Re: [PATCH 3/4] Enable ecc-mode selection in the driver

[Andrew Lunn <andrew-g2DYL2Zd6BY@public.gmane.org>]

On Tue, Jan 15, 2013 at 01:13:12PM +0100, Stefan Peter wrote:
> In order to be able to use the ecc-mode, add the bch module to the default
> settings for the kirwood boards and enable the activation in orin-nand.c
> 
> Signed-off-by: Stefan Peter <s.peter-R0yVo0h44Ow@public.gmane.org>
> ---
> diff --git a/arch/arm/configs/kirkwood_defconfig b/arch/arm/configs/kirkwood_defconfig
> index 93f3794..4a9d3f7 100644
> --- a/arch/arm/configs/kirkwood_defconfig
> +++ b/arch/arm/configs/kirkwood_defconfig
> @@ -84,6 +84,7 @@ CONFIG_MTD_CFI_STAA=y
>  CONFIG_MTD_PHYSMAP=y
>  CONFIG_MTD_M25P80=y
>  CONFIG_MTD_NAND=y
> +CONFIG_MTD_NAND_ECC_BCH=y
>  CONFIG_MTD_NAND_ORION=y
>  CONFIG_BLK_DEV_LOOP=y
>  # CONFIG_SCSI_PROC_FS is not set
> diff --git a/drivers/mtd/nand/orion_nand.c b/drivers/mtd/nand/orion_nand.c
> index cd72b92..1a35257 100644
> --- a/drivers/mtd/nand/orion_nand.c
> +++ b/drivers/mtd/nand/orion_nand.c
> @@ -14,6 +14,7 @@
>  #include <linux/module.h>
>  #include <linux/platform_device.h>
>  #include <linux/of.h>
> +#include <linux/of_mtd.h>
>  #include <linux/mtd/mtd.h>
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
> @@ -130,6 +131,7 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  		if (!of_property_read_u32(pdev->dev.of_node,
>  						"chip-delay", &val))
>  			board->chip_delay = (u8)val;
> +		board->ecc_mode = of_get_nand_ecc_mode(pdev->dev.of_node);

>  	} else
>  		board = pdev->dev.platform_data;
>  
> @@ -140,7 +142,8 @@ static int __init orion_nand_probe(struct platform_device *pdev)
>  	nc->IO_ADDR_R = nc->IO_ADDR_W = io_base;
>  	nc->cmd_ctrl = orion_nand_cmd_ctrl;
>  	nc->read_buf = orion_nand_read_buf;
> -	nc->ecc.mode = NAND_ECC_SOFT;
> +	nc->ecc.mode = board->ecc_mode == NAND_ECC_SOFT_BCH ?
> +		NAND_ECC_SOFT_BCH : NAND_ECC_SOFT;

Hi Stefan

What about a user that wants one of the other valid values?
NAND_ECC_OOB_FIRST, NAND_ECC_HW_SYNDROME, etc.

Would:

	if (IS_ERR(board->ecc_mode)) {
		nc->ecc.mode = NAND_ECC_SOFT;
		dev_info(&pdev->dev, "Defaulting to NAND_ECC_SOFT");
	} else
		nc->ecc.mode = board->ecc_mode

be better?

   Andrew