Re: Query on pinctrl usage for DT nodes

[Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>]

* Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org> [130403 11:42]:
> * Stephen Warren <swarren-3lzwWm7+Weoh9ZMKESR00Q@public.gmane.org> [130403 09:49]:
> > On 04/03/2013 03:16 AM, Prabhakar Lad wrote:
> > > Hi Linus/Stephen,
> > > 
> > > I am working adding  DT nodes for DA850.
> > > 
> > > Following is the pin control snippet of da850.dtsi:-
> > > 
> > > 		pmx_core: pinmux@1c14120 {
> > ...
> > >                         i2c0_pins: pinmux_i2c0_pins {
> > >                                 pinctrl-single,bits = <
> > >                                         /* I2C0_SDA,I2C0_SCL */
> > >                                         0x10 0x00002200 0x0000ff00
> > >                                 >;
> > >                         };
> > >                         mdio_pins: pinmux_mdio_pins {
> > >                                 pinctrl-single,bits = <
> > >                                         /* MDIO_CLK, MDIO_D */
> > >                                         0x10 0x00000088 0x000000ff
> > >                                 >;
> > >                         };
> > >                 }
> > > 
> > > And following is the code snippet for dts:-
> > > 
> > > 		i2c0: i2c@1c22000 {
> > > 			status = "okay";
> > > 			clock-frequency = <100000>;
> > > 			pinctrl-names = "default";
> > > 			pinctrl-0 = <&i2c0_pins>;
> > > 		};
> > > 		mdio: mdio@1e24000 {
> > > 			status = "okay";
> > > 			bus_freq = <2200000>;
> > > 			pinctrl-names = "default";
> > 
> > I assume there's also the following there:
> > 
> > 			pinctrl-0 = <&mdio_pins>;
> > 
> > >               };
> > > 		
> > > But while booting I see the following boot log:-
> > > ...
> > > cpuidle: using governor menu
> > > TCP: cubic registered
> > > NET: Registered protocol family 17
> > > pinctrl-single 1c14120.pinmux: pin 1c14130 already requested by
> > > davinci_mdio.0; cannot claim for i2c_davinci.1
> > > pinctrl-single 1c14120.pinmux: pin-4 (i2c_davinci.1) status -22
> > > pinctrl-single 1c14120.pinmux: could not request pin 4 on device pinctrl-single
> > > console [netcon0] enabled
> > > ....
> > > 
> > > This is because the mdio and i2c are using same pin 0x10,
> > 
> > How can two devices use the same pin? I mean physically, in hardware?
> > 
> > Is this because pinctrl-single uses the register address as the pin
> > number, whereas you have registers which configure multiple pins at
> > once? If so, your hardware isn't something that can be represented by
> > pinctrl-single.
> > 
> > > Is there any
> > > alternative way to handle if the two node's are using same pins any
> > > pointers could be very much helpful ?
> 
> It could also that the mux register(s) follow the one-mux-per-bit
> mapping.
> 
> In that case pinctrl-single,bits option as documented in the
> Documentation/devicetree/bindings/pinctrl/pinctrl-single.txt.

Oh it's already using pinctrl-single,bits option. Maybe there's a
bug, adding Peter to cc.

Regards,

Tony