devicetree.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Tobias Klauser <klto-xXYtEe5Xh1A@public.gmane.org>
To: nios2-dev-1eJk0qcHJCcaeqlQEoCUNoJY59XmG8rH@public.gmane.org
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org
Subject: Re: [Nios2-dev] [PATCHv2] Add devicetree support to altera_jtaguart
Date: Tue, 18 Jan 2011 17:35:57 +0100	[thread overview]
Message-ID: <20110118173557.48407296@fermion> (raw)
In-Reply-To: <4D2E52FF.5060102-CmkmPbn3yAE@public.gmane.org>

Hi Walter

A small comment on the patch is below, though I have not run it yet
(need some more time to get everything started with devicetree here).

On Thu, 13 Jan 2011 02:18:55 +0100 Walter Goossens <waltergoossens-CmkmPbn3yAE@public.gmane.org> wrote:
> This patch adds devicetree support to the altera_jtaguart driver.
> Tested on hardware on the nios2 architecture.
>
> diff --git a/drivers/serial/altera_jtaguart.c b/drivers/serial/altera_jtaguart.c
> index f9b49b5..238348e 100644
> --- a/drivers/serial/altera_jtaguart.c
> +++ b/drivers/serial/altera_jtaguart.c
> @@ -433,15 +433,33 @@ static int __devinit altera_jtaguart_probe(struct platform_device *pdev)
>  	struct uart_port *port;
>  	int i;
>  
> -	for (i = 0; i < ALTERA_JTAGUART_MAXPORTS && platp[i].mapbase; i++) {
> +	for (i = 0; i < ALTERA_JTAGUART_MAXPORTS; i++) {
>  		port = &altera_jtaguart_ports[i].port;
>  
> +		if(platp)
> +		{
> +			if(!platp[i].mapbase)
> +				break;
> +
> +			port->mapbase = platp[i].mapbase;
> +			port->irq = platp[i].irq;
> +		} else {
> +#ifdef CONFIG_OF
> +			struct resource *res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
> +			struct resource *res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +			if((!res_mem) || (!res_irq))
> +				break;

We should return -ENODEV here if we fail to get the resources. If we
break here, we would return 0, which means the probe function was
successful, but this isn't the case.

> +
> +			port->mapbase = res_mem->start;
> +			port->irq = res_irq->start;
> +#else
> +			break;
> +#endif
> +		}
>  		port->line = i;
>  		port->type = PORT_ALTERA_JTAGUART;
> -		port->mapbase = platp[i].mapbase;
>  		port->membase = ioremap(port->mapbase, ALTERA_JTAGUART_SIZE);
>  		port->iotype = SERIAL_IO_MEM;
> -		port->irq = platp[i].irq;
>  		port->ops = &altera_jtaguart_ops;
>  		port->flags = ASYNC_BOOT_AUTOCONF;
>  
> @@ -464,6 +482,15 @@ static int __devexit altera_jtaguart_remove(struct platform_device *pdev)
>  
>  	return 0;
>  }
> +#ifdef CONFIG_OF
> +static struct of_device_id altera_jtaguart_match[] = {
> +	{ 
> +		.compatible = "altera,altera_juart",
> +	},
> +	{},
> +}
> +MODULE_DEVICE_TABLE(of, altera_jtaguart_match);
> +#endif /* CONFIG_OF */
> 
>  static struct platform_driver altera_jtaguart_platform_driver = {
>  	.probe	= altera_jtaguart_probe,
> @@ -471,6 +498,9 @@ static struct platform_driver altera_jtaguart_platform_driver = {
>  	.driver	= {
>  		.name	= DRV_NAME,
>  		.owner	= THIS_MODULE,
> +#ifdef CONFIG_OF
> +		.of_match_table = altera_jtaguart_match,
> +#endif
>  	},
>  };

  parent reply	other threads:[~2011-01-18 16:35 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2011-01-12 22:17 [PATCH] Add devicetree support to altera_jtaguart Walter Goossens
     [not found] ` <4D2E287B.7000005-CmkmPbn3yAE@public.gmane.org>
2011-01-12 23:06   ` Grant Likely
     [not found]     ` <20110112230607.GA31712-MrY2KI0G/OVr83L8+7iqerDks+cytr/Z@public.gmane.org>
2011-01-13  1:18       ` [PATCHv2] " Walter Goossens
     [not found]         ` <4D2E52FF.5060102-CmkmPbn3yAE@public.gmane.org>
2011-01-18 16:35           ` Tobias Klauser [this message]
2011-01-23 13:17             ` [PATCH v3] " Walter Goossens
     [not found]               ` <4D3C2A67.6030408-CmkmPbn3yAE@public.gmane.org>
2011-01-24 12:28                 ` Tobias Klauser
2011-01-13  1:25       ` [PATCH] " Walter Goossens

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20110118173557.48407296@fermion \
    --to=klto-xxytee5xh1a@public.gmane.org \
    --cc=devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ@public.gmane.org \
    --cc=nios2-dev-1eJk0qcHJCcaeqlQEoCUNoJY59XmG8rH@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).