port);
 	u32  (*get_port_dev_bit)(struct sparx5 *sparx5, int port);
 	u32  (*get_hsch_max_group_rate)(int grp);
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.h b/drivers/net/ethernet/microchip/sparx5/sparx5_port.h
index 9b9bcc6834bc..c8a37468a3d1 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.h
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.h
@@ -40,6 +40,11 @@ static inline bool sparx5_port_is_25g(int portno)
 	return portno >= 56 && portno <= 63;
 }
 
+static inline bool sparx5_port_is_rgmii(int portno)
+{
+	return false;
+}
+
 static inline u32 sparx5_to_high_dev(struct sparx5 *sparx5, int port)
 {
 	const struct sparx5_ops *ops = sparx5->data->ops;

-- 
2.34.1

[PATCH net-next v4 3/9] net: sparx5: use is_port_rgmii() throughout

[Daniel Machon]

Now that we can check if a given port is an RGMII port, use it in the
following cases:

 - To set RGMII PHY modes for RGMII port devices.

 - To avoid checking for a SerDes node in the devicetree, when the port
   is an RGMII port.

 - To bail out of sparx5_port_init() when the common configuration is
   done.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 .../net/ethernet/microchip/sparx5/sparx5_main.c    | 28 +++++++++++++++-------
 .../net/ethernet/microchip/sparx5/sparx5_port.c    |  3 +++
 2 files changed, 23 insertions(+), 8 deletions(-)

diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
index 4be717ba7d37..e68277c38adc 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.c
@@ -313,10 +313,13 @@ static int sparx5_create_port(struct sparx5 *sparx5,
 			      struct initial_port_config *config)
 {
 	struct sparx5_port *spx5_port;
+	const struct sparx5_ops *ops;
 	struct net_device *ndev;
 	struct phylink *phylink;
 	int err;
 
+	ops = sparx5->data->ops;
+
 	ndev = sparx5_create_netdev(sparx5, config->portno);
 	if (IS_ERR(ndev)) {
 		dev_err(sparx5->dev, "Could not create net device: %02u\n",
@@ -357,6 +360,9 @@ static int sparx5_create_port(struct sparx5 *sparx5,
 		MAC_SYM_PAUSE | MAC_10 | MAC_100 | MAC_1000FD |
 		MAC_2500FD | MAC_5000FD | MAC_10000FD | MAC_25000FD;
 
+	if (ops->is_port_rgmii(spx5_port->portno))
+		phy_interface_set_rgmii(spx5_port->phylink_config.supported_interfaces);
+
 	__set_bit(PHY_INTERFACE_MODE_SGMII,
 		  spx5_port->phylink_config.supported_interfaces);
 	__set_bit(PHY_INTERFACE_MODE_QSGMII,
@@ -830,6 +836,7 @@ static int mchp_sparx5_probe(struct platform_device *pdev)
 	struct initial_port_config *configs, *config;
 	struct device_node *np = pdev->dev.of_node;
 	struct device_node *ports, *portnp;
+	const struct sparx5_ops *ops;
 	struct reset_control *reset;
 	struct sparx5 *sparx5;
 	int idx = 0, err = 0;
@@ -851,6 +858,7 @@ static int mchp_sparx5_probe(struct platform_device *pdev)
 		return -EINVAL;
 
 	regs = sparx5->data->regs;
+	ops = sparx5->data->ops;
 
 	/* Do switch core reset if available */
 	reset = devm_reset_control_get_optional_shared(&pdev->dev, "switch");
@@ -880,7 +888,7 @@ static int mchp_sparx5_probe(struct platform_device *pdev)
 
 	for_each_available_child_of_node(ports, portnp) {
 		struct sparx5_port_config *conf;
-		struct phy *serdes;
+		struct phy *serdes = NULL;
 		u32 portno;
 
 		err = of_property_read_u32(portnp, "reg", &portno);
@@ -910,13 +918,17 @@ static int mchp_sparx5_probe(struct platform_device *pdev)
 			conf->sd_sgpio = ~0;
 		else
 			sparx5->sd_sgpio_remapping = true;
-		serdes = devm_of_phy_get(sparx5->dev, portnp, NULL);
-		if (IS_ERR(serdes)) {
-			err = dev_err_probe(sparx5->dev, PTR_ERR(serdes),
-					    "port %u: missing serdes\n",
-					    portno);
-			of_node_put(portnp);
-			goto cleanup_config;
+		/* There is no SerDes node for RGMII ports. */
+		if (!ops->is_port_rgmii(portno)) {
+			serdes = devm_of_phy_get(sparx5->dev, portnp, NULL);
+			if (IS_ERR(serdes)) {
+				err = dev_err_probe(sparx5->dev,
+						    PTR_ERR(serdes),
+						    "port %u: missing serdes\n",
+						    portno);
+				of_node_put(portnp);
+				goto cleanup_config;
+			}
 		}
 		config->portno = portno;
 		config->node = portnp;
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index f39bf4878e11..996dc4343019 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -1090,6 +1090,9 @@ int sparx5_port_init(struct sparx5 *sparx5,
 		 ANA_CL_FILTER_CTRL_FILTER_SMAC_MC_DIS,
 		 sparx5, ANA_CL_FILTER_CTRL(port->portno));
 
+	if (ops->is_port_rgmii(port->portno))
+		return 0; /* RGMII device - nothing more to configure */
+
 	/* Configure MAC vlan awareness */
 	err = sparx5_port_max_tags_set(sparx5, port);
 	if (err)

-- 
2.34.1

[PATCH net-next v4 4/9] net: sparx5: skip low-speed configuration when port is RGMII

[Daniel Machon]

When doing a port config, we configure low-speed port devices, among
other things. We have a check to ensure, that the device is indeed a
low-speed device, an not a high-speed device. Add an additional check,
to ensure that the device is not an RGMII device.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 drivers/net/ethernet/microchip/sparx5/sparx5_port.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index 996dc4343019..0a1374422ccb 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -994,6 +994,7 @@ int sparx5_port_config(struct sparx5 *sparx5,
 		       struct sparx5_port *port,
 		       struct sparx5_port_config *conf)
 {
+	bool rgmii = phy_interface_mode_is_rgmii(conf->phy_mode);
 	bool high_speed_dev = sparx5_is_baser(conf->portmode);
 	const struct sparx5_ops *ops = sparx5->data->ops;
 	int err, urgency, stop_wm;
@@ -1003,7 +1004,7 @@ int sparx5_port_config(struct sparx5 *sparx5,
 		return err;
 
 	/* high speed device is already configured */
-	if (!high_speed_dev)
+	if (!rgmii && !high_speed_dev)
 		sparx5_port_config_low_set(sparx5, port, conf);
 
 	/* Configure flow control */

-- 
2.34.1

[PATCH net-next v4 5/9] net: sparx5: only return PCS for modes that require it

[Daniel Machon]

The RGMII ports have no PCS to configure. Make sure we only return the
PCS for port modes that require it.

Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c b/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
index f8562c1a894d..035d2f1bea0d 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_phylink.c
@@ -32,7 +32,19 @@ sparx5_phylink_mac_select_pcs(struct phylink_config *config,
 {
 	struct sparx5_port *port = netdev_priv(to_net_dev(config->dev));
 
-	return &port->phylink_pcs;
+	/* Return the PCS for all the modes that require it. */
+	switch (interface) {
+	case PHY_INTERFACE_MODE_SGMII:
+	case PHY_INTERFACE_MODE_QSGMII:
+	case PHY_INTERFACE_MODE_1000BASEX:
+	case PHY_INTERFACE_MODE_2500BASEX:
+	case PHY_INTERFACE_MODE_5GBASER:
+	case PHY_INTERFACE_MODE_10GBASER:
+	case PHY_INTERFACE_MODE_25GBASER:
+		return &port->phylink_pcs;
+	default:
+		return NULL;
+	}
 }
 
 static void sparx5_phylink_mac_config(struct phylink_config *config,

-- 
2.34.1

[PATCH net-next v4 6/9] net: sparx5: verify RGMII speeds

[Daniel Machon]

When doing a port config, we verify the port speed against the PHY mode
and supported speeds of that PHY mode. Add checks for the four RGMII phy
modes: RGMII, RGMII_ID, RGMII_TXID and RGMII_RXID.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 drivers/net/ethernet/microchip/sparx5/sparx5_port.c | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index 0a1374422ccb..86d6c9e9ec7c 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -257,6 +257,15 @@ static int sparx5_port_verify_speed(struct sparx5 *sparx5,
 		     conf->speed != SPEED_25000))
 			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
 		break;
+	case PHY_INTERFACE_MODE_RGMII:
+	case PHY_INTERFACE_MODE_RGMII_ID:
+	case PHY_INTERFACE_MODE_RGMII_TXID:
+	case PHY_INTERFACE_MODE_RGMII_RXID:
+		if (conf->speed != SPEED_1000 &&
+		    conf->speed != SPEED_100 &&
+		    conf->speed != SPEED_10)
+			return sparx5_port_error(port, conf, SPX5_PERR_SPEED);
+		break;
 	default:
 		return sparx5_port_error(port, conf, SPX5_PERR_IFTYPE);
 	}

-- 
2.34.1

[PATCH net-next v4 7/9] net: lan969x: add RGMII registers

[Daniel Machon]

Configuration of RGMII is done by configuring the GPIO and clock
settings in the HSIOWRAP target, and configuring the RGMII port devices
in the DEVRGMII target. Both targets contain registers replicated for
the number of RGMII port devices, which is two.

Add said targets and register macros required to configure RGMII.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 .../ethernet/microchip/sparx5/lan969x/lan969x.c    |   3 +
 .../ethernet/microchip/sparx5/sparx5_main_regs.h   | 145 +++++++++++++++++++++
 2 files changed, 148 insertions(+)

diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
index 76f0c8635eb9..be49a99556fe 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
@@ -90,9 +90,12 @@ static const struct sparx5_main_io_resource lan969x_main_iomap[] =  {
 	{ TARGET_DEV2G5 + 27,         0x30d8000, 1 }, /* 0xe30d8000 */
 	{ TARGET_DEV10G +  9,         0x30dc000, 1 }, /* 0xe30dc000 */
 	{ TARGET_PCS10G_BR +  9,      0x30e0000, 1 }, /* 0xe30e0000 */
+	{ TARGET_DEVRGMII,            0x30e4000, 1 }, /* 0xe30e4000 */
+	{ TARGET_DEVRGMII +  1,       0x30e8000, 1 }, /* 0xe30e8000 */
 	{ TARGET_DSM,                 0x30ec000, 1 }, /* 0xe30ec000 */
 	{ TARGET_PORT_CONF,           0x30f0000, 1 }, /* 0xe30f0000 */
 	{ TARGET_ASM,                 0x3200000, 1 }, /* 0xe3200000 */
+	{ TARGET_HSIO_WRAP,           0x3408000, 1 }, /* 0xe3408000 */
 };
 
 static struct sparx5_sdlb_group lan969x_sdlb_groups[LAN969X_SDLB_GRP_CNT] = {
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main_regs.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main_regs.h
index 561344f19062..d9ef4ef137b8 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main_regs.h
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main_regs.h
@@ -37,6 +37,7 @@ enum sparx5_target {
 	TARGET_FDMA = 117,
 	TARGET_GCB = 118,
 	TARGET_HSCH = 119,
+	TARGET_HSIO_WRAP = 120,
 	TARGET_LRN = 122,
 	TARGET_PCEP = 129,
 	TARGET_PCS10G_BR = 132,
@@ -54,6 +55,7 @@ enum sparx5_target {
 	TARGET_VCAP_SUPER = 326,
 	TARGET_VOP = 327,
 	TARGET_XQS = 331,
+	TARGET_DEVRGMII = 392,
 	NUM_TARGETS = 517
 };
 
@@ -5367,6 +5369,69 @@ extern const struct sparx5_regs *regs;
 #define HSCH_TAS_STATEMACHINE_CFG_REVISIT_DLY_GET(x)\
 	FIELD_GET(HSCH_TAS_STATEMACHINE_CFG_REVISIT_DLY, x)
 
+/* LAN969X ONLY */
+/* HSIOWRAP:XMII_CFG:XMII_CFG */
+#define HSIO_WRAP_XMII_CFG(g)                                                  \
+	__REG(TARGET_HSIO_WRAP, 0, 1, 116, g, 2, 20, 0, 0, 1, 4)
+
+#define HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG         GENMASK(2, 1)
+#define HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG_SET(x)\
+	FIELD_PREP(HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG, x)
+#define HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG_GET(x)\
+	FIELD_GET(HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG, x)
+
+/* LAN969X ONLY */
+/* HSIOWRAP:XMII_CFG:RGMII_CFG */
+#define HSIO_WRAP_RGMII_CFG(g)                                                 \
+	__REG(TARGET_HSIO_WRAP, 0, 1, 116, g, 2, 20, 4, 0, 1, 4)
+
+#define HSIO_WRAP_RGMII_CFG_TX_CLK_CFG           GENMASK(4, 2)
+#define HSIO_WRAP_RGMII_CFG_TX_CLK_CFG_SET(x)\
+	FIELD_PREP(HSIO_WRAP_RGMII_CFG_TX_CLK_CFG, x)
+#define HSIO_WRAP_RGMII_CFG_TX_CLK_CFG_GET(x)\
+	FIELD_GET(HSIO_WRAP_RGMII_CFG_TX_CLK_CFG, x)
+
+#define HSIO_WRAP_RGMII_CFG_RGMII_TX_RST         BIT(1)
+#define HSIO_WRAP_RGMII_CFG_RGMII_TX_RST_SET(x)\
+	FIELD_PREP(HSIO_WRAP_RGMII_CFG_RGMII_TX_RST, x)
+#define HSIO_WRAP_RGMII_CFG_RGMII_TX_RST_GET(x)\
+	FIELD_GET(HSIO_WRAP_RGMII_CFG_RGMII_TX_RST, x)
+
+#define HSIO_WRAP_RGMII_CFG_RGMII_RX_RST         BIT(0)
+#define HSIO_WRAP_RGMII_CFG_RGMII_RX_RST_SET(x)\
+	FIELD_PREP(HSIO_WRAP_RGMII_CFG_RGMII_RX_RST, x)
+#define HSIO_WRAP_RGMII_CFG_RGMII_RX_RST_GET(x)\
+	FIELD_GET(HSIO_WRAP_RGMII_CFG_RGMII_RX_RST, x)
+
+/* LAN969X ONLY */
+/* HSIOWRAP:XMII_CFG:DLL_CFG */
+#define HSIO_WRAP_DLL_CFG(g, r)                                                \
+	__REG(TARGET_HSIO_WRAP, 0, 1, 116, g, 2, 20, 12, r, 2, 4)
+
+#define HSIO_WRAP_DLL_CFG_DLL_ENA                BIT(19)
+#define HSIO_WRAP_DLL_CFG_DLL_ENA_SET(x)\
+	FIELD_PREP(HSIO_WRAP_DLL_CFG_DLL_ENA, x)
+#define HSIO_WRAP_DLL_CFG_DLL_ENA_GET(x)\
+	FIELD_GET(HSIO_WRAP_DLL_CFG_DLL_ENA, x)
+
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_ENA            BIT(18)
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_SET(x)\
+	FIELD_PREP(HSIO_WRAP_DLL_CFG_DLL_CLK_ENA, x)
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_GET(x)\
+	FIELD_GET(HSIO_WRAP_DLL_CFG_DLL_CLK_ENA, x)
+
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_SEL            GENMASK(17, 15)
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_SET(x)\
+	FIELD_PREP(HSIO_WRAP_DLL_CFG_DLL_CLK_SEL, x)
+#define HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_GET(x)\
+	FIELD_GET(HSIO_WRAP_DLL_CFG_DLL_CLK_SEL, x)
+
+#define HSIO_WRAP_DLL_CFG_DLL_RST                BIT(0)
+#define HSIO_WRAP_DLL_CFG_DLL_RST_SET(x)\
+	FIELD_PREP(HSIO_WRAP_DLL_CFG_DLL_RST, x)
+#define HSIO_WRAP_DLL_CFG_DLL_RST_GET(x)\
+	FIELD_GET(HSIO_WRAP_DLL_CFG_DLL_RST, x)
+
 /* LRN:COMMON:COMMON_ACCESS_CTRL */
 #define LRN_COMMON_ACCESS_CTRL                                                 \
 	__REG(TARGET_LRN, 0, 1, 0, 0, 1, 72, 0, 0, 1, 4)
@@ -8110,4 +8175,84 @@ extern const struct sparx5_regs *regs;
 #define XQS_CNT(g)                                                             \
 	__REG(TARGET_XQS, 0, 1, 0, g, 1024, 4, 0, 0, 1, 4)
 
+/* LAN969X ONLY */
+/* DEV1G:DEV_CFG_STATUS:DEV_RST_CTRL */
+#define DEVRGMII_DEV_RST_CTRL(t)                                               \
+	__REG(TARGET_DEVRGMII, t, 2, 0, 0, 1, 36, 0, 0, 1, 4)
+
+#define DEVRGMII_DEV_RST_CTRL_SPEED_SEL          GENMASK(22, 20)
+#define DEVRGMII_DEV_RST_CTRL_SPEED_SEL_SET(x)\
+	FIELD_PREP(DEVRGMII_DEV_RST_CTRL_SPEED_SEL, x)
+#define DEVRGMII_DEV_RST_CTRL_SPEED_SEL_GET(x)\
+	FIELD_GET(DEVRGMII_DEV_RST_CTRL_SPEED_SEL, x)
+
+/* LAN969X ONLY */
+/* DEV1G:MAC_CFG_STATUS:MAC_ENA_CFG */
+#define DEVRGMII_MAC_ENA_CFG(t)                                                \
+	__REG(TARGET_DEVRGMII, t, 2, 36, 0, 1, 36, 0, 0, 1, 4)
+
+#define DEVRGMII_MAC_ENA_CFG_RX_ENA              BIT(4)
+#define DEVRGMII_MAC_ENA_CFG_RX_ENA_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_ENA_CFG_RX_ENA, x)
+#define DEVRGMII_MAC_ENA_CFG_RX_ENA_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_ENA_CFG_RX_ENA, x)
+
+#define DEVRGMII_MAC_ENA_CFG_TX_ENA              BIT(0)
+#define DEVRGMII_MAC_ENA_CFG_TX_ENA_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_ENA_CFG_TX_ENA, x)
+#define DEVRGMII_MAC_ENA_CFG_TX_ENA_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_ENA_CFG_TX_ENA, x)
+
+/* LAN969X ONLY */
+/* DEV1G:MAC_CFG_STATUS:MAC_TAGS_CFG */
+#define DEVRGMII_MAC_TAGS_CFG(t)                                               \
+	__REG(TARGET_DEVRGMII, t, 2, 36, 0, 1, 36, 12, 0, 1, 4)
+
+#define DEVRGMII_MAC_TAGS_CFG_TAG_ID             GENMASK(31, 16)
+#define DEVRGMII_MAC_TAGS_CFG_TAG_ID_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_TAGS_CFG_TAG_ID, x)
+#define DEVRGMII_MAC_TAGS_CFG_TAG_ID_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_TAGS_CFG_TAG_ID, x)
+
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA   BIT(3)
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA, x)
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA, x)
+
+#define DEVRGMII_MAC_TAGS_CFG_PB_ENA             GENMASK(2, 1)
+#define DEVRGMII_MAC_TAGS_CFG_PB_ENA_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_TAGS_CFG_PB_ENA, x)
+#define DEVRGMII_MAC_TAGS_CFG_PB_ENA_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_TAGS_CFG_PB_ENA, x)
+
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA       BIT(0)
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA, x)
+#define DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA, x)
+
+/* LAN969X ONLY */
+/* DEV1G:MAC_CFG_STATUS:MAC_IFG_CFG */
+#define DEVRGMII_MAC_IFG_CFG(t)                                                \
+	__REG(TARGET_DEVRGMII, t, 2, 36, 0, 1, 36, 24, 0, 1, 4)
+
+#define DEVRGMII_MAC_IFG_CFG_TX_IFG              GENMASK(12, 8)
+#define DEVRGMII_MAC_IFG_CFG_TX_IFG_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_IFG_CFG_TX_IFG, x)
+#define DEVRGMII_MAC_IFG_CFG_TX_IFG_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_IFG_CFG_TX_IFG, x)
+
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG2             GENMASK(7, 4)
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG2_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_IFG_CFG_RX_IFG2, x)
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG2_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_IFG_CFG_RX_IFG2, x)
+
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG1             GENMASK(3, 0)
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG1_SET(x)\
+	FIELD_PREP(DEVRGMII_MAC_IFG_CFG_RX_IFG1, x)
+#define DEVRGMII_MAC_IFG_CFG_RX_IFG1_GET(x)\
+	FIELD_GET(DEVRGMII_MAC_IFG_CFG_RX_IFG1, x)
+
 #endif /* _SPARX5_MAIN_REGS_H_ */

-- 
2.34.1

[PATCH net-next v4 8/9] net: lan969x: add RGMII implementation

[Daniel Machon]

The lan969x switch device includes two RGMII port interfaces (port 28
and 29) supporting data speeds of 1 Gbps, 100 Mbps and 10 Mbps. MAC
level delays are configurable through the HSIO_WRAP target, by choosing
a phase shift selector, corresponding to a certain time delay in nano
seconds.

Add new file: lan969x_rgmii.c that contains the implementation for
configuring the RGMII port devices. MAC level delays are configured
using the "{rx,tx}-internal-delay-ps" properties. These properties must
be specified independently of the phy-mode. If missing, or set to zero,
the MAC will not apply any delay.

Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 drivers/net/ethernet/microchip/sparx5/Makefile     |   3 +-
 .../ethernet/microchip/sparx5/lan969x/lan969x.c    |   1 +
 .../ethernet/microchip/sparx5/lan969x/lan969x.h    |   5 +
 .../microchip/sparx5/lan969x/lan969x_rgmii.c       | 224 +++++++++++++++++++++
 .../net/ethernet/microchip/sparx5/sparx5_main.h    |   2 +
 .../net/ethernet/microchip/sparx5/sparx5_port.c    |   6 +
 6 files changed, 240 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/microchip/sparx5/Makefile b/drivers/net/ethernet/microchip/sparx5/Makefile
index 4bf2a885a9da..3f34e83246a0 100644
--- a/drivers/net/ethernet/microchip/sparx5/Makefile
+++ b/drivers/net/ethernet/microchip/sparx5/Makefile
@@ -20,7 +20,8 @@ sparx5-switch-$(CONFIG_LAN969X_SWITCH) += lan969x/lan969x_regs.o \
 					  lan969x/lan969x.o \
 					  lan969x/lan969x_calendar.o \
 					  lan969x/lan969x_vcap_ag_api.o \
-					  lan969x/lan969x_vcap_impl.o
+					  lan969x/lan969x_vcap_impl.o \
+					  lan969x/lan969x_rgmii.o
 
 # Provide include files
 ccflags-y += -I$(srctree)/drivers/net/ethernet/microchip/vcap
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
index be49a99556fe..396f76b6eea5 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.c
@@ -340,6 +340,7 @@ static const struct sparx5_ops lan969x_ops = {
 	.set_port_mux            = &lan969x_port_mux_set,
 	.ptp_irq_handler         = &lan969x_ptp_irq_handler,
 	.dsm_calendar_calc       = &lan969x_dsm_calendar_calc,
+	.port_config_rgmii       = &lan969x_port_config_rgmii,
 };
 
 const struct sparx5_match_data lan969x_desc = {
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
index 4b91c47d6d21..9a7ddebecf1e 100644
--- a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x.h
@@ -67,4 +67,9 @@ static inline bool lan969x_port_is_rgmii(int portno)
 /* lan969x_calendar.c */
 int lan969x_dsm_calendar_calc(struct sparx5 *sparx5, u32 taxi,
 			      struct sparx5_calendar_data *data);
+
+/* lan969x_rgmii.c */
+int lan969x_port_config_rgmii(struct sparx5_port *port,
+			      struct sparx5_port_config *conf);
+
 #endif
diff --git a/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c
new file mode 100644
index 000000000000..4e422ca50828
--- /dev/null
+++ b/drivers/net/ethernet/microchip/sparx5/lan969x/lan969x_rgmii.c
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0+
+/* Microchip lan969x Switch driver
+ *
+ * Copyright (c) 2024 Microchip Technology Inc. and its subsidiaries.
+ */
+
+#include "lan969x.h"
+
+/* Tx clock selectors */
+#define LAN969X_RGMII_TX_CLK_SEL_125MHZ 1  /* 1000Mbps */
+#define LAN969X_RGMII_TX_CLK_SEL_25MHZ  2  /* 100Mbps */
+#define LAN969X_RGMII_TX_CLK_SEL_2M5MHZ 3  /* 10Mbps */
+
+/* Port speed selectors */
+#define LAN969X_RGMII_SPEED_SEL_10 0   /* Select 10Mbps speed */
+#define LAN969X_RGMII_SPEED_SEL_100 1  /* Select 100Mbps speed */
+#define LAN969X_RGMII_SPEED_SEL_1000 2 /* Select 1000Mbps speed */
+
+/* Clock delay selectors */
+#define LAN969X_RGMII_CLK_DELAY_SEL_1_0_NS 2  /* Phase shift 45deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_1_7_NS 3  /* Phase shift 77deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_2_0_NS 4  /* Phase shift 90deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS 5  /* Phase shift 112deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_3_0_NS 6  /* Phase shift 135deg */
+#define LAN969X_RGMII_CLK_DELAY_SEL_3_3_NS 7  /* Phase shift 147deg */
+
+#define LAN969X_RGMII_PORT_START_IDX 28 /* Index of the first RGMII port */
+#define LAN969X_RGMII_IFG_TX 4          /* TX Inter Frame Gap value */
+#define LAN969X_RGMII_IFG_RX1 5         /* RX1 Inter Frame Gap value */
+#define LAN969X_RGMII_IFG_RX2 1         /* RX2 Inter Frame Gap value */
+
+#define RGMII_PORT_IDX(port) ((port)->portno - LAN969X_RGMII_PORT_START_IDX)
+
+/* Get the tx clock selector based on the port speed. */
+static int lan969x_rgmii_get_clk_sel(int speed)
+{
+	return (speed == SPEED_10  ? LAN969X_RGMII_TX_CLK_SEL_2M5MHZ :
+		speed == SPEED_100 ? LAN969X_RGMII_TX_CLK_SEL_25MHZ :
+				     LAN969X_RGMII_TX_CLK_SEL_125MHZ);
+}
+
+/* Get the port speed selector based on the port speed. */
+static int lan969x_rgmii_get_speed_sel(int speed)
+{
+	return (speed == SPEED_10  ? LAN969X_RGMII_SPEED_SEL_10 :
+		speed == SPEED_100 ? LAN969X_RGMII_SPEED_SEL_100 :
+				     LAN969X_RGMII_SPEED_SEL_1000);
+}
+
+/* Get the clock delay selector based on the clock delay in picoseconds. */
+static int lan969x_rgmii_get_clk_delay_sel(struct sparx5_port *port,
+					   u32 delay_ps, u32 *clk_delay_sel)
+{
+	switch (delay_ps) {
+	case 0:
+		/* Hardware default selector. */
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS;
+		break;
+	case 1000:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_1_0_NS;
+		break;
+	case 1700:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_1_7_NS;
+		break;
+	case 2000:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_0_NS;
+		break;
+	case 2500:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_2_5_NS;
+		break;
+	case 3000:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_3_0_NS;
+		break;
+	case 3300:
+		*clk_delay_sel = LAN969X_RGMII_CLK_DELAY_SEL_3_3_NS;
+		break;
+	default:
+		dev_err(port->sparx5->dev, "Invalid RGMII delay: %u", delay_ps);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/* Configure the RGMII tx clock frequency. */
+static void lan969x_rgmii_tx_clk_config(struct sparx5_port *port,
+					struct sparx5_port_config *conf)
+{
+	u32 clk_sel = lan969x_rgmii_get_clk_sel(conf->speed);
+	u32 idx = RGMII_PORT_IDX(port);
+
+	/* Take the RGMII clock domain out of reset and set tx clock
+	 * frequency.
+	 */
+	spx5_rmw(HSIO_WRAP_RGMII_CFG_TX_CLK_CFG_SET(clk_sel) |
+		 HSIO_WRAP_RGMII_CFG_RGMII_TX_RST_SET(0) |
+		 HSIO_WRAP_RGMII_CFG_RGMII_RX_RST_SET(0),
+		 HSIO_WRAP_RGMII_CFG_TX_CLK_CFG |
+		 HSIO_WRAP_RGMII_CFG_RGMII_TX_RST |
+		 HSIO_WRAP_RGMII_CFG_RGMII_RX_RST,
+		 port->sparx5, HSIO_WRAP_RGMII_CFG(idx));
+}
+
+/* Configure the RGMII port device. */
+static void lan969x_rgmii_port_device_config(struct sparx5_port *port,
+					     struct sparx5_port_config *conf)
+{
+	u32 dtag, dotag, etype, speed_sel, idx = RGMII_PORT_IDX(port);
+
+	speed_sel = lan969x_rgmii_get_speed_sel(conf->speed);
+
+	etype = (port->vlan_type == SPX5_VLAN_PORT_TYPE_S_CUSTOM ?
+		 port->custom_etype :
+		 port->vlan_type == SPX5_VLAN_PORT_TYPE_C ?
+		 ETH_P_8021Q : ETH_P_8021AD);
+
+	dtag = port->max_vlan_tags == SPX5_PORT_MAX_TAGS_TWO;
+	dotag = port->max_vlan_tags != SPX5_PORT_MAX_TAGS_NONE;
+
+	/* Enable the MAC. */
+	spx5_wr(DEVRGMII_MAC_ENA_CFG_RX_ENA_SET(1) |
+		DEVRGMII_MAC_ENA_CFG_TX_ENA_SET(1),
+		port->sparx5, DEVRGMII_MAC_ENA_CFG(idx));
+
+	/* Configure the Inter Frame Gap. */
+	spx5_wr(DEVRGMII_MAC_IFG_CFG_TX_IFG_SET(LAN969X_RGMII_IFG_TX) |
+		DEVRGMII_MAC_IFG_CFG_RX_IFG1_SET(LAN969X_RGMII_IFG_RX1) |
+		DEVRGMII_MAC_IFG_CFG_RX_IFG2_SET(LAN969X_RGMII_IFG_RX2),
+		port->sparx5, DEVRGMII_MAC_IFG_CFG(idx));
+
+	/* Configure port data rate. */
+	spx5_wr(DEVRGMII_DEV_RST_CTRL_SPEED_SEL_SET(speed_sel),
+		port->sparx5, DEVRGMII_DEV_RST_CTRL(idx));
+
+	/* Configure VLAN awareness. */
+	spx5_wr(DEVRGMII_MAC_TAGS_CFG_TAG_ID_SET(etype) |
+		DEVRGMII_MAC_TAGS_CFG_PB_ENA_SET(dtag) |
+		DEVRGMII_MAC_TAGS_CFG_VLAN_AWR_ENA_SET(dotag) |
+		DEVRGMII_MAC_TAGS_CFG_VLAN_LEN_AWR_ENA_SET(dotag),
+		port->sparx5,
+		DEVRGMII_MAC_TAGS_CFG(idx));
+}
+
+/* Configure the RGMII delay lines in the MAC.
+ *
+ * We use the rx-internal-delay-ps" and "tx-internal-delay-ps" properties to
+ * configure the rx and tx delays for the MAC. If these properties are missing
+ * or set to zero, the MAC will not apply any delay.
+ *
+ * The PHY side delays are determined by the PHY mode
+ * (e.g. PHY_INTERFACE_MODE_RGMII_{ID, RXID, TXID}), and ignored by the MAC side
+ * entirely.
+ */
+static int lan969x_rgmii_delay_config(struct sparx5_port *port,
+				      struct sparx5_port_config *conf)
+{
+	u32 tx_clk_sel, rx_clk_sel, tx_delay_ps = 0, rx_delay_ps = 0;
+	u32 idx = RGMII_PORT_IDX(port);
+	int err;
+
+	of_property_read_u32(port->of_node, "rx-internal-delay-ps",
+			     &rx_delay_ps);
+
+	of_property_read_u32(port->of_node, "tx-internal-delay-ps",
+			     &tx_delay_ps);
+
+	err = lan969x_rgmii_get_clk_delay_sel(port, rx_delay_ps, &rx_clk_sel);
+	if (err)
+		return err;
+
+	err = lan969x_rgmii_get_clk_delay_sel(port, tx_delay_ps, &tx_clk_sel);
+	if (err)
+		return err;
+
+	/* Configure rx delay. */
+	spx5_rmw(HSIO_WRAP_DLL_CFG_DLL_RST_SET(0) |
+		 HSIO_WRAP_DLL_CFG_DLL_ENA_SET(1) |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_SET(!!rx_delay_ps) |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_SET(rx_clk_sel),
+		 HSIO_WRAP_DLL_CFG_DLL_RST |
+		 HSIO_WRAP_DLL_CFG_DLL_ENA |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_ENA |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_SEL,
+		 port->sparx5, HSIO_WRAP_DLL_CFG(idx, 0));
+
+	/* Configure tx delay. */
+	spx5_rmw(HSIO_WRAP_DLL_CFG_DLL_RST_SET(0) |
+		 HSIO_WRAP_DLL_CFG_DLL_ENA_SET(1) |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_ENA_SET(!!tx_delay_ps) |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_SEL_SET(tx_clk_sel),
+		 HSIO_WRAP_DLL_CFG_DLL_RST |
+		 HSIO_WRAP_DLL_CFG_DLL_ENA |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_ENA |
+		 HSIO_WRAP_DLL_CFG_DLL_CLK_SEL,
+		 port->sparx5, HSIO_WRAP_DLL_CFG(idx, 1));
+
+	return 0;
+}
+
+/* Configure GPIO's to be used as RGMII interface. */
+static void lan969x_rgmii_gpio_config(struct sparx5_port *port)
+{
+	u32 idx = RGMII_PORT_IDX(port);
+
+	/* Enable the RGMII on the GPIOs. */
+	spx5_wr(HSIO_WRAP_XMII_CFG_GPIO_XMII_CFG_SET(1), port->sparx5,
+		HSIO_WRAP_XMII_CFG(!idx));
+}
+
+int lan969x_port_config_rgmii(struct sparx5_port *port,
+			      struct sparx5_port_config *conf)
+{
+	int err;
+
+	err = lan969x_rgmii_delay_config(port, conf);
+	if (err)
+		return err;
+
+	lan969x_rgmii_tx_clk_config(port, conf);
+	lan969x_rgmii_gpio_config(port);
+	lan969x_rgmii_port_device_config(port, conf);
+
+	return 0;
+}
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
index c58d7841638e..3ae760da17e2 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_main.h
@@ -324,6 +324,8 @@ struct sparx5_ops {
 	irqreturn_t (*ptp_irq_handler)(int irq, void *args);
 	int (*dsm_calendar_calc)(struct sparx5 *sparx5, u32 taxi,
 				 struct sparx5_calendar_data *data);
+	int (*port_config_rgmii)(struct sparx5_port *port,
+				 struct sparx5_port_config *conf);
 };
 
 struct sparx5_main_io_resource {
diff --git a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
index 86d6c9e9ec7c..04bc8fffaf96 100644
--- a/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
+++ b/drivers/net/ethernet/microchip/sparx5/sparx5_port.c
@@ -1012,6 +1012,12 @@ int sparx5_port_config(struct sparx5 *sparx5,
 	if (err)
 		return err;
 
+	if (rgmii) {
+		err = ops->port_config_rgmii(port, conf);
+		if (err)
+			return err;
+	}
+
 	/* high speed device is already configured */
 	if (!rgmii && !high_speed_dev)
 		sparx5_port_config_low_set(sparx5, port, conf);

-- 
2.34.1

[PATCH net-next v4 9/9] dt-bindings: net: sparx5: document RGMII delays

[Daniel Machon]

The lan969x switch device supports two RGMII port interfaces that can be
configured for MAC level rx and tx delays. Document two new properties
{rx,tx}-internal-delay-ps in the bindings, used to select these delays.

Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
---
 .../bindings/net/microchip,sparx5-switch.yaml          | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
index dedfad526666..a73fc5036905 100644
--- a/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
+++ b/Documentation/devicetree/bindings/net/microchip,sparx5-switch.yaml
@@ -129,6 +129,24 @@ properties:
             minimum: 0
             maximum: 383
 
+          rx-internal-delay-ps:
+            description:
+              RGMII Receive Clock Delay defined in pico seconds, used to select
+              the DLL phase shift between 1000 ps (45 degree shift at 1Gbps) and
+              3300 ps (147 degree shift at 1Gbps). A value of 0 ps will disable
+              any delay. The Default is no delay.
+            enum: [0, 1000, 1700, 2000, 2500, 3000, 3300]
+            default: 0
+
+          tx-internal-delay-ps:
+            description:
+              RGMII Transmit Clock Delay defined in pico seconds, used to select
+              the DLL phase shift between 1000 ps (45 degree shift at 1Gbps) and
+              3300 ps (147 degree shift at 1Gbps). A value of 0 ps will disable
+              any delay. The Default is no delay.
+            enum: [0, 1000, 1700, 2000, 2500, 3000, 3300]
+            default: 0
+
         required:
           - reg
           - phys

-- 
2.34.1

Re: [PATCH net-next v4 5/9] net: sparx5: only return PCS for modes that require it

[Russell King (Oracle)]

On Fri, Dec 13, 2024 at 02:41:04PM +0100, Daniel Machon wrote:
> The RGMII ports have no PCS to configure. Make sure we only return the
> PCS for port modes that require it.
> 
> Signed-off-by: Daniel Machon <daniel.machon@microchip.com>

Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>

Thanks!

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH net-next v4 6/9] net: sparx5: verify RGMII speeds

[Russell King (Oracle)]

On Fri, Dec 13, 2024 at 02:41:05PM +0100, Daniel Machon wrote:
> When doing a port config, we verify the port speed against the PHY mode
> and supported speeds of that PHY mode. Add checks for the four RGMII phy
> modes: RGMII, RGMII_ID, RGMII_TXID and RGMII_RXID.
> 
> Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
> Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
> Signed-off-by: Daniel Machon <daniel.machon@microchip.com>

You do realise that phylink knows what speeds each interface supports
(see phylink_get_capabilities()) and restricts the media advertisement
to ensure that ethtool link modes that can't be supported by the MAC
capabilities and set of interfaces that would be used are not
advertised.

This should mean none of your verification ever triggers. If it does,
then I'd like to know about it.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

Re: [PATCH net-next v4 0/9] net: lan969x: add RGMII support

[Robert Marko]

On Fri, Dec 13, 2024 at 2:41 PM Daniel Machon
<daniel.machon@microchip.com> wrote:
>
> == Description:
>
> This series is the fourth of a multi-part series, that prepares and adds
> support for the new lan969x switch driver.
>
> The upstreaming efforts is split into multiple series (might change a
> bit as we go along):
>
>         1) Prepare the Sparx5 driver for lan969x (merged)
>
>         2) Add support for lan969x (same basic features as Sparx5
>            provides excl. FDMA and VCAP, merged).
>
>         3) Add lan969x VCAP functionality (merged).
>
>     --> 4) Add RGMII support.
>
>         5) Add FDMA support.
>
> == RGMII support:
>
> The lan969x switch device includes two RGMII port interfaces (port 28
> and 29) supporting data speeds of 1 Gbps, 100 Mbps and 10 Mbps.
>
> == Patch breakdown:
>
> Patch #1 does some preparation work.
>
> Patch #2 adds new function: is_port_rgmii() to the match data ops.
>
> Patch #3 uses the is_port_rgmii() in a number of places.
>
> Patch #4 makes sure that we do not configure an RGMII device as a
>          low-speed device, when doing a port config.
>
> Patch #5 makes sure we only return the PCS if the port mode requires
>          it.
>
> Patch #6 adds checks for RGMII PHY modes in sparx5_verify_speeds().
>
> Patch #7 adds registers required to configure RGMII.
>
> Patch #8 adds RGMII implementation.
>
> Patch #9 documents RGMII delays in the dt-bindings.
>
> Details are in the commit description of the individual patches
>
> To: UNGLinuxDriver@microchip.com
> To: Andrew Lunn <andrew+netdev@lunn.ch>
> To: David S. Miller <davem@davemloft.net>
> To: Eric Dumazet <edumazet@google.com>
> To: Jakub Kicinski <kuba@kernel.org>
> To: Paolo Abeni <pabeni@redhat.com>
> To: Lars Povlsen <lars.povlsen@microchip.com>
> To: Steen Hegelund <Steen.Hegelund@microchip.com>
> To: Horatiu Vultur <horatiu.vultur@microchip.com>
> To: Russell King <linux@armlinux.org.uk>
> To: jacob.e.keller@intel.com
> To: robh@kernel.org
> To: krzk+dt@kernel.org
> To: conor+dt@kernel.org
> Cc: devicetree@vger.kernel.org
> Cc: netdev@vger.kernel.org
> Cc: linux-kernel@vger.kernel.org
> Cc: linux-arm-kernel@lists.infradead.org
> Cc: robert.marko@sartura.hr
>
> Signed-off-by: Daniel Machon <daniel.machon@microchip.com>

Tested-by: Robert Marko <robert.marko@sartura.hr>

> ---
> Changes in v4:
>
> - Split patch #4 in v3 into two patches, where the new patch #5 handles
>   PCS selection, by returning the PCS only for ports that require it.
>
> - Got rid of the '|' symbol for {rx,tx}-internal-delay-ps property
>   description in the dt-bindings (patch #9).
>
> - Link to v3: https://lore.kernel.org/r/20241118-sparx5-lan969x-switch-driver-4-v3-0-3cefee5e7e3a@microchip.com
>
> Changes in v3:
>
> v2 was kindly tested by Robert Marko. Not carrying the tag to v3 since
> we have changes to the handling of the delays.
>
> - Modified lan969x_rgmii_delay_config() to not apply any MAC delay when
>   the {rx,tx}-internal-delay-ps properties are missing or set to 0
>   (patch #7).
>
> - Removed 'required' constraint from {rx-tx}-internal-delay-ps
>   properties. Also added description and default value (Patch #8).
>
> - Link to v2: https://lore.kernel.org/r/20241113-sparx5-lan969x-switch-driver-4-v2-0-0db98ac096d1@microchip.com
>
> Changes in v2:
>
>   Most changes are in patch #7. RGMII implementation has been moved to
>   it's own file lan969x_rgmii.c.
>
>   Details:
>
>     - Use ETH_P_8021Q and ETH_P_8021AD instead of the Sparx5 provided
>       equivalents (patch #7).
>     - Configure MAC delays through "{rx,tx}-internal-delay-ps"
>       properties (patch #7).
>     - Add selectors for all the phase shifts that the hardware supports
>       (instead of only 2.0 ns, patch #7).
>     - Add selectors for all the port speeds (instead of only 1000 mbps.)
>     - Document RGMII delays in dt-bindings.
>
>   - Link to v1: https://lore.kernel.org/r/20241106-sparx5-lan969x-switch-driver-4-v1-0-f7f7316436bd@microchip.com
>
> ---
> Daniel Machon (9):
>       net: sparx5: do some preparation work
>       net: sparx5: add function for RGMII port check
>       net: sparx5: use is_port_rgmii() throughout
>       net: sparx5: skip low-speed configuration when port is RGMII
>       net: sparx5: only return PCS for modes that require it
>       net: sparx5: verify RGMII speeds
>       net: lan969x: add RGMII registers
>       net: lan969x: add RGMII implementation
>       dt-bindings: net: sparx5: document RGMII delays
>
>  .../bindings/net/microchip,sparx5-switch.yaml      |  18 ++
>  drivers/net/ethernet/microchip/sparx5/Makefile     |   3 +-
>  .../ethernet/microchip/sparx5/lan969x/lan969x.c    |   5 +
>  .../ethernet/microchip/sparx5/lan969x/lan969x.h    |  10 +
>  .../microchip/sparx5/lan969x/lan969x_rgmii.c       | 224 +++++++++++++++++++++
>  .../net/ethernet/microchip/sparx5/sparx5_main.c    |  29 ++-
>  .../net/ethernet/microchip/sparx5/sparx5_main.h    |   3 +
>  .../ethernet/microchip/sparx5/sparx5_main_regs.h   | 145 +++++++++++++
>  .../net/ethernet/microchip/sparx5/sparx5_phylink.c |  14 +-
>  .../net/ethernet/microchip/sparx5/sparx5_port.c    |  57 ++++--
>  .../net/ethernet/microchip/sparx5/sparx5_port.h    |   5 +
>  11 files changed, 484 insertions(+), 29 deletions(-)
> ---
> base-commit: 2c27c7663390d28bc71e97500eb68e0ce2a7223f
> change-id: 20241104-sparx5-lan969x-switch-driver-4-d59b7820485a
>
> Best regards,
> --
> Daniel Machon <daniel.machon@microchip.com>
>


-- 
Robert Marko
Staff Embedded Linux Engineer
Sartura d.d.
Lendavska ulica 16a
10000 Zagreb, Croatia
Email: robert.marko@sartura.hr
Web: www.sartura.hr

Re: [PATCH net-next v4 6/9] net: sparx5: verify RGMII speeds

[Daniel Machon]

> On Fri, Dec 13, 2024 at 02:41:05PM +0100, Daniel Machon wrote:
> > When doing a port config, we verify the port speed against the PHY mode
> > and supported speeds of that PHY mode. Add checks for the four RGMII phy
> > modes: RGMII, RGMII_ID, RGMII_TXID and RGMII_RXID.
> >
> > Reviewed-by: Steen Hegelund <Steen.Hegelund@microchip.com>
> > Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
> > Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
> 
> You do realise that phylink knows what speeds each interface supports
> (see phylink_get_capabilities()) and restricts the media advertisement
> to ensure that ethtool link modes that can't be supported by the MAC
> capabilities and set of interfaces that would be used are not
> advertised.
> 
> This should mean none of your verification ever triggers. If it does,
> then I'd like to know about it.

Yes, I agree. Having an extra look at phylink, these checks should not trigger
at all.

As it is, the default switch case is to throw an error, so without this
addition, the sparx5_port_verify_speed() function will fail when the PHY mode
is any of RGMII{_ID,_TXID,_RXID}. This patch just follows the established
pattern of adding the new PHY mode and checking the speed. TBH, I think that
all the checks in this function can be removed entirely, but that is something
I would like to verify and follow up on in a separate series, if that is OK? 

Thanks.

/Daniel

Re: [PATCH net-next v4 9/9] dt-bindings: net: sparx5: document RGMII delays

[Rob Herring (Arm)]

On Fri, 13 Dec 2024 14:41:08 +0100, Daniel Machon wrote:
> The lan969x switch device supports two RGMII port interfaces that can be
> configured for MAC level rx and tx delays. Document two new properties
> {rx,tx}-internal-delay-ps in the bindings, used to select these delays.
> 
> Signed-off-by: Daniel Machon <daniel.machon@microchip.com>
> ---
>  .../bindings/net/microchip,sparx5-switch.yaml          | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 

Reviewed-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH net-next v4 0/9] net: lan969x: add RGMII support

[Daniel Machon]

I would like to defer the pontential removal of sparx5_port_verify_speed()
function to a separate series (see comments on patch 6/9).  Any chance for a
maintainer to give the OK for that? I would like to give this series another
spin before net-next closes. No changes in next version - except adding TB and
RB tags.

/Daniel 

Re: [PATCH net-next v4 0/9] net: lan969x: add RGMII support

[Russell King (Oracle)]

On Wed, Dec 18, 2024 at 02:33:54PM +0000, Daniel Machon wrote:
> I would like to defer the pontential removal of sparx5_port_verify_speed()
> function to a separate series (see comments on patch 6/9).  Any chance for a
> maintainer to give the OK for that? I would like to give this series another
> spin before net-next closes. No changes in next version - except adding TB and
> RB tags.

There's no need to respin just to pick up tags that have been given -
patchwork will pick those up automatically.

I'd rather not have the current patch 6 merged, because we've had cases
in the past where stuff has been merged with "we'll fix it later" but
later doesn't seem to happen. We especially take this approach with new
kernel internal API functions - we don't merge them without a user,
because we've had too many cases where the user never appears.

We're currently at -rc5, which means -rc6 this Sunday 5th, -rc7 likely
next Sunday 12th, and probably the merge window opening on the 19th.
I think there's enough time for sparx5_port_verify_speed() to be
dropped during that window.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!