Re: [PATCH 2/3] clk: qcom: ipq6018: add USB GDSCs

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 11/13/23 13:50, Robert Marko wrote:
> On Mon, 13 Nov 2023 at 12:58, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>
>> On 11.11.2023 12:28, Robert Marko wrote:
>>> On Tue, 7 Nov 2023 at 22:51, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>>>
>>>>
>>>>
>>>> On 10/31/23 10:01, Robert Marko wrote:
>>>>> On Mon, 30 Oct 2023 at 22:12, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>>>>>
>>>>>> On 30.10.2023 21:37, Robert Marko wrote:
>>>>>>> On Mon, 30 Oct 2023 at 20:37, Konrad Dybcio <konrad.dybcio@linaro.org> wrote:
>>>>>>>>
>>>>>>>> On 29.10.2023 12:04, Robert Marko wrote:
>>>>>>>>> On Wed, 25 Oct 2023 at 12:45, Robert Marko <robimarko@gmail.com> wrote:
>>>>>>>>>>
>>>>>>>>>> IPQ6018 has GDSC-s for each of the USB ports, so lets define them as such
>>>>>>>>>> and drop the curent code that is de-asserting the USB GDSC-s as part of
>>>>>>>>>> the GCC probe.
>>>>>>>>>>
>>>>>>>>>> Signed-off-by: Robert Marko <robimarko@gmail.com>
>>>>>>>>>
>>>>>>>>> Unfortunately, after testing on multiple devices I hit the same GDSC
>>>>>>>>> issue I had a long time ago
>>>>>>>>> that was the reason I did not send this upstream.
>>>>>>>>> It seems that USB3 port GDSC (USB0 GDSC in code) works just fine,
>>>>>>>>> however the USB2 one
>>>>>>>>> (USB1 GDSC in code) it is stuck off and USB2 port will fail due to this:
>>>>>>>>>       1.607531] ------------[ cut here ]------------
>>>>>>>>> [    1.607559] usb1_gdsc status stuck at 'off'
>>>>>>>>> [    1.607592] WARNING: CPU: 0 PID: 35 at gdsc_toggle_logic+0x16c/0x174
>>>>>>>>> [    1.615120] Modules linked in:
>>>>>>>> Can you dump GDSCR (the entire 32-bit register) at boot and when toggling?
>>>>>>>
>>>>>>> Sure, here it is:
>>>>>>> [    0.023760] qcom,gcc-ipq6018 1800000.gcc: reg: 0x3e078 val: 0x8222004 init
>>>>>>> [    0.023782] qcom,gcc-ipq6018 1800000.gcc: reg: 0x3f078 val: 0x8222004 init
>>>>>>> [    0.988626] qcom,gcc-ipq6018 1800000.gcc: reg: 0x3f078 val:
>>>>>>> 0x8282000 before toggle
>>>>>>> [    1.202506] qcom,gcc-ipq6018 1800000.gcc: reg: 0x3f078 val:
>>>>>>> 0x8282000 after toggle
>>>>>>> [    1.207208] qcom,gcc-ipq6018 1800000.gcc: reg: 0x3e078 val:
>>>>>>> 0xa0282000 before toggle
>>>>>> Any chance
>>>>>>
>>>>>> .en_few_wait_val = 0x2
>>>>>>
>>>>>> (turning BIT(19) into BIT(17))
>>>>>>
>>>>>> will make a difference?
>>>>>
>>>>> Sadly, it makes no difference and GDSC status bit newer comes up which is
>>>>> rather weird as USB0 one seems to work just fine.
>>>> What if you add clk_ignore_unused?
>>>
>>> To the USB1 master clock or?
>> That's a command line parameter, effectively setting it on all clks.
> 
> Oh that, I understand now.
> 
>>
>>>
>>> There is definitively something broken regarding the GDSC as
>>> GDSC_STATE bits (30-27)
>>> change from 0 to something on the USB0 GDSC but on GDSC1 they are 0 even after
>>> SW_OVERRIDE BIT(2) is set to 1, and the POWER BIT(31) newer changes to 1.
>>>
>>> However, if you manually set BIT(2) to 1 then the USB1 master clock
>>> can come up so
>>> GDSC seems to work.
>>> USB1 (The USB2.0 HS) port is still broken after this if USB mass storage is used
>>> but that was present before the GDSC changes as well and I still need
>>> to figure out
>>> which quirk is missing for this.
>> Please try clk_ignore_unused and see if toggling the GDSC is still broken.
> 
> Sadly, passing clk_ignore_unused in the bootargs doesn't help, GDSC is
> still stuck off.
Hm, so it looks like there's no clock dependency for this GDSC..

Maybe some regulator needs to be turned on?

Can you try to add regulator-always-on to all vregs and retry?
(and keep clk_ignore_unused to be sure)

Konrad