* [PATCH 2/2] powerpc/5200: dts: digsy_mtc.dts: update to add can, pci, serial and spi
[not found] ` <1305561764-5942-1-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
@ 2011-05-16 16:02 ` Anatolij Gustschin
2011-07-06 9:43 ` [PATCH 1/2] powerpc/5200: mpc5200b.dtsi: add spi node address- and size-cells properties Anatolij Gustschin
1 sibling, 0 replies; 4+ messages in thread
From: Anatolij Gustschin @ 2011-05-16 16:02 UTC (permalink / raw)
To: linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ, Heiko Schocher
Add new nodes to describe more hardware the board is
equipped with:
- two can nodes for SJA1000 on localbus
- pci node to support Coral-PA graphics controller
- serial node for SC28L92 DUART on localbus
- spi node for MSP430 device
Also correct i2c eeprom node name.
Signed-off-by: Heiko Schocher <hs-ynQEQJNshbs@public.gmane.org>
Signed-off-by: Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>
---
arch/powerpc/boot/dts/digsy_mtc.dts | 50 ++++++++++++++++++++++++++++++++--
1 files changed, 47 insertions(+), 3 deletions(-)
diff --git a/arch/powerpc/boot/dts/digsy_mtc.dts b/arch/powerpc/boot/dts/digsy_mtc.dts
index 27bd267..e205d17 100644
--- a/arch/powerpc/boot/dts/digsy_mtc.dts
+++ b/arch/powerpc/boot/dts/digsy_mtc.dts
@@ -38,6 +38,14 @@
status = "disabled";
};
+ spi@f00 {
+ msp430@0 {
+ compatible = "spidev";
+ spi-max-frequency = <32000>;
+ reg = <0>;
+ };
+ };
+
psc@2000 { // PSC1
status = "disabled";
};
@@ -73,11 +81,16 @@
};
i2c@3d00 {
- rtc@50 {
+ eeprom@50 {
compatible = "at,24c08";
reg = <0x50>;
};
+ rtc@56 {
+ compatible = "mc,rv3029c2";
+ reg = <0x56>;
+ };
+
rtc@68 {
compatible = "dallas,ds1339";
reg = <0x68>;
@@ -90,11 +103,22 @@
};
pci@f0000d00 {
- status = "disabled";
+ interrupt-map-mask = <0xf800 0 0 7>;
+ interrupt-map = <0xc000 0 0 1 &mpc5200_pic 0 0 3
+ 0xc000 0 0 2 &mpc5200_pic 0 0 3
+ 0xc000 0 0 3 &mpc5200_pic 0 0 3
+ 0xc000 0 0 4 &mpc5200_pic 0 0 3>;
+ clock-frequency = <0>; // From boot loader
+ interrupts = <2 8 0 2 9 0 2 10 0>;
+ bus-range = <0 0>;
+ ranges = <0x42000000 0 0x80000000 0x80000000 0 0x10000000
+ 0x02000000 0 0x90000000 0x90000000 0 0x10000000
+ 0x01000000 0 0x00000000 0xa0000000 0 0x01000000>;
};
localbus {
- ranges = <0 0 0xff000000 0x1000000>;
+ ranges = <0 0 0xff000000 0x1000000
+ 4 0 0x60000000 0x0001000>;
// 16-bit flash device at LocalPlus Bus CS0
flash@0,0 {
@@ -122,5 +146,25 @@
reg = <0x00f00000 0x100000>;
};
};
+
+ can@4,0 {
+ compatible = "nxp,sja1000";
+ reg = <4 0x000 0x80>;
+ nxp,external-clock-frequency = <24000000>;
+ interrupts = <1 2 3>; // Level-low
+ };
+
+ can@4,100 {
+ compatible = "nxp,sja1000";
+ reg = <4 0x100 0x80>;
+ nxp,external-clock-frequency = <24000000>;
+ interrupts = <1 2 3>; // Level-low
+ };
+
+ serial@4,200 {
+ compatible = "nxp,sc28l92";
+ reg = <4 0x200 0x10>;
+ interrupts = <1 3 3>;
+ };
};
};
--
1.7.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* Re: [PATCH 1/2] powerpc/5200: mpc5200b.dtsi: add spi node address- and size-cells properties
[not found] ` <1305561764-5942-1-git-send-email-agust-ynQEQJNshbs@public.gmane.org>
2011-05-16 16:02 ` [PATCH 2/2] powerpc/5200: dts: digsy_mtc.dts: update to add can, pci, serial and spi Anatolij Gustschin
@ 2011-07-06 9:43 ` Anatolij Gustschin
2011-07-06 17:27 ` Grant Likely
1 sibling, 1 reply; 4+ messages in thread
From: Anatolij Gustschin @ 2011-07-06 9:43 UTC (permalink / raw)
To: Grant Likely
Cc: devicetree-discuss-uLR06cmDAlY/bJ5BZ2RsiQ,
linuxppc-dev-uLR06cmDAlY/bJ5BZ2RsiQ
Hi Grant,
can you please pick these patches for 3.1 ?
On Mon, 16 May 2011 18:02:43 +0200
Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org> wrote:
> Both, #address-cells and #size-cells properties are required
> for spi bus node, so add them.
>
> Signed-off-by: Anatolij Gustschin <agust-ynQEQJNshbs@public.gmane.org>
> ---
> arch/powerpc/boot/dts/mpc5200b.dtsi | 2 ++
> 1 files changed, 2 insertions(+), 0 deletions(-)
>
> diff --git a/arch/powerpc/boot/dts/mpc5200b.dtsi b/arch/powerpc/boot/dts/mpc5200b.dtsi
> index bc27548..7ab286a 100644
> --- a/arch/powerpc/boot/dts/mpc5200b.dtsi
> +++ b/arch/powerpc/boot/dts/mpc5200b.dtsi
> @@ -147,6 +147,8 @@
> };
>
> spi@f00 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi";
> reg = <0xf00 0x20>;
> interrupts = <2 13 0 2 14 0>;
Thanks,
Anatolij
^ permalink raw reply [flat|nested] 4+ messages in thread