[PATCH 0/4] updates for tqma53.dtsi

[PATCH 0/4] updates for tqma53.dtsi

[Steffen Trumtrar]

Hi!

This series consists of misc updates for the tqma53.dtsi.
It is rebased to Shawns for-next branch.

Regards,
Steffen

Philipp Zabel (2):
  ARM i.MX53: tqma53: fix pinctrl settings
  ARM i.MX53: tqma53: rev 300 specific pin configuration

Sascha Hauer (1):
  ARM i.MX53: tqma53: Fix interrupt polarity for the mc34708

Steffen Trumtrar (1):
  ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2

 arch/arm/boot/dts/imx53-tqma53.dtsi | 45 +++++++++++++++++++++++--------------
 1 file changed, 28 insertions(+), 17 deletions(-)

-- 
1.8.2.rc2

[PATCH 1/4] ARM i.MX53: tqma53: Fix interrupt polarity for the mc34708

[Steffen Trumtrar]

From: Sascha Hauer <s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>

It's active high, not active low.

Signed-off-by: Sascha Hauer <s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 arch/arm/boot/dts/imx53-tqma53.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
index 38bed3e..3b2eb7d 100644
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
@@ -149,7 +149,7 @@
 		reg = <0x8>;
 		fsl,mc13xxx-uses-rtc;
 		interrupt-parent = <&gpio2>;
-		interrupts = <6 8>; /* PDATA_DATA6, low active */
+		interrupts = <6 4>; /* PATA_DATA6, active high */
 	};
 
 	sensor1: lm75@48 {
-- 
1.8.2.rc2

Re: [PATCH 1/4] ARM i.MX53: tqma53: Fix interrupt polarity for the mc34708

[Shawn Guo]

On Tue, Jun 04, 2013 at 11:12:27AM +0200, Steffen Trumtrar wrote:
> From: Sascha Hauer <s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> 
> It's active high, not active low.
> 
> Signed-off-by: Sascha Hauer <s.hauer-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>

Applied 1 ~ 3.

Shawn

[PATCH 2/4] ARM i.MX53: tqma53: fix pinctrl settings

[Steffen Trumtrar]

From: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>

BIT(31) is NO_PAD_CTL, not BIT(16)

Signed-off-by: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Signed-off-by: Steffen Trumtrar <s.trumtrar-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 arch/arm/boot/dts/imx53-tqma53.dtsi | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
index 3b2eb7d..45a273b 100644
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
@@ -72,11 +72,11 @@
 	i2s {
 		pinctrl_i2s_1: i2s-grp1 {
 			fsl,pins = <
-				 MX53_PAD_GPIO_19__GPIO4_5           0x10000 /* I2S_MCLK */
-				 MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC  0x10000 /* I2S_SCLK */
-				 MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD  0x10000 /* I2S_DOUT */
-				 MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x10000 /* I2S_LRCLK */
-				 MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD  0x10000 /* I2S_DIN */
+				 MX53_PAD_GPIO_19__GPIO4_5           0x80000000 /* I2S_MCLK */
+				 MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC  0x80000000 /* I2S_SCLK */
+				 MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD  0x80000000 /* I2S_DOUT */
+				 MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 /* I2S_LRCLK */
+				 MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD  0x80000000 /* I2S_DIN */
 			>;
 		};
 	};
@@ -84,16 +84,16 @@
 	hog {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				 MX53_PAD_EIM_CS1__IPU_DI1_PIN6  0x10000 /* VSYNC */
-				 MX53_PAD_EIM_DA15__IPU_DI1_PIN4 0x10000 /* HSYNC */
-				 MX53_PAD_PATA_DA_1__GPIO7_7     0x10000 /* LCD_BLT_EN */
-				 MX53_PAD_PATA_DA_2__GPIO7_8     0x10000 /* LCD_RESET */
-				 MX53_PAD_PATA_DATA5__GPIO2_5    0x10000 /* LCD_POWER */
-				 MX53_PAD_PATA_DATA6__GPIO2_6    0x10000 /* PMIC_INT */
-				 MX53_PAD_PATA_DATA14__GPIO2_14  0x10000 /* CSI_RST */
-				 MX53_PAD_PATA_DATA15__GPIO2_15  0x10000 /* CSI_PWDN */
-				 MX53_PAD_GPIO_0__GPIO1_0        0x10000 /* SYSTEM_DOWN */
-				 MX53_PAD_GPIO_3__GPIO1_3        0x10000
+				 MX53_PAD_EIM_CS1__IPU_DI1_PIN6  0x80000000 /* VSYNC */
+				 MX53_PAD_EIM_DA15__IPU_DI1_PIN4 0x80000000 /* HSYNC */
+				 MX53_PAD_PATA_DA_1__GPIO7_7     0x80000000 /* LCD_BLT_EN */
+				 MX53_PAD_PATA_DA_2__GPIO7_8     0x80000000 /* LCD_RESET */
+				 MX53_PAD_PATA_DATA5__GPIO2_5    0x80000000 /* LCD_POWER */
+				 MX53_PAD_PATA_DATA6__GPIO2_6    0x80000000 /* PMIC_INT */
+				 MX53_PAD_PATA_DATA14__GPIO2_14  0x80000000 /* CSI_RST */
+				 MX53_PAD_PATA_DATA15__GPIO2_15  0x80000000 /* CSI_PWDN */
+				 MX53_PAD_GPIO_0__GPIO1_0        0x80000000 /* SYSTEM_DOWN */
+				 MX53_PAD_GPIO_3__GPIO1_3        0x80000000
 			>;
 		};
 	};
-- 
1.8.2.rc2

[PATCH 3/4] ARM i.MX53: tqma53: rev 300 specific pin configuration

[Steffen Trumtrar]

From: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>

I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the
ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19.
Add #PHY_RESET and LCD_CONTRAST.

Signed-off-by: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
Signed-off-by: Steffen Trumtrar <s.trumtrar-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 arch/arm/boot/dts/imx53-tqma53.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
index 45a273b..450e4de 100644
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
@@ -72,7 +72,6 @@
 	i2s {
 		pinctrl_i2s_1: i2s-grp1 {
 			fsl,pins = <
-				 MX53_PAD_GPIO_19__GPIO4_5           0x80000000 /* I2S_MCLK */
 				 MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC  0x80000000 /* I2S_SCLK */
 				 MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD  0x80000000 /* I2S_DOUT */
 				 MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 /* I2S_LRCLK */
@@ -84,16 +83,17 @@
 	hog {
 		pinctrl_hog: hoggrp {
 			fsl,pins = <
-				 MX53_PAD_EIM_CS1__IPU_DI1_PIN6  0x80000000 /* VSYNC */
-				 MX53_PAD_EIM_DA15__IPU_DI1_PIN4 0x80000000 /* HSYNC */
+				 MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 /* SSI_MCLK */
 				 MX53_PAD_PATA_DA_1__GPIO7_7     0x80000000 /* LCD_BLT_EN */
 				 MX53_PAD_PATA_DA_2__GPIO7_8     0x80000000 /* LCD_RESET */
 				 MX53_PAD_PATA_DATA5__GPIO2_5    0x80000000 /* LCD_POWER */
 				 MX53_PAD_PATA_DATA6__GPIO2_6    0x80000000 /* PMIC_INT */
 				 MX53_PAD_PATA_DATA14__GPIO2_14  0x80000000 /* CSI_RST */
 				 MX53_PAD_PATA_DATA15__GPIO2_15  0x80000000 /* CSI_PWDN */
-				 MX53_PAD_GPIO_0__GPIO1_0        0x80000000 /* SYSTEM_DOWN */
+				 MX53_PAD_GPIO_19__GPIO4_5 	 0x80000000 /* #SYSTEM_DOWN */
 				 MX53_PAD_GPIO_3__GPIO1_3        0x80000000
+				 MX53_PAD_PATA_DA_0__GPIO7_6	 0x80000000 /* #PHY_RESET */
+				 MX53_PAD_GPIO_1__PWM2_PWMO	 0x80000000 /* LCD_CONTRAST */
 			>;
 		};
 	};
-- 
1.8.2.rc2

[PATCH 4/4] ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2

[Steffen Trumtrar]

Add WP/CD pinctrl for esdhc2.
Also, add vmmc-supply for esdhc2.

Signed-off-by: Steffen Trumtrar <s.trumtrar-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
---
 arch/arm/boot/dts/imx53-tqma53.dtsi | 13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
index 450e4de..9ecd198 100644
--- a/arch/arm/boot/dts/imx53-tqma53.dtsi
+++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
@@ -35,7 +35,9 @@
 
 &esdhc2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_esdhc2_1>;
+	pinctrl-0 = <&pinctrl_esdhc2_1>,
+		    <&pinctrl_esdhc2_2>;
+	vmmc-supply = <&reg_3p3v>;
 	wp-gpios = <&gpio1 2 0>;
 	cd-gpios = <&gpio1 4 0>;
 	status = "disabled";
@@ -69,6 +71,15 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hog>;
 
+	esdhc2_2 {
+		pinctrl_esdhc2_2: esdhc2-grp2 {
+			fsl,pins = <
+				MX53_PAD_GPIO_4__GPIO1_4	0x80000000 /* SD2_CD */
+				MX53_PAD_GPIO_2__GPIO1_2	0x80000000 /* SD2_WP */
+			>;
+		};
+	};
+
 	i2s {
 		pinctrl_i2s_1: i2s-grp1 {
 			fsl,pins = <
-- 
1.8.2.rc2

Re: [PATCH 4/4] ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2

[Shawn Guo]

On Tue, Jun 04, 2013 at 11:12:30AM +0200, Steffen Trumtrar wrote:
> Add WP/CD pinctrl for esdhc2.
> Also, add vmmc-supply for esdhc2.
> 
> Signed-off-by: Steffen Trumtrar <s.trumtrar-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> ---
>  arch/arm/boot/dts/imx53-tqma53.dtsi | 13 ++++++++++++-
>  1 file changed, 12 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
> index 450e4de..9ecd198 100644
> --- a/arch/arm/boot/dts/imx53-tqma53.dtsi
> +++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
> @@ -35,7 +35,9 @@
>  
>  &esdhc2 {
>  	pinctrl-names = "default";
> -	pinctrl-0 = <&pinctrl_esdhc2_1>;
> +	pinctrl-0 = <&pinctrl_esdhc2_1>,
> +		    <&pinctrl_esdhc2_2>;
> +	vmmc-supply = <&reg_3p3v>;
>  	wp-gpios = <&gpio1 2 0>;
>  	cd-gpios = <&gpio1 4 0>;
>  	status = "disabled";
> @@ -69,6 +71,15 @@
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_hog>;
>  
> +	esdhc2_2 {
> +		pinctrl_esdhc2_2: esdhc2-grp2 {

pinctrl_esdhc2_2 should be used by <soc>.dtsi to define the second pin
group for esdhc2 function, so please encode the board name in it to
avoid the name space conflict. 

Shawn

> +			fsl,pins = <
> +				MX53_PAD_GPIO_4__GPIO1_4	0x80000000 /* SD2_CD */
> +				MX53_PAD_GPIO_2__GPIO1_2	0x80000000 /* SD2_WP */
> +			>;
> +		};
> +	};
> +
>  	i2s {
>  		pinctrl_i2s_1: i2s-grp1 {
>  			fsl,pins = <
> -- 
> 1.8.2.rc2
> 

Re: [PATCH 4/4] ARM i.MX53: tqma53: add WP/CD pinctrl and vmmc to esdhc2

[Steffen Trumtrar]

On Thu, Jun 06, 2013 at 04:55:51PM +0800, Shawn Guo wrote:
> On Tue, Jun 04, 2013 at 11:12:30AM +0200, Steffen Trumtrar wrote:
> > Add WP/CD pinctrl for esdhc2.
> > Also, add vmmc-supply for esdhc2.
> > 
> > Signed-off-by: Steffen Trumtrar <s.trumtrar-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> > ---
> >  arch/arm/boot/dts/imx53-tqma53.dtsi | 13 ++++++++++++-
> >  1 file changed, 12 insertions(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi
> > index 450e4de..9ecd198 100644
> > --- a/arch/arm/boot/dts/imx53-tqma53.dtsi
> > +++ b/arch/arm/boot/dts/imx53-tqma53.dtsi
> > @@ -35,7 +35,9 @@
> >  
> >  &esdhc2 {
> >  	pinctrl-names = "default";
> > -	pinctrl-0 = <&pinctrl_esdhc2_1>;
> > +	pinctrl-0 = <&pinctrl_esdhc2_1>,
> > +		    <&pinctrl_esdhc2_2>;
> > +	vmmc-supply = <&reg_3p3v>;
> >  	wp-gpios = <&gpio1 2 0>;
> >  	cd-gpios = <&gpio1 4 0>;
> >  	status = "disabled";
> > @@ -69,6 +71,15 @@
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_hog>;
> >  
> > +	esdhc2_2 {
> > +		pinctrl_esdhc2_2: esdhc2-grp2 {
> 
> pinctrl_esdhc2_2 should be used by <soc>.dtsi to define the second pin
> group for esdhc2 function, so please encode the board name in it to
> avoid the name space conflict. 
> 

Hi!

Okay. I will fix that and resend.

Thanks,
Steffen

-- 
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |