Re: [PATCH v4 3/5] net: mdio: ipq4019: configure CMN PLL clock for ipq5332

[Bryan O'Donoghue <bryan.odonoghue@linaro.org>]

On 25/12/2023 08:44, Luo Jie wrote:
> The reference clock of CMN PLL block is selectable, the internal
> 48MHZ is used by default.
> 
> The output clock of CMN PLL block is for providing the clock
> source of ethernet device(such as qca8084), there are 1 * 25MHZ
> and 3 * 50MHZ output clocks available for the ethernet devices.
> 
> Signed-off-by: Luo Jie <quic_luoj@quicinc.com>
> ---
>   drivers/net/mdio/mdio-ipq4019.c | 129 +++++++++++++++++++++++++++++++-
>   1 file changed, 128 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/net/mdio/mdio-ipq4019.c b/drivers/net/mdio/mdio-ipq4019.c
> index e24b0e688b10..e4862ac02026 100644
> --- a/drivers/net/mdio/mdio-ipq4019.c
> +++ b/drivers/net/mdio/mdio-ipq4019.c
> @@ -44,6 +44,17 @@
>   /* Maximum SOC PCS(uniphy) number on IPQ platform */
>   #define ETH_LDO_RDY_CNT				3
>   
> +#define CMN_PLL_REFERENCE_SOURCE_SEL		0x28
> +#define CMN_PLL_REFCLK_SOURCE_DIV		GENMASK(9, 8)
> +
> +#define CMN_PLL_REFERENCE_CLOCK			0x784
> +#define CMN_PLL_REFCLK_EXTERNAL			BIT(9)
> +#define CMN_PLL_REFCLK_DIV			GENMASK(8, 4)
> +#define CMN_PLL_REFCLK_INDEX			GENMASK(3, 0)
> +
> +#define CMN_PLL_POWER_ON_AND_RESET		0x780
> +#define CMN_ANA_EN_SW_RSTN			BIT(6)
> +
>   enum mdio_clk_id {
>   	MDIO_CLK_MDIO_AHB,
>   	MDIO_CLK_UNIPHY0_AHB,
> @@ -55,6 +66,7 @@ enum mdio_clk_id {
>   
>   struct ipq4019_mdio_data {
>   	void __iomem *membase;
> +	void __iomem *cmn_membase;
>   	void __iomem *eth_ldo_rdy[ETH_LDO_RDY_CNT];
>   	struct clk *clk[MDIO_CLK_CNT];
>   };
> @@ -227,12 +239,116 @@ static int ipq4019_mdio_write_c22(struct mii_bus *bus, int mii_id, int regnum,
>   	return 0;
>   }
>   
> +/* For the CMN PLL block, the reference clock can be configured according to
> + * the device tree property "qcom,cmn-ref-clock-frequency", the internal 48MHZ
> + * is used by default.
> + *
> + * The output clock of CMN PLL block is provided to the ethernet devices,
> + * threre are 4 CMN PLL output clocks (1*25MHZ + 3*50MHZ) enabled by default.
> + *
> + * Such as the output 50M clock for the qca8084 ethernet PHY.
> + */
> +static int ipq_cmn_clock_config(struct mii_bus *bus)
> +{
> +	struct ipq4019_mdio_data *priv;
> +	u32 reg_val, src_sel, ref_clk;
> +	int ret;
> +
> +	priv = bus->priv;
> +	if (priv->cmn_membase) {

if (!priv->cnm_membase)
	return 0;

then move the indentation here one tab left.

---
bod