[PATCH v4 0/6] ARM: imx6q{dl}: add the WEIM driver

[PATCH v4 0/6] ARM: imx6q{dl}: add the WEIM driver

[Huang Shijie]

This patch set adds a new driver for WEIM in the imx6q{dl}-sabreauto boards.

The WEIM(Wireless External Interface Module) works like a bus.
You can attach many different devices on it, such as NOR, onenand.

In the case of i.MX6q-sabreauto, only the NOR is connected to WEIM.

v3 --> v4:
	[0] use a more proper pad value for the data pins.
	[1] remove the weim_remove() hook.
	[2] remove the blank line.
	[3] use the lower case for the hex value.
	[4] add returne value for weim_parse_dt().
	[5] rename the pinctrls.

v2 --> v3:
	[0] split the NOR pinctrl.
	[1] make the driver unloaded. change to bool type in Kconfig.
	[2] use the of_platform_populate().
	[3] remove the unused "interrupt" property from the Doc.
v1 --> v2:
	[0] remove used PADs.
	[1] fix the wrong pad values, (thanks Alison Chaiken)
	[2] remove the weim-cs-index.
	[3] add "fsl" for the weim-cs-timing.
	[4] remove the partitions info in the document.
	[5] rewrite the drivers(follow Sascha and Shawn's comments)


Huang Shijie (6):
  drivers: bus: add a new driver for WEIM
  ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM
  ARM: dts: imx6qdl: add more information for WEIM
  ARM: dts: imx6q: add pinctrls for WEIM NOR
  ARM: dts: imx6dl: add pinctrls for WEIM NOR
  ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR

 Documentation/devicetree/bindings/bus/imx-weim.txt |   49 +++++++
 arch/arm/boot/dts/imx6dl-sabreauto.dts             |    9 +-
 arch/arm/boot/dts/imx6dl.dtsi                      |   58 ++++++++
 arch/arm/boot/dts/imx6q-sabreauto.dts              |    9 +-
 arch/arm/boot/dts/imx6q.dtsi                       |   59 +++++++++
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi           |   21 +++-
 arch/arm/boot/dts/imx6qdl.dtsi                     |    4 +-
 drivers/bus/Kconfig                                |    9 ++
 drivers/bus/Makefile                               |    1 +
 drivers/bus/imx-weim.c                             |  138 ++++++++++++++++++++
 10 files changed, 353 insertions(+), 4 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
 create mode 100644 drivers/bus/imx-weim.c

[PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Huang Shijie]

The WEIM(Wireless External Interface Module) works like a bus.
You can attach many different devices on it, such as NOR, onenand.

In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.

This patch also adds the devicetree binding document.
The driver only works when the devicetree is enabled.

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 Documentation/devicetree/bindings/bus/imx-weim.txt |   49 +++++++
 drivers/bus/Kconfig                                |    9 ++
 drivers/bus/Makefile                               |    1 +
 drivers/bus/imx-weim.c                             |  138 ++++++++++++++++++++
 4 files changed, 197 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
 create mode 100644 drivers/bus/imx-weim.c

diff --git a/Documentation/devicetree/bindings/bus/imx-weim.txt b/Documentation/devicetree/bindings/bus/imx-weim.txt
new file mode 100644
index 0000000..cedc2a9
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/imx-weim.txt
@@ -0,0 +1,49 @@
+Device tree bindings for i.MX Wireless External Interface Module (WEIM)
+
+The term "wireless" does not imply that the WEIM is literally an interface
+without wires. It simply means that this module was originally designed for
+wireless and mobile applications that use low-power technology.
+
+The actual devices are instantiated from the child nodes of a WEIM node.
+
+Required properties:
+
+ - compatible:		Should be set to "fsl,imx6q-weim"
+ - reg:			A resource specifier for the register space
+			(see the example below)
+ - clocks:		the clock, see the example below.
+ - #address-cells:	Must be set to 2 to allow memory address translation
+ - #size-cells:		Must be set to 1 to allow CS address passing
+ - ranges:		Must be set up to reflect the memory layout with four
+			integer values for each chip-select line in use:
+
+			   <cs-number> 0 <physical address of mapping> <size>
+
+Timing property for child nodes. It is mandatory, not optional.
+
+ - fsl,weim-cs-timing:	The timing array, contains 6 timing values for the
+			child node. We can get the CS index from the child
+			node's "reg" property. This property contains the values
+			for the registers EIM_CSnGCR1, EIM_CSnGCR2, EIM_CSnRCR1,
+			EIM_CSnRCR2, EIM_CSnWCR1, EIM_CSnWCR2 in this order.
+
+Example for an imx6q-sabreauto board, the NOR flash connected to the WEIM:
+
+	weim: weim@021b8000 {
+		compatible = "fsl,imx6q-weim";
+		reg = <0x021b8000 0x4000>;
+		clocks = <&clks 196>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		ranges = <0 0 0x08000000 0x08000000>;
+
+		nor@0,0 {
+			compatible = "cfi-flash";
+			reg = <0 0 0x02000000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bank-width = <2>;
+			fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+					0x0000c000 0x1404a38e 0x00000000>;
+		};
+	};
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index b05ecab..46cd5bb 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -4,6 +4,15 @@
 
 menu "Bus devices"
 
+config IMX_WEIM
+	bool "Freescale EIM DRIVER"
+	depends on ARCH_MXC
+	help
+	  Driver for i.MX6 WEIM controller.
+	  The WEIM(Wireless External Interface Module) works like a bus.
+	  You can attach many different devices on it, such as NOR, onenand.
+	  But now, we only support the Parallel NOR.
+
 config MVEBU_MBUS
 	bool
 	depends on PLAT_ORION
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index 3c7b53c..436bbcc 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -2,6 +2,7 @@
 # Makefile for the bus drivers.
 #
 
+obj-$(CONFIG_IMX_WEIM)	+= imx-weim.o
 obj-$(CONFIG_MVEBU_MBUS) += mvebu-mbus.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 
diff --git a/drivers/bus/imx-weim.c b/drivers/bus/imx-weim.c
new file mode 100644
index 0000000..349f14e
--- /dev/null
+++ b/drivers/bus/imx-weim.c
@@ -0,0 +1,138 @@
+/*
+ * EIM driver for Freescale's i.MX chips
+ *
+ * Copyright (C) 2013 Freescale Semiconductor, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/module.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/of_device.h>
+
+struct imx_weim {
+	void __iomem *base;
+	struct clk *clk;
+};
+
+static const struct of_device_id weim_id_table[] = {
+	{ .compatible = "fsl,imx6q-weim", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, weim_id_table);
+
+#define CS_TIMING_LEN 6
+#define CS_REG_RANGE  0x18
+
+/* Parse and set the timing for this device. */
+static int
+weim_timing_setup(struct platform_device *pdev, struct device_node *np)
+{
+	struct imx_weim *weim = platform_get_drvdata(pdev);
+	u32 value[CS_TIMING_LEN];
+	u32 cs_idx;
+	int ret;
+	int i;
+
+	/* get the CS index from this child node's "reg" property. */
+	ret = of_property_read_u32(np, "reg", &cs_idx);
+	if (ret)
+		return ret;
+
+	/* The weim has four chip selects. */
+	if (cs_idx > 3)
+		return -EINVAL;
+
+	ret = of_property_read_u32_array(np, "fsl,weim-cs-timing",
+					value, CS_TIMING_LEN);
+	if (ret)
+		return ret;
+
+	/* set the timing for WEIM */
+	for (i = 0; i < CS_TIMING_LEN; i++)
+		writel(value[i], weim->base + cs_idx * CS_REG_RANGE + i * 4);
+	return 0;
+}
+
+static int weim_parse_dt(struct platform_device *pdev)
+{
+	struct device_node *child;
+	int ret;
+
+	for_each_child_of_node(pdev->dev.of_node, child) {
+		if (!child->name)
+			continue;
+
+		ret = weim_timing_setup(pdev, child);
+		if (ret) {
+			dev_err(&pdev->dev, "%s set timing failed.\n",
+				child->full_name);
+			return ret;
+		}
+	}
+
+	ret = of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+	if (ret)
+		dev_err(&pdev->dev, "%s fail to create devices.\n",
+			pdev->dev.of_node->full_name);
+	return ret;
+}
+
+static int weim_probe(struct platform_device *pdev)
+{
+	struct imx_weim *weim;
+	struct resource *res;
+	int ret = -EINVAL;
+
+	weim = devm_kzalloc(&pdev->dev, sizeof(*weim), GFP_KERNEL);
+	if (!weim) {
+		ret = -ENOMEM;
+		goto weim_err;
+	}
+	platform_set_drvdata(pdev, weim);
+
+	/* get the resource */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	weim->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(weim->base)) {
+		ret = PTR_ERR(weim->base);
+		goto weim_err;
+	}
+
+	/* get the clock */
+	weim->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(weim->clk))
+		goto weim_err;
+
+	ret = clk_prepare_enable(weim->clk);
+	if (ret)
+		goto weim_err;
+
+	/* parse the device node */
+	ret = weim_parse_dt(pdev);
+	if (ret) {
+		clk_disable_unprepare(weim->clk);
+		goto weim_err;
+	}
+
+	dev_info(&pdev->dev, "WEIM driver registered.\n");
+	return 0;
+
+weim_err:
+	return ret;
+}
+
+static struct platform_driver weim_driver = {
+	.driver = {
+		.name = "imx-weim",
+		.of_match_table = weim_id_table,
+	},
+	.probe   = weim_probe,
+};
+
+module_platform_driver(weim_driver);
+MODULE_AUTHOR("Freescale Semiconductor Inc.");
+MODULE_DESCRIPTION("i.MX EIM Controller Driver");
+MODULE_LICENSE("GPL");
-- 
1.7.1

Re: [PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Sascha Hauer]

On Tue, May 28, 2013 at 02:20:07PM +0800, Huang Shijie wrote:
> The WEIM(Wireless External Interface Module) works like a bus.
> You can attach many different devices on it, such as NOR, onenand.
> 
> In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.
> 
> This patch also adds the devicetree binding document.
> The driver only works when the devicetree is enabled.
> 
> Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>

Looks good to me now. Thanks for working on this.

Acked-by: Sascha Hauer <s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>

Sascha


-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

Re: [PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Shawn Guo]

Hi Arnd,

On Tue, May 28, 2013 at 02:20:07PM +0800, Huang Shijie wrote:
> The WEIM(Wireless External Interface Module) works like a bus.
> You can attach many different devices on it, such as NOR, onenand.
> 
> In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.
> 
> This patch also adds the devicetree binding document.
> The driver only works when the devicetree is enabled.
> 
> Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/bus/imx-weim.txt |   49 +++++++
>  drivers/bus/Kconfig                                |    9 ++
>  drivers/bus/Makefile                               |    1 +
>  drivers/bus/imx-weim.c                             |  138 ++++++++++++++++++++

What's the general merge path for drivers/bus/ ones?  It's not clear to
me who is collecting those drivers/bus/ patches.

Shawn

>  4 files changed, 197 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
>  create mode 100644 drivers/bus/imx-weim.c

Re: [PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Shawn Guo]

On Tue, May 28, 2013 at 02:20:07PM +0800, Huang Shijie wrote:
> The WEIM(Wireless External Interface Module) works like a bus.
> You can attach many different devices on it, such as NOR, onenand.
> 
> In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.
> 
> This patch also adds the devicetree binding document.
> The driver only works when the devicetree is enabled.
> 
> Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> ---
>  Documentation/devicetree/bindings/bus/imx-weim.txt |   49 +++++++
>  drivers/bus/Kconfig                                |    9 ++
>  drivers/bus/Makefile                               |    1 +
>  drivers/bus/imx-weim.c                             |  138 ++++++++++++++++++++
>  4 files changed, 197 insertions(+), 0 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
>  create mode 100644 drivers/bus/imx-weim.c

Since no one is collecting drivers/bus/ patches right now, I just
applied the whole series to have the patch go via imx -> arm-soc.
Please let me know if there is any problem.

Shawn

Re: [PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Arnd Bergmann]

On Thursday 06 June 2013, Shawn Guo wrote:
> Since no one is collecting drivers/bus/ patches right now, I just
> applied the whole series to have the patch go via imx -> arm-soc.
> Please let me know if there is any problem.

I think that's fine.

	Arnd

Re: [PATCH v4 1/6] drivers: bus: add a new driver for WEIM

[Arnd Bergmann]

On Thursday 06 June 2013 23:09:37 Shawn Guo wrote:
> 
> On Tue, May 28, 2013 at 02:20:07PM +0800, Huang Shijie wrote:
> > The WEIM(Wireless External Interface Module) works like a bus.
> > You can attach many different devices on it, such as NOR, onenand.
> > 
> > In the case of i.MX6q-sabreauto, the NOR is connected to WEIM.
> > 
> > This patch also adds the devicetree binding document.
> > The driver only works when the devicetree is enabled.
> > 
> > Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
> > ---
> >  Documentation/devicetree/bindings/bus/imx-weim.txt |   49 +++++++
> >  drivers/bus/Kconfig                                |    9 ++
> >  drivers/bus/Makefile                               |    1 +
> >  drivers/bus/imx-weim.c                             |  138 ++++++++++++++++++++
> >  4 files changed, 197 insertions(+), 0 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/bus/imx-weim.txt
> >  create mode 100644 drivers/bus/imx-weim.c
> 
> Since no one is collecting drivers/bus/ patches right now, I just
> applied the whole series to have the patch go via imx -> arm-soc.
> Please let me know if there is any problem.

Sounds ok to me. If we see a lot of these, we can try to find a
maintainer.

	Arnd

[PATCH v4 2/6] ARM: dts: imx6q{dl}: fix the pin conflict between SPI and WEIM

[Huang Shijie]

In the imx6q-sabreauto and imx6dl-sabreauto boards,
the pin MX6Q{DL}_PAD_EIM_D19 is used as a GPIO for SPI NOR, but
it is used as a data pin for the WEIM NOR.

In order to fix the conflict, this patch removes the pin from the hog,
and adds a new board-level pinctrl: pinctrl_ecspi1_sabreauto.

The SPI NOR selects this pinctrl_ecspi1_sabreauto when it is enabled.

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/imx6dl-sabreauto.dts   |    9 ++++++++-
 arch/arm/boot/dts/imx6q-sabreauto.dts    |    9 ++++++++-
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi |    2 +-
 3 files changed, 17 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl-sabreauto.dts b/arch/arm/boot/dts/imx6dl-sabreauto.dts
index 60f3038..95da711 100644
--- a/arch/arm/boot/dts/imx6dl-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6dl-sabreauto.dts
@@ -25,7 +25,14 @@
 			fsl,pins = <
 				MX6DL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000
 				MX6DL_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
-				MX6DL_PAD_EIM_D19__GPIO3_IO19 	0x80000000
+			>;
+		};
+	};
+
+	ecspi1 {
+		pinctrl_ecspi1_sabreauto: ecspi1-sabreauto {
+			fsl,pins = <
+				MX6DL_PAD_EIM_D19__GPIO3_IO19  0x80000000
 			>;
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6q-sabreauto.dts b/arch/arm/boot/dts/imx6q-sabreauto.dts
index 9fb3e99..09a7580 100644
--- a/arch/arm/boot/dts/imx6q-sabreauto.dts
+++ b/arch/arm/boot/dts/imx6q-sabreauto.dts
@@ -29,7 +29,14 @@
 			fsl,pins = <
 				MX6Q_PAD_NANDF_CS2__GPIO6_IO15 0x80000000
 				MX6Q_PAD_SD2_DAT2__GPIO1_IO13  0x80000000
-				MX6Q_PAD_EIM_D19__GPIO3_IO19   0x80000000
+			>;
+		};
+	};
+
+	ecspi1 {
+		pinctrl_ecspi1_sabreauto: ecspi1-sabreauto {
+			fsl,pins = <
+				MX6Q_PAD_EIM_D19__GPIO3_IO19  0x80000000
 			>;
 		};
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index d6baa51..a4466e6 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -20,7 +20,7 @@
 	fsl,spi-num-chipselects = <1>;
 	cs-gpios = <&gpio3 19 0>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1_1>;
+	pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_sabreauto>;
 	status = "disabled"; /* pin conflict with WEIM NOR */
 
 	flash: m25p80@0 {
-- 
1.7.1

[PATCH v4 3/6] ARM: dts: imx6qdl: add more information for WEIM

[Huang Shijie]

Add the clock and compatible information for the weim.
Also adds the weim label.

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/imx6qdl.dtsi |    4 +++-
 1 files changed, 3 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index 42e461c..f21d259 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -744,9 +744,11 @@
 				reg = <0x021b4000 0x4000>;
 			};
 
-			weim@021b8000 {
+			weim: weim@021b8000 {
+				compatible = "fsl,imx6q-weim";
 				reg = <0x021b8000 0x4000>;
 				interrupts = <0 14 0x04>;
+				clocks = <&clks 196>;
 			};
 
 			ocotp@021bc000 {
-- 
1.7.1

[PATCH v4 4/6] ARM: dts: imx6q: add pinctrls for WEIM NOR

[Huang Shijie]

Add two pinctrls for WEIM:
   one for the weim nor, another for the chipselect.

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/imx6q.dtsi |   59 ++++++++++++++++++++++++++++++++++++++++++
 1 files changed, 59 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index ed11bcf..d79455d 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -323,6 +323,65 @@
 						>;
 					};
 				};
+
+				weim {
+					pinctrl_weim_cs0_1: weim_cs0grp-1 {
+						fsl,pins = <
+							MX6Q_PAD_EIM_CS0__EIM_CS0_B   0xb0b1
+						>;
+					};
+
+					pinctrl_weim_nor_1: weimnorgrp-1 {
+						fsl,pins = <
+							MX6Q_PAD_EIM_OE__EIM_OE_B     0xb0b1
+							MX6Q_PAD_EIM_RW__EIM_RW       0xb0b1
+							MX6Q_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+							/* data */
+							MX6Q_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+							MX6Q_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+							MX6Q_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+							MX6Q_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+							MX6Q_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+							MX6Q_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+							MX6Q_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+							MX6Q_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+							MX6Q_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+							MX6Q_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+							MX6Q_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+							MX6Q_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+							MX6Q_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+							MX6Q_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+							MX6Q_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+							MX6Q_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+							/* address */
+							MX6Q_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+							MX6Q_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+							MX6Q_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+							MX6Q_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+							MX6Q_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+							MX6Q_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+							MX6Q_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+							MX6Q_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+							MX6Q_PAD_EIM_DA15__EIM_AD15  0xb0b1
+							MX6Q_PAD_EIM_DA14__EIM_AD14  0xb0b1
+							MX6Q_PAD_EIM_DA13__EIM_AD13  0xb0b1
+							MX6Q_PAD_EIM_DA12__EIM_AD12  0xb0b1
+							MX6Q_PAD_EIM_DA11__EIM_AD11  0xb0b1
+							MX6Q_PAD_EIM_DA10__EIM_AD10  0xb0b1
+							MX6Q_PAD_EIM_DA9__EIM_AD09   0xb0b1
+							MX6Q_PAD_EIM_DA8__EIM_AD08   0xb0b1
+							MX6Q_PAD_EIM_DA7__EIM_AD07   0xb0b1
+							MX6Q_PAD_EIM_DA6__EIM_AD06   0xb0b1
+							MX6Q_PAD_EIM_DA5__EIM_AD05   0xb0b1
+							MX6Q_PAD_EIM_DA4__EIM_AD04   0xb0b1
+							MX6Q_PAD_EIM_DA3__EIM_AD03   0xb0b1
+							MX6Q_PAD_EIM_DA2__EIM_AD02   0xb0b1
+							MX6Q_PAD_EIM_DA1__EIM_AD01   0xb0b1
+							MX6Q_PAD_EIM_DA0__EIM_AD00   0xb0b1
+						>;
+					};
+
+				};
 			};
 		};
 
-- 
1.7.1

[PATCH v4 5/6] ARM: dts: imx6dl: add pinctrls for WEIM NOR

[Huang Shijie]

Add two pinctrls for WEIM:
   one for the weim nor, another for the chipselect.

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/imx6dl.dtsi |   58 +++++++++++++++++++++++++++++++++++++++++
 1 files changed, 58 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index 4b13454..2ecbcbc 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -183,6 +183,64 @@
 					};
 				};
 
+				weim {
+					pinctrl_weim_cs0_1: weim_cs0grp-1 {
+						fsl,pins = <
+							MX6DL_PAD_EIM_CS0__EIM_CS0_B   0xb0b1
+						>;
+					};
+
+					pinctrl_weim_nor_1: weim_norgrp-1 {
+						fsl,pins = <
+							MX6DL_PAD_EIM_OE__EIM_OE_B     0xb0b1
+							MX6DL_PAD_EIM_RW__EIM_RW       0xb0b1
+							MX6DL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060
+							/* data */
+							MX6DL_PAD_EIM_D16__EIM_DATA16 0x1b0b0
+							MX6DL_PAD_EIM_D17__EIM_DATA17 0x1b0b0
+							MX6DL_PAD_EIM_D18__EIM_DATA18 0x1b0b0
+							MX6DL_PAD_EIM_D19__EIM_DATA19 0x1b0b0
+							MX6DL_PAD_EIM_D20__EIM_DATA20 0x1b0b0
+							MX6DL_PAD_EIM_D21__EIM_DATA21 0x1b0b0
+							MX6DL_PAD_EIM_D22__EIM_DATA22 0x1b0b0
+							MX6DL_PAD_EIM_D23__EIM_DATA23 0x1b0b0
+							MX6DL_PAD_EIM_D24__EIM_DATA24 0x1b0b0
+							MX6DL_PAD_EIM_D25__EIM_DATA25 0x1b0b0
+							MX6DL_PAD_EIM_D26__EIM_DATA26 0x1b0b0
+							MX6DL_PAD_EIM_D27__EIM_DATA27 0x1b0b0
+							MX6DL_PAD_EIM_D28__EIM_DATA28 0x1b0b0
+							MX6DL_PAD_EIM_D29__EIM_DATA29 0x1b0b0
+							MX6DL_PAD_EIM_D30__EIM_DATA30 0x1b0b0
+							MX6DL_PAD_EIM_D31__EIM_DATA31 0x1b0b0
+							/* address */
+							MX6DL_PAD_EIM_A23__EIM_ADDR23 0xb0b1
+							MX6DL_PAD_EIM_A22__EIM_ADDR22 0xb0b1
+							MX6DL_PAD_EIM_A21__EIM_ADDR21 0xb0b1
+							MX6DL_PAD_EIM_A20__EIM_ADDR20 0xb0b1
+							MX6DL_PAD_EIM_A19__EIM_ADDR19 0xb0b1
+							MX6DL_PAD_EIM_A18__EIM_ADDR18 0xb0b1
+							MX6DL_PAD_EIM_A17__EIM_ADDR17 0xb0b1
+							MX6DL_PAD_EIM_A16__EIM_ADDR16 0xb0b1
+							MX6DL_PAD_EIM_DA15__EIM_AD15  0xb0b1
+							MX6DL_PAD_EIM_DA14__EIM_AD14  0xb0b1
+							MX6DL_PAD_EIM_DA13__EIM_AD13  0xb0b1
+							MX6DL_PAD_EIM_DA12__EIM_AD12  0xb0b1
+							MX6DL_PAD_EIM_DA11__EIM_AD11  0xb0b1
+							MX6DL_PAD_EIM_DA10__EIM_AD10  0xb0b1
+							MX6DL_PAD_EIM_DA9__EIM_AD09   0xb0b1
+							MX6DL_PAD_EIM_DA8__EIM_AD08   0xb0b1
+							MX6DL_PAD_EIM_DA7__EIM_AD07   0xb0b1
+							MX6DL_PAD_EIM_DA6__EIM_AD06   0xb0b1
+							MX6DL_PAD_EIM_DA5__EIM_AD05   0xb0b1
+							MX6DL_PAD_EIM_DA4__EIM_AD04   0xb0b1
+							MX6DL_PAD_EIM_DA3__EIM_AD03   0xb0b1
+							MX6DL_PAD_EIM_DA2__EIM_AD02   0xb0b1
+							MX6DL_PAD_EIM_DA1__EIM_AD01   0xb0b1
+							MX6DL_PAD_EIM_DA0__EIM_AD00   0xb0b1
+						>;
+					};
+
+				};
 
 			};
 
-- 
1.7.1

[PATCH v4 6/6] ARM: dts: imx6qdl-sabreauto: enable the WEIM NOR

[Huang Shijie]

Enable the WEIM NOR for imx6q{dl}-sabreauto boards.

For the pin conflict with SPI NOR, its status is set to "disabled".

Signed-off-by: Huang Shijie <b32955-KZfg59tc24xl57MIdRCFDg@public.gmane.org>
---
 arch/arm/boot/dts/imx6qdl-sabreauto.dtsi |   19 +++++++++++++++++++
 1 files changed, 19 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index a4466e6..e994011 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -58,3 +58,22 @@
 	wp-gpios = <&gpio1 13 0>;
 	status = "okay";
 };
+
+&weim {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_weim_nor_1 &pinctrl_weim_cs0_1>;
+	#address-cells = <2>;
+	#size-cells = <1>;
+	ranges = <0 0 0x08000000 0x08000000>;
+	status = "disabled"; /* pin conflict with SPI NOR */
+
+	nor@0,0 {
+		compatible = "cfi-flash";
+		reg = <0 0 0x02000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		bank-width = <2>;
+		fsl,weim-cs-timing = <0x00620081 0x00000001 0x1c022000
+				0x0000c000 0x1404a38e 0x00000000>;
+	};
+};
-- 
1.7.1